Bolt Head Markings: What the Lines, Numbers and Letters Claim — and How to Verify the Grade Before Accepting a Lot

Head markings identify the grade a bolt claims: SAE inch-series bolts use radial lines (three lines = Grade 5, six lines = Grade 8) 17, 10, metric bolts use a property class number such as 8.8 or 10.9 23, 27, and stainless bolts use an ISO 3506 letter-number code such as A2-70 or A4-80 15. The marking is a first-line identification aid, not proof of grade, so acceptance should rest on a mill test report with heat-number traceability and, for safety-critical joints, hardness or proof load testing 20, 23, 24. The sources do not reproduce the marking clauses of SAE J429, ISO 898-1, ASTM F3125 or ISO 3506, so the governing standard must be consulted directly for mandatory marking elements and per-grade property values.

Request a Quote

The head marking is a claim, not acceptance evidence

A stamped 10.9 or a set of six radial lines tells you what the bolt claims to be. It does not tell you what the bolt is. Head markings are only part of the identification process: a bolt can carry the correct strength marking and still be the wrong replacement if the thread, length, material, finish or geometry differ, and for engineered or safety-critical assemblies the equipment specification or drawing takes priority over a visual match 20. That is why the marking is best treated as the first rung of a verification ladder rather than the answer. The ladder runs from the visual head-marking check, to requesting the mill test report, to hardness testing, and to proof load testing where the application is safety-critical 23. For some grades the marking cannot carry the verification at all: where ductility is achieved through specific mechanical manipulation, visual inspection is impossible and the EN 10204 3.1 mill test certificate is the proof of metallurgical integrity 24. The sources do not establish that any specific marking is forged or misapplied in a given lot, or how often that occurs — so the practical stance is to verify, not to assume either way.

Read the marking system that matches the fastener family

Three marking systems cover most bolts a receiving inspector will see, and each encodes grade differently. SAE inch-series bolts carry radial lines on the head, and more lines means a stronger bolt: Grade 5 is marked with three radial lines and Grade 8 with six 17, 10. Metric bolts carry a numeric property class such as 8.8, 10.9 or 12.9, where the number before the decimal times 100 approximates minimum tensile strength in MPa and the number after the decimal times 10 approximates the yield-to-tensile percentage 23, 27. Stainless bolts use the ISO 3506 letter-number designation, where the letter identifies the steel group (A2 = 304, A4 = 316) and the number is one tenth of minimum tensile strength in MPa — so A4-80 is 316 stainless at roughly 800 MPa 15, 23. Absence of a marking is itself information: no marking typically means Grade 2 / Class 4.6 or lower 23. The first decision is therefore which system the part belongs to, because a line count and a decimal number are not interchangeable readings. If the head carries neither a recognisable line count nor a property class number, the marking does not claim a grade you can verify against, and the lot falls back to documentation and testing.

Documentation to demand with the lot

The marking cannot prove chemical composition or mechanical properties; the mill test report shows the actual composition and test results for the specific heat of steel the bolts came from 23. Across galvanizing, embrittlement-susceptible and structural applications, the documentation package consistently centres on material certification with heat-number traceability, process records and test results 5, 11, 25. Reject a lot whose paperwork does not carry that traceability.

  • Mill test report (MTR) showing chemical composition and mechanical test results for the specific heat of steel 23
  • Material certificate to EN 10204 Type 3.1 or 3.2, stating steel grade, heat number, chemical composition, mechanical properties and confirmation of compliance 11
  • Heat-number traceability linking the finished bolt back to the primary steel casting 24
  • Heat treatment record: austenitising temperature, quench medium, tempering temperature and time, furnace identification 11
  • Coating record and, where applicable, baking record with time commenced, furnace setpoint, part temperature verification and soak duration 11
  • Verification testing record: test method, number of specimens, test parameters, results and laboratory identification 11
  • For structural bolts, project-dependent additions: chemical composition reports, mechanical test results, dimensional and thread inspection, coating verification, lot traceability, marking verification and third-party inspection 25

