Surface Finishes & Coatings

A comparison of common steel fastener finishes including zinc flake, phosphate & oil, cadmium electroplate, and zinc electroplate, with their corrosion resistance, friction, and hydrogen embrittlement characteristics.

Last updated: 2026-11

Request a Quote

Surface Finishes & Coatings in an industrial setting
Illustrative image redrawn from real product references — not a photograph of stocked items.

Specifications

Current supplyable range — owner-confirmed scope of supply; requirements outside this range are confirmed per quotation.

moq per batch (carried with fastener order)
lead time +5-10 days per batch (with fastener order)
price from quoted per batch/ton (no unit price published)

Materials

  • steel

Selection guidance

Why finishes are specified, how the common coating systems compare, and what the hot-dip galvanizing standards actually require of an order.

The trade-off: cost versus corrosion resistance

Surface finishes are applied to steel bolts and screws primarily to improve corrosion resistance. Each finish offers a different level of it, and typically the higher the corrosion resistance, the more the finish costs. Resistance is measured with a standard neutral salt spray test (NSS) specified in standards such as ASTM B117 or ISO 9227: parts are exposed to salt spray in a chamber for a stated number of hours, then visually examined.

One manufacturer’s relative comparison of the five finishes it ships most (cost indexed to its own volume; hours are typical NSS ranges) shows the spread: zinc phosphate & oil at index 1 with 2–72 hours; zinc electroplate at 2 with 72–384 hours; zinc-nickel at 6 with ~1000 hours; cadmium at 9 with 72–168 hours; zinc flake at 12 with 240–1000 hours. Treat the cost indexes as order-of-magnitude guidance — they vary with volume — but the hours column is a usable first filter for matching a finish to the environment the fastener will actually see.

The five finishes buyers specify most

Zinc phosphate & oil is a liquid bath chemical conversion process followed by a protective oil. It is the lowest-cost option, gives a thin black coating suitable for handling, packing, storage and everyday dry ambient conditions, slightly increases lubricity, and carries a very low hydrogen-embrittlement risk for hardened parts.

Zinc electroplate is the cathodic deposition of zinc from an ionic solution. It is versatile: thinner coatings suit dry indoor conditions, thicker layers wet outdoor and saline exposure. Its surface is moderately rough, which decreases lubricity relative to plain steel — sealers and lubricants exist to recover both lubricity and corrosion resistance. Its known downside is hydrogen embrittlement on hardened high-strength parts: hydrogen is produced at the steel surface during electroplating, so plating specifications include post-plate baking, which can run 24 hours or more depending on thickness (ASTM B850 is the reference).

Zinc-nickel electroplate consists of an 8–14 µm layer of 12–16% nickel alloy next to the steel, topped with a trivalent passivate and a top coat. It offers corrosion resistance up to 10× conventional zinc plus wear resistance, and has gained popularity as the less-toxic alternative to cadmium that automotive and military vehicle designers are migrating to under new regulations.

Zinc flake is applied non-electrolytically (dip-spin or spray, then cured), so it avoids the plating-bath hydrogen exposure entirely, and reaches 240–1000 salt-spray hours. Cadmium electroplate, once specified extensively on commercial and military fasteners, has been virtually eliminated from commercial products because of its toxicity and removed from new military design; the remaining customer calls it sees are legacy AMS QQ-P-416 requirements.

Hot-dip galvanizing: A153 and F2329 are not interchangeable callouts

Both ASTM A153 and ASTM F2329 govern hot-dip galvanizing of centrifuged hardware — the spin step that keeps threads free of excess zinc. The difference is not the process but the rigor of the quality framework: F2329 was written specifically for fasteners and layers additional requirements on top of an A153-like base. If F2329 is on the order, the lot type must be explicitly stated — batch lot or production lot (with Detection/ Prevention process types under F1470) — because ambiguity defaults the supplier to a fixed sample size and can create certification gaps at delivery.

