Which washer belongs on which bolt: plain, lock and conical washers
A washer is chosen for one or more of three jobs — spread the bolt load over more material, keep the fastener from loosening, or separate the fastener from the contact surface — and each family of washers does one of those jobs better than the others. This hub sets out the families, the standards that define them (including the ones that are withdrawn but still sold under their old names), the decisions a buyer actually has to make, and what a washer certificate can and cannot prove.
01 · Overview
Four families cover the washers most bolted joints use. Plain washers — DIN 125 (ISO 7089), DIN 126 (ISO 7091), DIN 433, DIN 134, ASME B18.21.1 Type A and B, SAE and USS patterns — are flat rings that distribute bearing pressure and protect the contact face [R1, R2, R9, R11]. Spring lock washers — the split ring of DIN 127 and the two forms of DIN 128 — are shaped to hold a force against the joint after tightening [R3, R4]. Toothed and serrated lock washers carry teeth — DIN 6797 and DIN 6798 each run to an external form A, an internal form J and a third form V, and both standards state a minimum number of teeth per size [R5, R6, R21, R22, R23]. Conical spring washers — DIN 6796 — are described by their source as conical washers acting as heavy-duty spring discs loaded in the axial direction, and their dimension table carries a height range (max/min) for each size [R7]. A fifth family, the square taper washer of DIN 434, is shaped for a specific application rather than a general duty [R15]; it is included here because buyers meet it in the same washers section and frequently substitute it by size.
Scope note: hardened structural washers (ASTM F436), the HV chamfered washers of DIN 6916 / EN 14399-6 and HV washer sets belong to the structural-bolting cluster and are not covered here; link there for those. Sizes and per-standard dimension tables are not repeated on this page — they are on each specification page in §06.
02 · Specifications
What each family is defined by, compiled from the named sources. Ranges below describe the shape of each standard's series, not a stocked size list; per-size dimensions are on the specification pages. Where a property is not stated by the source for a family, the cell says so rather than borrowing a value from another family.
| Family | Standard | Defining geometry the source states | Hardness / material as stated by the source | Source |
|---|---|---|---|---|
| Plain washer | DIN 125 (DIN EN ISO 7089) | Flat ring; table M1.6–M160, columns nominal bore / max outside diameter / nominal thickness / mass. | Not stated by this source — set on the drawing / RFQ. | [R1, R10] |
| Plain washer, normal series | DIN 126 | Flat ring, normal series; table M5–M160 with nominal mass per 1000 pieces. | Not stated by this source. | [R2] |
| Plain washer | ISO 7089 / ISO 7090 | ISO 7089 is stated as the ISO equivalent of DIN 125 Type A and ISO 7090 of Type B (chamfered); shared M3–M72 series. | ISO flat-washer hardness classes 100 HV / 200 HV / 300 HV, selected by product grade and bolt property class. | [R9, R12] |
| Plain washer, large | DIN 134 | Larger outside diameter than the standard series; the collected grid covers nominal 3.2–21. | No materials or finishes printed on the source. | [R11] |
| Spring lock washer | DIN 127 A & B (withdrawn) | Open helical ring; separate minimum and maximum heights for type A and type B per size (M2 upward). | Sold in spring steel (distributor product record); standard states no hardness in the collected pages. | [R3, R13, R14, R19] |
| Curved spring lock washer | DIN 128 (withdrawn) | Spring ring in two forms (A and B); table with bore limits, outside diameter, section and height per size. | Not stated by this source. | [R4] |
| Toothed lock washer | DIN 6797 | Forms A / J / V; table with bore, OD, thickness and number of teeth per size (M1.6 upward; the M24 column of form A and the M24–M30 headers of form J were dropped for want of values, form V stops at M16 — fuller collection note). | Hardness not stated by this source. | [R6] |
| Serrated lock washer | DIN 6798 A / J / V (withdrawn) | Three forms side by side: Form A external, Form J internal, Form V; minimum number of teeth per size. | Hardness not stated by this source. | [R5] |
| Conical spring washer | DIN 6796 | Conical (spring-disc) form as described by the source; height range with max/min stated per size (collected sheet covers M2–M16). | Hardness not stated by this source. | [R7] |
| Plain and helical lock, inch | ASME B18.21.1 (SAE / USS patterns) | Type A and Type B plain washers and helical spring lock washers by inch size, with inner diameter, outer diameter and thickness limits. | Hardness not stated in the collected tables. | [R8] |
| Square taper washer | DIN 434 | Square washer with an 8% taper angle for U-section and C-section beams; two grooves across the top mark the taper on the reverse. Scope M8–M27 per the two collected distributor pages [R15, R24] — single-type source, no standard text collected. | 100–250 HV 10, stated by three distributor pages on three hosts [R15, R24, R27]; no standard text collected — the hardness class is not confirmed against the standard. | [R15, R24, R25, R27] |
Need a specific washer? See the RFQ fields (§08).