Hardness screening and proof load: what each test proves

Hardness is a screening check, not a grade certificate. A portable Rockwell tester gives a fast read on whether the heat treatment matches the class the head claims, and values outside the class range indicate incorrect heat treatment or counterfeit product 23. Two sources give the same 39-44 HRC range for Class 12.9, which supports hardness testing as a screening check for that class 23, 14. Hardness testing alone does not prove tensile strength, proof load or material composition 23. Where the joint is safety-critical, the stronger check is a proof load test: sample bolts are subjected to the specified proof load per ISO 898-1 and checked for zero permanent elongation after the load is removed 23. The hardness ranges below are reported by a vendor-tier source and should be treated as screening bands to compare against, not as the standard's mandatory values.

Property classHardness range (HRC)What the buyer should do
Class 8.822-32 23Screen with portable Rockwell; outside range, hold the lot and request retest 23
Class 10.932-39 23Screen with portable Rockwell; outside range, hold the lot and request retest 23
Class 12.939-44 23, 14Screen with portable Rockwell; confirm against ISO 898-1 before release 23, 14

Check that the grade on the head is in scope of the standard being cited

A grade number on a head is only meaningful if the standard it belongs to actually covers that grade. Class 14.9 is not covered by ISO 898-1, whose scope extends only to Class 12.9 for standard commercial fasteners; ultra-high-strength grades are specified under aerospace standards such as the NAS, AN and MS series 9. A buyer who accepts a 14.9 marking as an ISO 898-1 grade is accepting a claim the standard does not make. The same scope problem appears across standard families. SAE J429 Grade 8 and ASTM A490 have similar strength levels but are made to different standards (SAE J429 vs ASTM F3125) and are generally not interchangeable in structural steel applications without engineering approval 10. So before treating a marking as a grade, confirm which standard family the part is being bought against, and whether that family covers the grade stamped on the head. If the drawing or equipment specification names a standard, that standard governs — not the number on the head 20.

Acceptance checks the marking cannot cover

The head marking does not carry dimensional or thread conformity, and no source in this set reproduces the marking-system clauses of SAE J429, ISO 898-1, ASTM F3125 or ISO 3506. Verify these against the governing standard rather than inferring them from the head.

  • Confirm the marking elements present (manufacturer identification, grade marking, source symbol, lot number) against the governing standard — the sources do not state which are mandatory, optional or prohibited 20, 25
  • Verify dimensional and thread conformity against the applicable standard; the head marking does not establish either 20, 25
  • Confirm the drawing or equipment specification takes priority over the visual match for safety-critical assemblies 20
  • For structural bolts, confirm marking verification and lot traceability are included in the inspection scope 25

Weighing the cost of the verification route

Verification costs money, and the sources give one concrete cost comparison for the documentation-heavy route. ASTM F2329 carries a 10-25% cost premium over ASTM A153 4. That premium is justified where the application is a critical structural connection, a high-strength fastener, or requires rigorous quality documentation 4. For general construction hardware in non-critical use, ASTM A153 provides adequate quality assurance with simplified procurement and lower cost 4. The same logic applies to the verification ladder: the marking check is free, the MTR is a paperwork request, and hardness or proof load testing adds lab time and cost. The sources do not give volume thresholds at which supplier-provided testing becomes cost-effective, nor lead-time implications of different verification approaches, so those trade-offs must be settled with the supplier rather than read off a table.

Two figures the sources dispute

Two numeric conflicts matter if you are about to quote a tensile strength or a grade equivalence in an acceptance decision. Neither source's table should be treated as the authoritative grade value; the governing standard must be consulted directly.

Disputed item with unitOne source reportsAnother reportsWhat the buyer should do
Tensile strength for metric Class 8.8 (MPa)400 MPa 16800 MPa 6Do not quote either; check ISO 898-1 directly 16, 6
SAE Grade 5 tensile strength (psi)120,000 psi minimum 1770 ksi 16Do not quote either; check SAE J429 directly 17, 16

Where markings collide, go missing, or stop being enough

The existing guide settles what a marking claims and why acceptance rests on documentation and testing. This section adds what buyers actually trip over at goods-in: marking systems that look alike across the inch/metric and SAE/ASTM boundaries, fasteners that are legally supplied unmarked, what a missing or suspicious marking does and does not let you conclude, and the pairing consequences that ride along with the grade the head claims.