F2329 adds requirements A153 does not have: mandatory stout-knife adhesion testing on every batch lot (A153 tests only on visible evidence of a problem); higher coating thickness for fasteners and nuts 3/8 inch and under (1.5 mils average vs A153’s 1.4) and, most significantly, for Grade A394 bolts under Supplementary Requirement 1 (2.8 mils average vs 2.1 under A153 Class C); water quenching of all parts unless the customer specifies air cooling; recorded average bath temperature communicated to the customer; and a more complete certification package at delivery.

Two practical notes for buyers. First, appearance: lumpiness, dullness, matte gray areas or minor color non-uniformity are not defects under either standard — rejecting compliant parts on cosmetic variation is a documented field failure mode. Second, embrittlement: both standards prevent it the same two ways (baking after chemical cleaning before galvanizing, or abrasive blasting with flash cleaning), but their embrittlement test methods differ (A143 Paragraph 9 vs F606 wedge), so lab capability should be confirmed before specifying F2329 on high-strength fastener orders.

Thickness classes and the thread-fit bill

Coating thickness is where corrosion protection and thread fit pull against each other. Electroplated zinc is specified by service class (ASTM B633 SC1–SC4 across roughly 5–25 µm), and the passivate counts as much as the microns — the same 12 µm zinc plate moves from around 200–240 salt-spray hours to red rust with a yellow passivate to 480+ hours when a sealer is added. The most commonly cited specification error is ordering an indoor class (SC2, 8 µm) for parts that will see an outdoor, wet environment (SC3): the per-part saving is fractions of a cent against a failure cost orders of magnitude larger.

Hot-dip galvanizing sits five to ten times thicker (roughly 40–60 µm after centrifuging, up to 86 µm on larger diameters), which is why it outlasts electroplate outdoors — and why the thread system changes: hot-dip galvanized threads are feasible from about M8 upward, and coated nuts are re-tapped to oversize 6AZ/6AX tolerance classes to run free on the galvanized bolt. The thin-film systems buy corrosion hours without that bill: zinc-nickel at 8–12 µm reaches 700–1,000 hours to red rust and zinc flake at 8–20 µm reaches 500–2,000+ hours, both while holding original thread tolerances. One caveat carries across every system: the same coating name can hide different alloy, thickness and sealer, so qualify the system, not the label.

How do you verify a coating on delivered fasteners?

Coating verification on hot-dip galvanized hardware runs on three tests - coating thickness, adhesion and appearance - and under F2329 batch-lot inspection the acceptance criterion in all cases is zero defects; there is no allowable-defect count to negotiate. Thickness is measured per ASTM E376, with one geometric rule buyers miss: any article exceeding five feet in length (anchor rods are the common case) must be measured at each end and in the middle, not at one representative point.

The sampling plan depends on the lot type stated on the order. Batch lots (identical parts galvanized in one basket) are sampled as a batch; production lots split into a Detection or Prevention process with sample sizes drawn from ASTM F1470 Table 3 - for example, a lot of 500 articles under the detection process requires testing of 11 samples for coating thickness, 11 for visual appearance, and 3 for adhesion. An order that names F2329 but not the lot type leaves the supplier on a default sample size, which is where certification gaps at delivery come from.

The paperwork is part of the verification: the expectation under F2329 is a more complete certification package that documents lot traceability, bath temperature, test results for thickness, adhesion, and appearance, and any supplementary requirements invoked. What this page cannot verify: the actual thickness, adhesion or appearance of a specific delivered lot - those come from the mill or plater certificate against the sampled lot, and a buyer audit confirms the certificate matches the lot marking on the parts.

How many salt-spray hours does an application actually need?

Start by reading the hours correctly. Salt spray per ASTM B117 / ISO 9227 exposes plated parts to a continuous mist of 5% sodium chloride solution at 35°C (95°F) - it is not a real-world corrosion simulation, it is a comparative performance test for ranking finishes and lots against each other. The pass criterion is hours to first red rust: red corrosion is iron oxide from the steel substrate, so the number measures how long the zinc lasted before it was fully depleted at the weakest point.

Then anchor the requirement to a thickness class instead of a bare number. A specification that reads "zinc plate per ASTM B633" without a service class tells a plater nothing about performance requirements and tells an engineer nothing about what they will actually receive - ASTM B633 SC1 through SC4 map thickness (5 um mild up to 25 um very severe) to expected hours-to-white-rust and hours-to-red-rust windows. Quote the service class and the hours column together on the RFQ.

