Spring-Wing Toggle Bolts
Spring-wing toggle bolts (butterfly anchors) in 1/8″–1/2″ sizes with matching machine-screw threads — 200–435 lb ultimate tension in 1/2″ wallboard and 310–2550 lb in hollow block, sized by the tabulated chart, head geometry and wing clearance included.
Last updated: 2026-11
Specifications
A spring-wing toggle bolt is a light-duty hollow-wall anchor in four parts: two matching steel wings bent at right angles, an internally threaded trunnion nut that pivots between them, a wire spring that holds the wings folded, and a machine screw. You drill the wallboard or hollow-block hole, compress the wings through it, and the spring snaps them open behind the wall so tightening the screw draws the folded wing set flat against the back face and clamps the fixture to the front. That spread over the back of a hollow wall is the whole point — load capacity comes from the wing bearing on the far face, not from the screw, which is why the chart’s holding values rise steeply with size in hollow block (310 lb at 1/8″ up to 2550 lb tension at 1/2″) and why embedment depth, not torque, is the size-dependent dimension to control. Toggle bolts are single-use: the wings cannot pass back through the hole once set, and repeated repositioning is not part of how they are assessed. They carry more temperature resistance than other hollow-wall anchors, which matters near lighting and heating fixtures.
| Type | Spring-wing toggle bolt (butterfly anchor) — wings + pivoting trunnion nut + spring + machine screw, single-use |
|---|---|
| Anchor sizes | 1/8″–1/2″ with matching machine-screw threads: 6-32, 10-24, 1/4-20, 5/16-18, 3/8-16, 1/2-13 |
| Drill bit per size | 3/8″ (1/8″) · 1/2″ (3/16″) · 5/8″ (1/4″) · 7/8″ (5/16″ and 3/8″) · 1-1/4″ (1/2″) — the bit, not the screw, sets the hole |
| Holding values (1/2″ wallboard) | Ultimate tension 200–435 lb and shear 205–470 lb by size; suggested safe working load = 1/4 of the tabulated values (source’s own rule) |
| Holding values (hollow block) | Ultimate tension 310–2550 lb and shear 270–3620 lb by size at the tabulated embedment depths (3/8″–1-1/4″) |
| Embedment depth | 3/8″ (1/8″) up to 1-1/4″ (1/2″) — minimum wall thickness behind which the wings must open |
| Head options | Mushroom head or round head; per-size head height/diameter and wing clearance tabulated (mushroom S max 0.321″–0.823″, round D max 0.260″–0.813″) |
| Materials | Wings: AISI 1008–1010 cold-rolled steel. Trunnion nut: AISI 1010 steel through 3/8″, Zamac alloy at 1/2″. Screw: carbon steel |
| Finish | Commonly supplied with a clear zinc finish |
| Applications | Hollow block and gypsum wallboard; single-use anchors; spread the load over a larger area and are more temperature resistant than other hollow-wall anchors |
| MOQ / lead time | 500–1,000 pieces; standard production 15–30 days |
| Anchor Size | Thread Size | Drill Bit Size | Mushroom Head Height (M) | Mushroom Head Diameter (S) | Round Head Height (R) | Round Head Diameter (D) | Wing Clearance (W) | Performance Information: In 1/2" Wallboard | In Hollow Block | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Max | Min | Max | Min | Max | Min | Max | Min | Tensile (lbs.) | Shear (lbs.) | Embedment Depth | Tensile (lbs.) | Shear (lbs.) | |||||
| 1/8 | 6-32 | 3/8 | .086 | .074 | .321 | .303 | .103 | .091 | .260 | .240 | 1-1/16 | 200 | 205 | 3/8 | 310 | 270 | |
| 3/16 | 10-24 | 1/2 | .128 | .113 | .448 | .425 | .137 | .123 | .359 | .334 | 1-3/8 | 245 | 280 | 1/2 | 430 | 700 | |
| 1/4 | 1/4-20 | 5/8 | .150 | .133 | .573 | .546 | .175 | .160 | .472 | .443 | 1-1/2 | 310 | 350 | 5/8 | 830 | 1390 | |
| 5/16 | 5/16-18 | 7/8 | .183 | .162 | .698 | .666 | .216 | .198 | .590 | .557 | 2-1/8 | 330 | 420 | 7/8 | 1070 | 2980 | |
| 3/8 | 3/8-16 | 7/8 | .215 | .191 | .823 | .787 | .256 | .237 | .708 | .670 | 2-1/8 | 340 | 440 | 7/8 | 1385 | 3120 | |
| 1/2 | 1/2-13 | 1-1/4 | .280 | .250 | 1.073 | 1.028 | .355 | .332 | .813 | .766 | 3 | 435 | 470 | 1-1/4 | 2550 | 3620 |
- Header row carried verbatim as a grid row (stacked "Max/Min" and load-group labels); the "Performance Information" super-group spans both the 1/2\" Wallboard (Tensile, Shear, Embedment Depth) and Hollow Block (Tensile, Shear) columns.