The collision to train inspectors on is not within one system — it is across systems. Three radial lines mean SAE Grade 5 and six mean Grade 8 in the inch series, and a bare number like 8.8 or 10.9 identifies a metric property class (fastenereng.com); the two codes can be found in the same shipment when an importer mixes inventory. The line counts do not translate: metric class numbers encode tensile (8.8 ≈ 800 MPa, 10.9 ≈ 1000 MPa) rather than a grade ranking (chinastainless-steel.com). Structural heavy-hex bolts carry text, not lines — "A325" or "A490" plus the manufacturer's symbol (chinastainless-steel.com) — even though A325 and A490 are now technically covered under ASTM F3125 (blueribbonfastener.com). A second genuine collision: SAE Grade 8 also uses six radial markings (blueribbonfastener.com), so a Grade 8-marked hex bolt resembles a structural F3125 A325 Type 1 head in strength class but is manufactured to SAE J429 and is not interchangeable in structural steel applications without engineering approval (blueribbonfastener.com). The disambiguation rule is head style plus text: heavy hex head with letter text = structural series; standard hex with line count = SAE; bare decimal number = metric ISO 898-1.

Markings can be missing for legal, innocent reasons, which is why "unmarked = fake" is a wrong conclusion. ISO 898-1 requires marking only for property classes from 8.8 upward — low-strength 4.8 and 5.8 are normally supplied unmarked because they are general-purpose light-duty fasteners (chinastainless-steel.com). In the SAE system, Grade 2 commonly carries no radial grade lines at all (fastenereng.com). But the inverse inference also fails: the absence of radial lines should not be treated as universal proof that every unmarked bolt is Grade 2, because other standards use different marking systems and manufacturer symbols appear alongside grade markings (fastenereng.com). The defensible default is the conservative one the sources agree on: treat unmarked bolts as the low class they most likely are — class 4.8/5.8 unless certified otherwise (chinastainless-steel.com) — and never let an unmarked fastener into a structural or safety-critical joint that specified a marked grade. One genuine gap no corpus source closes: low-head, flange and small fastener geometries whose bearing surface physically cannot fit a standard marking are described nowhere in the collected sources, so this section cannot state which geometries are legally exempt — that stays unestablished.

A suspicious marking narrows suspicion; it does not convict. Markings enable traceability — the manufacturer's mark lets a lot be traced back to the mill certificate and heat number (chinastainless-steel.com) — so a marking that looks wrong (wrong font family for the claimed system, a heat number that will not cross-reference) shifts the verification from the head to the paper. The corpus documents the certificate-side risk directly: fake MTCs are a serious problem in the global steel supply chain, most common with materials sourced through intermediaries rather than directly from reputable mills (blog.projectmaterials.com). Detection moves off the bolt head entirely: contact the mill using independently sourced contact details, cross-reference heat/batch numbers on the MTC against physical product markings, and send random samples to an accredited lab for chemical and mechanical testing (blog.projectmaterials.com). None of the collected sources documents forged or misapplied head markings as a counterfeit method — the article's not_established list says so and this section does not paper over it: the documented counterfeit channel is the certificate, not the die.

The grade the head claims also constrains the nut, and the marking is where that pairing check starts. The structural case is codified: coating a structural nut requires overtapping, which reduces thread engagement and stripping strength, so only ASTM A563 Grades DH and DH3 and ASTM A194 Grade 2H nuts are suitable as overtapped coated nuts — proof load must exceed bolt tensile strength (RCSC 2025, commentary to 2.8.1). At goods-in the check is readable without a lab: a galvanized structural bolt claiming A325 paired with a plain A563-C nut is a marking-visible pairing failure, not a subtlety. The same reading discipline catches the metric version the sources flag: a class 10 nut on a class 8.8 bolt is wrong (chinastainless-steel.com). And when the claimed grade is A490, the coating line on the quote is itself checkable — applying zinc to A490 bolts by galvanizing, metallizing, or mechanical coating is not permitted (RCSC 2025, commentary to 2.8.1), so an "A490"-marked bolt that arrives hot-dip galvanized is self-refuting regardless of what the head says.