03 · Selection & applications
Four decisions cover most washer RFQs. The last one is a dispute between collected sources, and we show the disagreement instead of picking a convenient side.
Decision 1 — Is the designation on the drawing current, and does the customer accept it?
The usual failure is not a wrong size; it is a current-looking part number for a withdrawn standard. DIN 127 A & B, DIN 128 and DIN 6798 are printed as withdrawn in the collected pages [R3, R4, R5], one standards catalogue (NSAI) shows DIN 127:1987-10 withdrawn on 01-07-1993 — that date is that catalogue's alone [R13] — and a distributor record says the standard was withdrawn without a replacement [R14]. None of those sources names the current replacement in so many words. The buyer's route is to put both facts on the RFQ — the legacy designation the drawing uses and the question of whether the customer requires movement to a current framework — rather than letting the supplier decide silently. Plain washers have their own mapping: DIN 125 has a published equivalent line to DIN EN ISO 7089 in the same source that carries the dimension table, and the ISO equivalents of Type A (7089) and Type B (7090) are stated explicitly [R1, R9, R10].
Decision 2 — Match the washer hardness class to the bolt class, not to the washer size
The ISO flat-washer selection table links the washer hardness class to the product grade of the washer and the property class of the bolt, screw or nut it is used with: parts up to Class 6.8 accept 100 HV, Class 8.8 and Class 9.8/10.9 require 200 HV, and Class 12.9 requires 300 HV [R12]. The DIN standards described on this page print dimensions and nothing on hardness [R1, R2, R3, R5], so size-for-size equivalence tells the buyer nothing about pressure under a high-strength bolt. Put the hardness class on the RFQ as a value, as an ISO class where the drawing uses ISO, and ask for a hardness test on the certificate when the joint carries a high-strength bolt.
Decision 3 — Decide what the joint needs the washer to do before choosing the locked family
Plain, spring-lock, toothed and conical washers are not four grades of the same part; they load and contact the joint differently. A plain washer spreads load [R1]. A DIN 127 ring is a split spring ring with type-specific height limits [R3]. A DIN 6798 serrated washer is a toothed plate whose forms differ in whether the teeth face outward (A) or inward (J) [R5, R22, R23]. A DIN 6796 conical washer is a spring disc loaded in the axial direction by its source's description [R7]. Because the families load and contact the joint in different ways, the designation is part of the joint design. The design decision itself stays with the engineer; the RFQ's job is to carry the right designation.
Decision 4 — Square taper washers are not flat washers with a square outline
A DIN 434 square taper washer has an 8% taper and grooves on top that mark the taper side [R15, R24]. It exists to turn the sloped face of a U-section or C-section beam into a flat bearing surface for the bolt head or nut. Used flat-side down, or substituted by a DIN 436 square washer of the same nominal size, it stops doing that job. Distributor product pages state the hardness range (100–250 HV 10) and the M8–M27 size run [R15, R24, R27]; one of them also lists an M18 size [R27]; none is the standard text, and this page has not checked the figures against it — so hardness is a value to request, not one to assume.
