Zinc Flake Coating

Non-electrolytic zinc flake coating for fasteners per ISO 10683 — dip, spin and cure application, 240–1,000 hours neutral salt spray, no hydrogen embrittlement risk.

Last updated: 2026-11

Request a Quote

Zinc Flake Coating in an industrial setting
Illustrative image redrawn from real Zinc Flake Coating product references — not a photograph of stocked items.

Specifications

Zinc flake is the non-electrolytic alternative to plating: parts are dipped in a zinc-rich liquid, spun to remove excess, and heat-cured. Because no electric current and no hydrogen are involved, it carries no hydrogen-embrittlement risk — the deciding factor for high-strength bolts and spring steels that cannot be safely electroplated. It delivers corrosion resistance in the same class as zinc-nickel, takes lubricated topcoats for controlled torque-tension behavior, and is the standard finish where 240–1,000 hours of salt-spray life is required without plating.

Process Non-electrolytic: dip, spin-off, heat cure
Reference standard ISO 10683:2018 (zinc flake coating systems)
Corrosion resistance 240–1,000 hours neutral salt spray depending on system; example specification GMW3359 Code A at 720 hours
Appearance Gray base coat; black or lubricated topcoats available
Lubrication Lubricant topcoats achieve controlled friction — example COF 0.13 ±0.03 per ISO 16047
Hydrogen embrittlement None — non-electrolytic application, no post-plate bake required
Best suited for High-strength bolts, spring steels, harsh-environment hardware
Salt spray (NSS) — TACOM 12424710 Method 4 700 h — 12 µm — Black
Salt spray (NSS) — GMW3359 Code A 720 h — 12 µm — Grey

Where this grade fits

Zinc flake is applied non-electrolytically, so it generates no plating-bath hydrogen and needs no post-coating bake — above roughly 1000 MPa tensile (about 32 HRC) it is often the only acceptable coating option, and it reaches 500–2,000+ salt-spray hours at 8–20 µm while keeping threads at nominal size. That combination is why the 12.9 and A490 pages point here.

Materials

  • High-strength carbon steel fasteners
  • Spring steel washers and clips
  • Alloy steel fasteners

Ordering & documentation

Documents

Shipments of Zinc Flake Coating are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Zinc Flake Coating orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (Zinc Flake Coating), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for zinc flake coating is per batch, carried with the fastener order (applies to the standard sizes and finishes for zinc flake coating; mixed, special or custom variants are quoted — final commercial terms per quotation) Finishing for zinc flake coating run adds 5–10 days to the fastener lead time. Quantities or variants of zinc flake coating outside the standard range are confirmed at quotation.

Storage & shipping

Coated parts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store finished fasteners dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why choose zinc flake instead of zinc-nickel plating?

The usual reason is hydrogen embrittlement: zinc flake is applied without electrolysis, so hardened high-strength parts carry no embrittlement risk and need no post-plate bake. Corrosion performance is comparable (240–1,000 hours neutral salt spray). Zinc-nickel retains advantages where conductivity, a specific black appearance or an OEM-mandated electroplate spec governs. Specify the finish the drawing calls out; both are delivered through the same coating lines.

What is the MOQ and lead time for this finish?

Finishing runs per batch carried with the fastener order and adds 5–10 days to the fastener lead time. Coated parts follow the finish line that processes them, so confirm the exact schedule against quantity and finish class at quotation.

What should an RFQ for this finish state?

State the base fastener (grade, diameter, length), the coating standard and class (for example ASTM B841 Class 2 with black trivalent passivate, or ISO 10683 with a specified topcoat), any thickness or salt-spray requirement, lubrication or torque-tension needs, and quantity per size — plus destination country and required documents such as a mill test certificate.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Zinc Flake Coating inquiry

  • ✓ Identify the base fastener material/grade and substrate condition before coating.
  • ✓ Name the coating process and governing specification, with required coating thickness and any post-treatment.
  • ✓ Define corrosion acceptance explicitly: test method, exposure duration, and whether white corrosion or red rust is the rejection criterion.
  • ✓ State any friction-coefficient, torque-tension, temperature or hydrogen-embrittlement controls relevant to the joint.
  • ✓ Factory-direct pricing for your Zinc Flake Coating
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.