When markings stop being enough, the escalation is graded, not binary. First escalation is paper: request the mill certificate with heat number for project-critical lots and inspect markings at goods-in (chinastainless-steel.com), checking that the marking, the certificate heat number and the purchase order all agree. Second escalation is mechanical screening where the article's hardness-and-proof-load step applies — worth noting the corpus stakes the strength numbers behind it: Grade 5 at 120 ksi tensile / 92 ksi yield versus Grade 8 at 150 ksi / 130 ksi in the 1/4–1 in range (amesweb.info), with SAE Grade 8 offered at strength levels similar to A490 but under a different standard (blueribbonfastener.com). Third escalation, for intermediated supply where certificate fraud is realistic, is independent verification: third-party inspection to witness tests at the mill, PMI (XRF/OES) on arrival to verify alloy, or accredited-lab sample testing of chemical and mechanical properties (blog.projectmaterials.com). What markings can never do, under any escalation, is convert a claim into a property: a head mark asserts a grade; only the certificate chain and the test report demonstrate one.

Situation at goods-inWhat the marking lets you concludeWhat it does NOTEscalation
3 radial lines, standard hex headClaims SAE Grade 5 (fastenereng.com)Proof of the grade; acceptance still rests on docs/testsMatch cert heat number; hardness screen if the lot matters
Bare number 8.8 / 10.9Claims a metric property class (fastenereng.com)Nothing about SAE equivalence — the systems do not translate (chinastainless-steel.com)Pair-check the nut class; cert for project lots
"A325"/"A490" text, heavy hex headClaims the structural series under F3125 (chinastainless-steel.com; blueribbonfastener.com)That a Grade-8-marked SAE bolt is a substitute — it is not, without engineering approval (blueribbonfastener.com)Coating legality check; overtapped nut grade DH/DH3/2H (RCSC 2.8.1)
No marking at allLikely class 4.8/5.8 (ISO 898-1 marks only ≥8.8) or SAE Grade 2 (chinastainless-steel.com; fastenereng.com)NOT universal proof it is Grade 2; other standards mark differently (fastenereng.com)Treat as 4.8/5.8 unless certified otherwise; keep out of specified-grade joints
Marking looks wrong / intermediary supplyA reason to distrust the paper, not just the head (chinastainless-steel.com)Conviction — no source documents forged head markings; the documented fraud channel is the certificate (blog.projectmaterials.com)Verify MTC with the mill directly; heat-number cross-check; accredited-lab or PMI testing
"A490" bolt arrives galvanizedSelf-refuting — zinc coating on A490 by any galvanizing route is not permitted (RCSC 2025, 2.8.1)Nothing salvageable about the grade claimReject the lot; demand F2833 Gr1 / F1136 / zinc-flake alternative systems

No collected source states which low-head, flange or small-geometry fasteners are legally exempt from marking requirements under a specific standard; no source documents forged or misapplied head markings as a counterfeit method (the documented fraud channel is the certificate, not the die). Both gaps stay open rather than filled.

Sources for this section · 8
  1. 1 fastenereng.com Fastener Engineering
  2. 2 chinastainless-steel.com China Stainless Steel
  3. 3 blueribbonfastener.com Blue Ribbon Fastener
  4. 4 boltcouncil.org Research Council on Structural Connections (RCSC 2025)
  5. 5 amesweb.info AMESWeb
  6. 6 blog.projectmaterials.com Blog Projectmaterials
  7. 7 anabcofasteners.com Anabco Fasteners
  8. 8 californiafastener.com California Fastener

FAQ

What do bolt head markings (radial lines, numbers, letters) identify — and how can buyers verify fastener grade from the head marking alone?

