Washer material and coating: which one belongs on this joint
Type decides what the washer has to do; material and coating decide whether it does that job under the bolt and survives the joint's environment. The rules below order the decision for plain, fender, spring lock, hardened, USS and SAE washers. Strength and hardness figures stay on the type comparison and on each type's own page.
The order of the decision
Start from the type, not from the material
A fender washer chosen for a coating is still a fender washer: it spans an oversized hole because of its outer diameter. Pick the type by the job — bearing area, locking friction, embedding under a high-class bolt — and the material second. Reversing the order leads to a well-protected washer that does the wrong job.
Match the hardness class to the bolt it seats
The bolt's property class and the washer's hardness have to agree. The 200 HV class pairs DIN 125 and DIN 9021 with assemblies up to property class 8.8; class 10.9 and 12.9 joints call for a hardened washer instead. Hardened F436 washers exist so the bolt stretches before the washer embeds — the principle is that the washer must be stronger than the bolt yield.
Finish the joint, then the coating
Coating follows the exposure the assembled joint sees, and it should be the same system the bolt carries — a hot-dip galvanized bolt with a bare zinc-plated washer leaves the washer as the weak point of the assembly.
Material and hardness
| Material and class | Where it belongs | What changes when you pick it |
|---|---|---|
| Low carbon / mild steel, 200 HV class | General bolted joints in steel, stainless and brass builds — the ordinary default for plain and fender washers. | Dimensioned for assemblies up to property class 8.8; needs a coating where moisture, salt or chemicals are present, zinc plating being the usual finish. |
| Hardened and tempered steel, ASTM F436 | Structural connections with F3125 A325/A490 bolts, and mandatory over slotted or oversized holes and under turn-of-nut tensioning. | Type 1 carbon steel, quenched and tempered, HRC 38–45 — a different scale and a different job from the 200 HV class, and the two are not converted. |
| Spring steel | Spring lock washers, whose function is friction. | No hardness class is tabulated for it on the collected pages; confirm it at RFQ. |
Stainless, brass and aluminium washers are outside this page's scope: the collected decision model above carries no stainless grade pairing, coating interaction or hardness class for them. Where one is required, state its grade and its pairing with the bolt on the RFQ rather than deriving them from this page.
Coatings
Zinc plating, hot-dip and the bearing face
Zinc plating is the ordinary finish for indoor and sheltered steel washers; hot-dip galvanizing is the outdoor and structural one. Both add thickness at the bearing face, so a coated washer's nominal thickness is not the bare steel thickness under it, and the joint's grip should be rechecked when the coating system changes.
Plating choice is not a hardness question
Hydrogen embrittlement is a property of the plating process, and hardened washers are where it matters. Specify the coating together with its post-plating treatment, and keep the washer's heat treatment and finish on the same purchase line so a supplier cannot split the two.
What to check on arrival
Documents follow the material claim
A material claim on the drawing is only as good as the document that carries it. Name the certificate type explicitly on the PO — an unnamed certificate requirement is typically satisfied by the cheapest document that fits the word. The guide Which EN 10204 certificate should your fastener PO name covers what each type proves and what it does not.
Hardness is a measurement, not a label
Where hardness decides the joint — a hardened washer under a high-class bolt, a spring lock washer in a vibration duty — the hardness band belongs on the certificate or on a separate inspection report, and an F436 washer is checked against the HRC 38–45 band, not a 200 HV figure.
Type and material together
The rule that matters most in practice sits where the two meet: a material change is not a type change. A hardened F436 washer in an unhardened position still does not stop the bolt from embedding into the part beneath it. Apply the material row above to the type the comparison already selected, and keep the washer's hardness class written on the drawing next to the bolt's class — the pair is what the joint is rated on.
Function, hardness class and example dimensions side by side: Washer types compared
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Washers inquiry
- ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
- ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
- ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
- ✓ Describe the bearing surface or locking function, quantity per size and destination.
- ✓ Factory-direct pricing for your Washers
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support