Materials
- Wing body: AISI 1008-1010 (or equivalent) cold-rolled steel
- Trunnion nut: AISI 1010 steel (1/4″–3/8″); Zamac alloy (1/2″)
- Machine screw: carbon steel
Ordering & documentation
Documents
Shipments of Spring-Wing Toggle Bolts are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Spring-Wing Toggle Bolts orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (Spring-Wing Toggle Bolts), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for spring-wing toggle bolts is 500–1,000 pieces (applies to the standard sizes and finishes for spring-wing toggle bolts; mixed, special or custom variants are quoted — final commercial terms per quotation) Standard production for spring-wing toggle bolts run 15–30 days. Quantities or variants of spring-wing toggle bolts outside the standard range are confirmed at quotation.
Storage & shipping
Spring-Wing Toggle Bolts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store spring-wing toggle bolts dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
How much weight can a toggle bolt hold?
The honest answer is per size and per base material, from the tabulated chart: in 1/2″ wallboard the ultimate tension runs 200 lb (1/8″) to 435 lb (1/2″), while in hollow block the same sizes span 310 lb to 2550 lb tension and up to 3620 lb shear. These are ultimate values — the manufacturer’s rule of thumb is to apply a safe working load of one quarter of them, so a 1/4″ toggle in wallboard works at roughly 78 lb. Do not read the hollow-block numbers onto plain drywall: the block values assume the embedment depth tabulated for each size and a back face the wings can bear on.
What drill bit does each toggle-bolt size need?
The bit, not the machine screw, sizes the hole: 3/8″ for the 1/8″ anchor, 1/2″ for 3/16″, 5/8″ for 1/4″, 7/8″ for both 5/16″ and 3/8″, and 1-1/4″ for 1/2″. The hole must be large enough for the folded wings to pass through but no larger than the chart’s wing clearance contemplates — an oversize hole lets the wing set rotate behind soft wallboard and drop the holding value below the tabulated figure.
Are toggle bolts reusable or repositionable?
No. They are single-use anchors: once the wings spring open behind the wall, they cannot pass back through the hole, and removing the screw releases the wing set into the cavity. Plan fixture locations before installation; for work that needs repositioning, use a hollow-wall anchor with a removable sleeve or a toggle designed for snap-off rails instead.
What should an RFQ for toggle bolts state?
State the anchor size and thread callout (for example 1/4-20), head style (mushroom or round), screw length for your wall thickness, finish (clear zinc or specified), and quantity per size — plus destination country and any required documents. If your fixture drawing calls out a specific brand of toggle, quote it; the size chart is common across suppliers but the screw length is not.
What is the MOQ and lead time for these anchors?
The minimum order quantity is 500–1,000 pieces. Standard production runs 15–30 days. Non-standard screw lengths or finishes are quoted against the specification.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Spring-Wing Toggle Bolts inquiry
- ✓ This listed family is cast-in foundation anchor rods, including L-shaped/bent rods; identify the ASTM F1554 grade or drawing.
- ✓ Give rod diameter/thread, overall length, hook length, projection and thread length as separate dimensions.
- ✓ Provide the supported base plate/structure details and the concrete design inputs, embedment, edge distance and spacing from the engineer’s design.
- ✓ State corrosion protection, quantity, destination and required material/lot certificates.
- ✓ Factory-direct pricing for your Spring-Wing Toggle Bolts
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support