Decision 5 — What holds the thread when the joint vibrates
A split lock washer resists vibration-induced loosening by creating tension between the bolt head and the surface, but its effectiveness varies with the application and it may not prevent loosening entirely; its deflection is very limited, which is the mechanical reason it cannot keep pressing once the joint has relaxed [S3, S22]. The alternatives trade differently, and the choice turns on reusability and temperature rather than on any effectiveness ranking — the collected sources publish no comparative test data ranking spring lock washers against thread lockers, nylon insert nuts or serrated flanges [S3]. Thread patches significantly reduce loosening and are particularly effective in high-vibration applications, but most patched bolts cannot be re-tightened without the patch wearing off [S3]. Thread-locking compounds give vibration resistance without the friction reduction that anti-seize introduces; purple grade allows disassembly while red grade creates a permanent assembly that needs heat for removal [S19]. Nylon insert nuts retain their locking ability up to 121°C and can also help seal the thread against oil, water, petrol and paraffin seepage — beyond that temperature the insert is the wrong device [S17]. A joint that will be serviced repeatedly must not depend on a locking device that dies at the first re-tightening.
Decision 6 — When only a conical washer holds clamp load
A conical spring washer is the family designed for a joint that relaxes. Tightening flattens the cone and it pushes back with a spring force, so when creep or gasket settling opens a gap, the washer expands to take up the slack and keeps pressing — constant-force behaviour neither a flat washer nor a split lock washer can reproduce, because the split ring’s deflection is very limited [S22]. A properly chosen conical washer exerts a preload slightly higher than the desired minimum clamp load, so the spring stays engaged even if the bolt relaxes [S27]. The stakes are the two failure directions of preload itself: too little preload invites vibration loosening, fatigue, joint separation and slip, while too much can yield the bolt or contribute to stress corrosion cracking [S8, S18]. DIN 6796 standardizes conical spring washers for bolted joints and DIN 2093 disc springs more generally, typically heat-treated spring or alloy steel [S27]. What the sources do not give is any load-deflection curve or sizing procedure for a given bolt preload and joint stiffness — the sizing must come from the standard or the supplier, never from this page.
Decision 7 — Electrical isolation holds only until the washer cold-flows
In mixed-material assemblies a non-conductive washer, bushing or gasket breaks the electrical circuit that galvanic corrosion needs — often more effective than changing the fastener alloy alone [S9, S29]. The failure mode to design against is the isolator itself: if the bushing cracks or the washer cold-flows under preload, metal-to-metal contact returns and the galvanic activity resumes, so the isolating part must withstand compression, temperature, UV exposure and chemical contact for the life of the joint [S9]. The added washer also changes the stack-up, which changes clamp load and torque response — the joint must be re-checked, never assumed unchanged [S9]. Two boundaries apply: every dielectric material must be evaluated against the loading condition, and for high-strength structural connections the collected standards’ position is that shims and washers are not allowed there at all [S5].
Decision 8 — Check the material stack, not only the washer
The washer sits inside a material stack, and the stack decides whether the joint corrodes or galls. Same material family with similar hardness carries no galvanic potential and no galling risk; once the materials differ, matching on one number is not enough — A4-80 stainless and Class 8.8 share a nominal 800 MPa tensile figure, but their proof strength, ductility, hardness, friction, galling behaviour and compatible nut and washer requirements can all differ [S11, S25]. Lubricants carry their own prohibitions: copper-based anti-seize must never be used on aluminium components or with zinc-plated fasteners, because it accelerates galvanic corrosion between dissimilar metals; nickel-based formulations prevent galling on stainless without that concern [S19]. And zinc-plated fasteners in contact with modern pressure-treated lumber corrode rapidly — hot-dip galvanized or stainless is the specified alternative there [S23]. Where no washer hardness value relative to the bolt and clamped material is published, that comparison must be made from the standard or the supplier’s data; it cannot be assumed from a size match.