Head markings identify the grade a bolt claims: SAE inch-series bolts use radial lines (three lines = Grade 5, six lines = Grade 8), metric bolts use a property class number such as 8.8 or 10.9, and stainless bolts use an ISO 3506 letter-number code such as A2-70 or A4-80. The marking is a first-line identification aid, not proof of grade, so acceptance should rest on a mill test report with heat-number traceability and, for safety-critical joints, hardness or proof load testing.

Do sources agree on Tensile strength value for metric property class 8.8?

The collected sources disagree: one reports "Class 8.8 tensile strength is 400 MPa (S16 table)" while another reports "8.8 grade steel tensile strength is 800 MPa (S6 preload example)". Treat the disagreement as a signal: verify the specific value for your size and speed with the supplier before ordering.

Do sources agree on Tensile strength values for SAE grades?

The collected sources disagree: one reports "SAE Grade 5 = 120,000 psi minimum, Grade 2 = 74,000 psi minimum (S17)" while another reports "SAE Grade 5 = 70 ksi, Grade 8 = 80 ksi (S16 table)". Treat the disagreement as a signal: verify the specific value for your size and speed with the supplier before ordering.

What is not established about Fastener Head Marking and Grade Identification: A Complete Guide?

No source reproduces the actual marking-system clauses of SAE J429, ISO 898-1, ASTM F3125 or ISO 3506. No source provides a complete marking-to-grade mapping table with tensile, yield and material for every grade. Where this matters to your order, ask the supplier for the specific test or datasheet value rather than accepting a general claim.

Related pages

Sources · 29
  1. 1 www.boltcouncil.org boltcouncil.org
  2. 2 www.hotdipgalvanizing.com hotdipgalvanizing.com
  3. 3 www.hotdipgalvanizing.com hotdipgalvanizing.com
  4. 4 www.hotdipgalvanizing.com hotdipgalvanizing.com
  5. 5 www.hotdipgalvanizing.com hotdipgalvanizing.com
  6. 6 www.kenenghardware.com kenenghardware.com
  7. 7 www.hotdipgalvanizing.com hotdipgalvanizing.com
  8. 8 www.hotdipgalvanizing.com hotdipgalvanizing.com
  9. 9 www.trojansf.co.uk trojansf.co.uk
  10. 10 www.blueribbonfastener.com blueribbonfastener.com
  11. 11 www.trojansf.co.uk trojansf.co.uk
  12. 12 www.trojansf.co.uk trojansf.co.uk
  13. 13 www.trojansf.co.uk trojansf.co.uk
  14. 14 www.trojansf.co.uk trojansf.co.uk
  15. 15 www.chinastainless-steel.com chinastainless-steel.com
  16. 16 www.kenenghardware.com kenenghardware.com
  17. 17 www.cyclonebolt.com cyclonebolt.com
  18. 18 www.trojansf.co.uk trojansf.co.uk
  19. 19 www.kenenghardware.com kenenghardware.com
  20. 20 www.fastenereng.com fastenereng.com
  21. 21 www.blueribbonfastener.com blueribbonfastener.com
  22. 22 www.kenenghardware.com kenenghardware.com
  23. 23 princefastener.com princefastener.com
  24. 24 anankafasteners.com anankafasteners.com
  25. 25 flybearindustrial.com flybearindustrial.com
  26. 26 nutsandbolts.com nutsandbolts.com
  27. 27 www.fastenersplus.com fastenersplus.com
  28. 28 kebafastenings.com kebafastenings.com
  29. 29 wilsongarner.com wilsongarner.com

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your inquiry

  • ✓ Standard and property class (e.g. DIN 912, ISO 4762, class 8.8) — or a drawing for custom parts.
  • ✓ Sizes, lengths and thread type (metric or inch).
  • ✓ Quantity per size and your target delivery date.
  • ✓ Destination country, plus any coating or finish requirement.
  • ✓ Any documents you need with the shipment (e.g. mill test certificate) so the quote includes them.
  • ✓ Your inquiry goes straight to the factory team by email and gets a reply within 24 hours.
  • ✓ Factory-direct pricing
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.