Hours are an engineered outcome of three specified variables, not a fixed property of "zinc": coating thickness, passivate chemistry, and whether a sealer is applied. At equal thickness, zinc-nickel delivers 3-6x longer salt spray life than standard zinc - and the practical buying lesson is not to blanket-specify the premium coating: the better approach is a mixed specification, zinc-nickel on the parts genuinely exposed to salt, heat, or high-consequence failure, and standard zinc on everything else.

One verification trap: chamber calibration is not automatic. When evaluating salt spray data from a plating vendor, always ask how and how often their chamber is verified - an unverified chamber produces compliance data that cannot be trusted, however impressive the hours look on paper.

Ordering & documentation

Documents

Shipments of Surface Finishes & Coatings are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for this surface finishes & coatings line follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • Base fastener material/grade and substrate condition before coating.
  • Coating process and governing specification, required coating thickness and any post-treatment.
  • Corrosion acceptance criteria: test method, exposure duration, and whether white corrosion or red rust is the rejection criterion.
  • Any friction-coefficient, torque-tension, temperature or hydrogen-embrittlement controls relevant to the joint.

Sample & supply

Minimum order quantity for surface finishes & coatings is per batch, carried with the fastener order (applies to the standard sizes and finishes for surface finishes & coatings; mixed, special or custom variants are quoted — final commercial terms per quotation) Finishing for this family run adds 5–10 days to the fastener lead time. Quantities or variants outside the standard range are confirmed at quotation.

Storage & shipping

Coated parts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store finished fasteners dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Coating processes

Each coating-process page describes a distinct finish route and its controls. Compare the base fastener, process specification, coating thickness, post-treatment, test acceptance criteria and friction requirements; salt-spray hours alone do not predict service life.

Frequently asked questions

Zinc flake or zinc electroplate — how do I choose?

Zinc flake is applied non-electrolytically, so it avoids the hydrogen-embrittlement exposure that electroplating creates on hardened high-strength parts, and it reaches the longer salt-spray ranges. Zinc electroplate is the lower-cost versatile choice for less aggressive exposure. Name the part hardness and the corrosion target (salt-spray hours if specified) on the RFQ and the quote confirms the system.

How many salt-spray hours should I specify?

Hours are a first filter, not a guarantee: published specification requirements range from a few hours for phosphated-and-oiled parts to several hundred for zinc flake and zinc-nickel systems. Specify the environment the fastener will actually see — or the exact standard and thickness class if your drawing names one (for example ASTM B633 or GMW3179) — rather than the highest number available.

What should a coating RFQ state?

The fastener the finish applies to, the coating system or the target corrosion resistance, any governing standard with its thickness class, and the test report you need at delivery (salt spray test reports are among the standard documents). Coatings outside the owner-confirmed list are confirmed at quotation.

Are coating process temperatures the same as service-temperature limits?

No. Post-electroplating treatment or hydrogen-relief baking, zinc-flake coating cure peak-metal temperature, and phosphating-bath temperature describe manufacturing steps; none is, by itself, a continuous or short-term service-temperature rating for the finished coating. Service limits depend on the exact coating chemistry, basecoat, passivation, sealer/topcoat, thickness and fastener substrate. No system-specific service-temperature rating is published for the owner-listed processes here, so confirm continuous and short-term limits with the coating supplier for the exact system and record the applicable technical data sheet. Treat the owner-listed process-temperature figures as process notes only, not product performance limits.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Surface Finishes & Coatings inquiry

  • ✓ Identify the base fastener material/grade and substrate condition before coating.
  • ✓ Name the coating process and governing specification, with required coating thickness and any post-treatment.
  • ✓ Define corrosion acceptance explicitly: test method, exposure duration, and whether white corrosion or red rust is the rejection criterion.
  • ✓ State any friction-coefficient, torque-tension, temperature or hydrogen-embrittlement controls relevant to the joint.
  • ✓ Factory-direct pricing for your Surface Finishes & Coatings
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.