Where the sources disagree — and what would settle each
Neither dispute is resolved by the collected evidence. Each is settled by the joint design or the customer's acceptance, not by a supplier's claim.
| Disputed item | One position | Another position | What the buyer should do |
|---|---|---|---|
| What split spring washers do for a joint | Lock washers resist vibration loosening of fasteners (a reference guide's definition of the type) [R20]. | Split lock washers provide minimal protection once full clamping load is applied and are generally inadequate for high-cycle or safety-critical assemblies [R18]. | Treat the washer as a choice made in the joint design, not as a substitute for a properly designed locking method; ask the engineer which locking route the joint assumes. |
| Whether a spring washer can be tested as the locking feature | A transverse (Junker) test can be performed on the locking mechanism formed by a washer, such as a helical spring lock washer [R16]. | The same washer type is described as losing its spring effect under full clamp load [R18]. | If locking performance matters, ask for a Junker-type test result for the specific assembly rather than the washer family, and state it in the RFQ. |
Use the washer to grow the bearing area — and check thickness where it bends
Washers are used to increase the bearing area under the bolt head and nut, and one collected engineering source adds a condition that matters for procurement: washer thickness is critical when the washer is subjected to bending loads, for example where a joint surface is out of alignment [R17]. That turns thickness from a nominal column into a requirement on the RFQ where the drawing shows a bowed or stepped contact face.
04 · Quality & verification
A washer is one of the cheapest parts in a bolted joint and one of the hardest to tell apart on receipt: several families share a nominal size, and the standards most drawings name state dimensions rather than material or hardness. That is what the buyer has to work around.
How a buyer verifies the declared properties
- Designation against the standard's own title. Check the part number names the form as well as the number (DIN 125 A or B, DIN 127 A or B, DIN 6798 A, J or V) — the forms differ in geometry within one standard number [R1, R3, R5].
- Dimensions against the row. Compare a sample's bore, outside diameter and thickness with the size table of the named standard, using the limit — minimum or maximum — the standard gives for that column [R1, R2, R3, R4, R6, R7, R8].
- Hardness as a measured value. Where the joint uses a Class 8.8 or stronger bolt, require the ISO hardness class [R12] on the RFQ and a hardness reading on the inspection certificate.
- The features that define the form. Number of teeth for DIN 6797 and DIN 6798 and whether they face out or in [R5, R6, R21, R22, R23], the height range for DIN 6796 [R7], the split and height limits for DIN 127 [R3], and the 8% taper and its marking grooves for DIN 434 [R15] — these are what tell two families apart visually.
- Coating. State the finish on the RFQ and have the supplier declare the finish of the delivered lot (the finishes this line quotes are in §05); the finish changes the surface that contacts the joint and is not printed on the standard's dimension table [R1, R2, R3, R5].
- Certificate scope. Ask the supplier which properties the inspection certificate covers — dimensions only, or dimensions plus material and hardness — because for the DIN plain-washer standards on this page, material and hardness are not established by the standard pages themselves [R1, R2].
- The isolating part under load. Where a joint specifies non-conductive washers or bushings, confirm the delivered material is the specified dielectric and check after assembly that the isolator has not cracked or cold-flowed under preload — once metal-to-metal contact returns, the galvanic circuit closes again and the isolation fails silently [S9, S29].
- The locking route named, not implied. If the joint relies on a locking device, record which one the design assumes (split ring, thread patch, nylon insert, thread-locker, serrated bearing face): thread patches cannot be re-tightened without the patch wearing off, nylon insert retention ends at 121°C, and red thread-locker needs heat for removal — a servicing plan that assumes re-tightening fails against three of those four routes [S3, S17, S19].
What justifies rejecting a washer shipment at receiving?
Four failure grounds can be checked without a laboratory, in the same pass as the designation and dimension checks above:
- Wrong family in the box. A split spring ring supplied against a DIN 125 line item — or any lookalike substitution asserted as "equivalent" — is a non-conforming part; the families are not interchangeable and no substitution rule is established by the collected evidence [R1, R2, R3, R5, R9].
- Isolation already compromised. Non-conductive washers delivered with visible cracks, permanent set (cold-flow), or a hardened substitute material fail their function before installation, and the joint will corrode invisibly afterwards; reject rather than "try one" [S9].
- Material stack incompatibility. Copper-based anti-seize present on aluminium-contacting or zinc-plated parts must be rejected at receiving — the combination accelerates galvanic corrosion, and it cannot be undone after assembly [S19]; zinc-plated washers specified into a treated-lumber joint are rejected the same way [S23].
- Coating or finish not as declared. Where the RFQ named a finish and the delivered lot's declared finish differs, the lot is not the quoted part; the finish changes the contact surface and is not visible in the dimension table [R1, R5].
Why a supplier's "equivalent" claim is not verification
Every washer family on this page has a near-lookalike: DIN 125 next to DIN 126, DIN 127 next to DIN 128, DIN 6797 next to DIN 6798, DIN 434 next to any square washer. A supplier's statement that one is "equivalent" to another does not replace the designation on the drawing — the collected evidence does not establish a substitution rule between these families, and the one substitution this page can check by geometry (ISO 7089 / 7090 against DIN 125 A / B) is a published mapping, not a supplier's judgement [R9].
What this page cannot verify
- Hardness or material for the DIN plain, spring-lock, toothed and serrated washers — the collected standard pages state neither [R1, R2, R3, R4, R5].
- The current replacement standard for DIN 127, DIN 128 and DIN 6798 — the sources say withdrawn, not what replaces them [R13, R14].
- Whether a locking washer is adequate for a given joint — the sources disagree and the decision belongs to the joint design [R16, R18, R20].
- Whether a washer shipment's coating complies with a specification's coating requirement — the coating route is stated on the RFQ, not established here.
- Loading (spring rate, compression) values for DIN 6796, DIN 127 and DIN 128 beyond the geometric height data [R3, R4, R7].
- Bearing-stress or contact-pressure values for any washer family here — no collected source publishes them, so contact-face adequacy cannot be computed from this page [S1–S29].
- Load-deflection curves or a sizing procedure for conical spring washers against a target preload — sizing must come from DIN 6796 / DIN 2093 or the supplier, never from this page [S22, S27].
- Comparative effectiveness data ranking locking devices (split ring vs thread patch vs nylon insert vs thread-locker) — the sources describe trade-offs, not test data, so no ranking is published here [S3].
- Washer hardness relative to the bolt and clamped material for the DIN families — no collected source states it, so the comparison must be made from the standard or supplier data, not assumed from a size match [S11, S25].
05 · Manufacturing & supply
The supply facts below are the owner-adjudicated values for this product line, rendered verbatim from the decision record (packs/industrial-fasteners/product-decisions/washers.decision.json). They describe what this supplier can quote; they are not standard values. Where the owner has not adjudicated a fact, it does not appear here.
| Supply fact | Owner-confirmed value (verbatim) | Decision record |
|---|---|---|
| Size range | “Up to M36 / 1-1/2" (36 mm)” | product-catalog.json:products[slug=washers].owner_specs.diameter |
| Standards supplied | “DIN 125 (flat washers type A/B); ISO 7089 / ISO 7090; USS / SAE patterns” | product-catalog.json:products[slug=washers].owner_specs.standard |
| Coating options | “Zinc plated (blue/yellow), Geomet, Dacromet, hot-dip galvanized” | product-catalog.json:products[slug=washers].owner_specs.coating |
| Minimum order quantity | “10000 pieces” | product-catalog.json:products[slug=washers].owner_specs.moq |
| Lead time | “3-7 days (stock)” | product-catalog.json:products[slug=washers].owner_specs.lead_time |
| Indicative price | “USD 0.002-0.01/pc” | product-catalog.json:products[slug=washers].owner_specs.price_from |
06 · SKU specification library
Specification pages for each standard in this cluster, with the per-size dimension table transcribed from the named source.
- DIN 125 plain washers (type A / B)
- ISO 7089 plain washers, normal series
- ISO 7090 chamfered plain washers
- DIN 126 plain washers, normal series
- DIN 433 small-OD plain washers
- DIN 134 plain washers, large series
- DIN 127 / DIN 127 B spring lock washers
- DIN 128 A / 128 B curved spring lock washers
- DIN 6797 toothed lock washers
- DIN 6798 A / J / V serrated lock washers
- DIN 6796 conical spring washers
- SAE flat washers
- USS flat washers
- ASME B18.21.1 Type A / B plain washers (inch)
- ASME B18.21.1 helical spring lock washers (inch)
07 · Buyer questions
My spring washer looks just like a flat washer on the build. Is it a lock washer?
The designation, not the look, decides. DIN 127 is the split spring-ring lock washer and DIN 128 is a separate spring lock washer with forms A and B, while DIN 125 (ISO 7089) and DIN 126 are plain washers [R1, R2, R3, R4]. A tall bore, a split or a spring-and-form marking is what separates the families on the bench; the material alone does not (see §02). A washer swapped into a plain-washer line item, or the reverse, arrives as a non-conforming part even when the size fits. And being a lock washer does not make it right for a critical bolted joint: one collected technical source states that split lock washers provide minimal protection once full clamping load is applied and are generally inadequate for high-cycle or safety-critical assemblies [R18]. For those joints, ask the engineer which locking route the design assumes rather than substituting a washer.
Are DIN 127 and DIN 6798 still valid standards?
Treat them as legacy designations. The collected pages print DIN 127 A & B and DIN 6798 as Withdrawn [R3, R5]; DIN 127:1987-10 carries a withdrawn date of 01-07-1993 in the NSAI standards catalogue [R13]; and a distributor product record states that the DIN 127 B standard was withdrawn without a replacement [R14]. Parts are still bought and stocked under those names, and a drawing that uses them is not automatically wrong — but the RFQ should say whether the customer accepts the legacy designation or needs the current framework (ISO, or company standard) placed beside it [R13, R14].
Can I replace a split spring washer with a serrated (toothed) washer?
Not by default. In the DIN face-to-face series the two are separate standards with different geometry — DIN 127 is the split spring ring, while DIN 6798 runs to forms A, J and V, each stating a minimum number of teeth per size [R3, R5]. Whether the substitution is acceptable depends on what the joint needs the washer to do (hold a preload, resist rotation, protect the contact face) and that is a design decision. Our sources do not establish a substitution rule, so we do not publish one: state both designations on the RFQ if either is acceptable.
Which hardness should a washer have for a Class 10.9 bolt?
For ISO plain washers the hardness class follows the property class of the part it is used with: in the ISO flat-washer selection table, product grades C and A and bolt property classes up to 6.8 accept 100 HV washers, while Class 8.8 and 9.8/10.9 parts require 200 HV, and Class 12.9 requires 300 HV [R12]. The DIN face-to-face standards this page describes do not state hardness at all [R1, R2, R3, R5], so a 100 HV washer quoted under a DIN designation cannot be shown from these sources to be adequate under a Class 10.9 bolt — ask for the hardness class explicitly on the RFQ.
What does a washer quote need to state so two suppliers are comparable?
Family and exact designation (DIN 125 A or B, ISO 7089 or 7090, DIN 127 form A or B, DIN 6798 A/J/V, DIN 6796), nominal size, material and hardness class, coating, quantity and destination, plus the certificate: which properties the inspection certificate actually covers [R1, R2, R3, R5, R6, R7, R12]. A quote that names only "washer M10 steel zinc" is not comparable, because every cell of that description has at least one alternative.
Will a split lock washer actually stop a bolt loosening under vibration?
It cannot be counted on to. A split lock washer works by creating tension between the bolt head and the surface, but its deflection is very limited, so once the joint relaxes it cannot keep pressing, and it may not prevent loosening entirely — effectiveness varies with the application [S3, S22]. The collected sources give no comparative test data ranking it against the alternatives, so no ranking is published here [S3]. What the sources do establish is the trade-off per route: thread patches are particularly effective in high-vibration applications but most cannot be re-tightened without the patch wearing off [S3]; nylon insert nuts hold locking ability only up to 121°C [S17]; purple thread-locker allows disassembly while red creates a permanent assembly needing heat for removal [S19]. If the joint is safety-critical, ask which locking route the design assumes rather than substituting a washer (see §04).
When does a joint need a conical (DIN 6796) washer instead of a spring lock washer?
When the joint relaxes and the lost preload must be recovered. Tightening a conical spring washer flattens the cone and it pushes back with spring force, taking up slack from creep or gasket settling — a properly chosen one exerts a preload slightly higher than the desired minimum clamp load, so the spring stays engaged even if the bolt relaxes [S22, S27]. A split lock washer cannot reproduce this: its deflection is very limited [S22]. The stakes are the two preload failure directions — too little invites vibration loosening, fatigue, joint separation and slip, while too much can yield the bolt or contribute to stress corrosion cracking [S8, S18]. DIN 6796 standardizes these washers for bolted joints, typically in heat-treated spring or alloy steel [S27]. What no collected source gives is a load-deflection curve or sizing procedure for a specific bolt preload and joint stiffness — that must come from the standard or the supplier, never from a product page.
How do I keep a stainless bolt from corroding an aluminium plate?
Break the electrical circuit. A non-conductive washer, bushing or gasket between the dissimilar metals is often more effective than changing the fastener alloy alone [S9, S29]. Three limits apply. First, the isolator itself fails: if it cracks or cold-flows under preload, metal-to-metal contact returns and the galvanic activity resumes — the material must withstand compression, temperature, UV and chemical contact for the life of the joint [S9]. Second, the added washer changes the stack-up, so clamp load and torque response must be re-checked, never assumed unchanged [S9]. Third, chemistry at the contact matters beyond the washer: copper-based anti-seize must never be used on aluminium components or with zinc-plated fasteners because it accelerates galvanic corrosion; nickel-based formulations avoid that concern [S19]. And for high-strength structural connections, shims and washers are not allowed there at all [S5].
08 · RFQ — what to state so quotes are comparable
These fields follow from the decisions above. State, per line item:
- Family and designation — DIN 125 A or B / ISO 7089 or 7090, DIN 126, DIN 434, DIN 127 A or B, DIN 128, DIN 6797, DIN 6798 A, J or V, DIN 6796, ASME B18.21.1 type, SAE or USS; and whether the legacy designation is accepted [R1–R15, R21–R23].
- Nominal size — the thread size the washer fits, plus any outside-diameter or series requirement the drawing sets.
- Material and hardness class — explicitly; 100 / 200 / 300 HV per the ISO table where the drawing uses ISO [R12].
- Coating — the finish, drawn from the finishes quoted for this line (see §05).
- Certificate — which properties the inspection certificate must cover: dimensions, material, hardness, coating.
- Quantity, destination and delivery window — with the supplier's stock position stated as at the quote date.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Washers inquiry
- ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
- ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
- ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
- ✓ Describe the bearing surface or locking function, quantity per size and destination.
- ✓ Factory-direct pricing for your Washers
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support