DIN 6799 Retaining Rings for Shafts (E-Clips)

E-shaped retaining rings for shafts per DIN 6799 — the small-shaft snap ring that snaps into a shallow groove with pliers, no circlip pliers needed. The collected table covers shaft diameters 0.8 mm through 30 mm with ring thickness, groove fit n and outside diameter dc per size.

Last updated: 2026-11

Request a Quote

DIN 6799 Retaining Rings for Shafts (E-Clips) in an industrial setting
Illustrative image redrawn from real DIN 6799 Retaining Rings for Shafts (E-Clips) product references — not a photograph of stocked items.

Specifications

The DIN 6799 E-clip is the fastest retaining ring to fit on a small shaft: pushed on axially with pliers, its three prongs spring into a shallow groove and the ring is locked — no circlip pliers, no threaded shoulder. It is the standard axial locating device on small shafts: rollers and bearings, pins, levers, electric motor armatures, actuators. The collected specification table runs shaft diameters 0.8 mm to 30 mm and tabulates the ring section h, the groove fit n and the maximum outside diameter dc per size — the n ladder is the machinist-facing figure, since the groove diameter must land inside its tolerance band for the prongs to grip. Compared with the grooved-shaft DIN 471 ring, the E-clip takes a shallower groove and fits the smallest diameters in the retaining-ring family — the collected series starts at 0.8 mm.

Standard DIN 6799 — retaining rings for shafts, E-type, axial assembly
Shaft size range 0.8 mm through 30 mm nominal shaft diameter (collected table)
Ring section h 0.2 mm (d 0.8) to 2.5 mm (d 30), with max/min tolerances per size
Groove fit n Per-size nominal with max/min band (e.g. d 8 → n 6.52, 6.578/6.462; d 24 → n 21.88, 21.964/21.796) — the groove diameter must land inside the band for the prongs to grip
Outside diameter dc Max 2.25 mm (d 0.8) to 52.6 mm (d 30) per the collected table
Assembly Axial push-on with pliers; shallower groove than DIN 471 — suited to small shafts and low axial loads
MOQ / lead time Not owner-confirmed for this family — confirmed at quotation
DIN 6799 retaining rings for shafts (E-clips) - per-size dimensions (d 0.8 - 30)All dimensions in millimeters; weight per 1000 pieces. Column labels verbatim from the collected table: h (ring section), n, dc (max).
Nominal diameter dh nominal (mm)h max (mm)h min (mm)n nominal (mm)n max (mm)n min (mm)dc max (mm)Weight (kg / 1000 pcs)
0.80.20.220.180.580.620.542.250.003
1.20.30.320.281.011.050.973.250.009
1.50.40.420.381.281.321.244.250.021
1.90.50.520.481.611.651.574.80.04
2.30.60.620.581.941.981.96.30.069
3.20.60.620.582.72.742.667.30.088
40.70.720.683.343.3883.2929.30.158
50.70.720.684.114.1584.06211.30.236
60.70.720.685.265.3085.21212.30.255
70.90.920.885.845.8885.79214.30.474
811.030.976.526.5786.46216.30.66
91.11.131.077.637.6887.57218.81.09
101.21.231.178.328.3788.26220.41.25
121.31.331.2710.4510.5210.3823.41.63
151.51.531.4712.6112.6812.5429.43.37
191.751.781.7215.9215.9915.8537.66.42
2422.031.9721.8821.96421.79644.68.55
302.52.532.4725.825.88425.71652.613.5

Materials

  • Material per RFQ — the collected specification table covers geometry only

Ordering & documentation

Documents

Shipments of DIN 6799 Retaining Rings for Shafts (E-Clips) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 6799 Retaining Rings for Shafts (E-Clips) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 6799 Retaining Rings for Shafts (E-Clips)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for din 6799 retaining rings for shafts (e-clips) are confirmed at quotation — send ring type, shaft or housing diameter and groove dimensions on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

DIN 6799 Retaining Rings for Shafts (E-Clips) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 6799 retaining rings for shafts (e-clips) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

E-clip (DIN 6799) or external circlip (DIN 471)?

Both locate a component axially on a shaft, but they are different tools. The DIN 6799 E-clip pushes on axially with plain pliers, sits in a shallow groove, and covers the smallest shafts — the collected series starts at 0.8 mm, where circlip pliers would be impossible. The DIN 471 external ring grips with a deeper, more substantial section and carries higher axial loads on larger shafts. So: small shafts, quick assembly, moderate loads — the E-clip; larger diameters and heavier axial thrust — the DIN 471. The groove in either case must land inside the standard’s tolerance band for the ring to grip.

What should an RFQ for DIN 6799 E-clips state?

State the shaft nominal diameter (which selects the ring size), the material and finish required for the environment, the groove diameter your drawing machines (it must fall inside the standard’s n max/min band for that size), the axial load the ring must carry, and quantity per size. Commercial terms are confirmed at quotation.

Which documents can I request with an order of DIN 6799 Retaining Rings for Shafts (E-Clips)?

Orders can be documented with a mill test certificate (MTC), a dimensional report and a salt spray test report, with full batch traceability from raw material to finished product; availability of each document for this designation is confirmed at quotation.

What should an RFQ for DIN 6799 Retaining Rings for Shafts (E-Clips) state?

State the full designation (DIN 6799), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 6799 Retaining Rings for Shafts (E-Clips) inquiry

  • ✓ Identify external shaft rings (for example DIN 471) or internal bore rings (for example DIN 472), plus ring type.
  • ✓ Give nominal shaft or housing-bore diameter and the groove diameter, width and tolerances.
  • ✓ State ring material, heat treatment and finish for the service environment.
  • ✓ Describe axial load, rotational speed, assembly access/pliers and quantity per size.
  • ✓ Factory-direct pricing for your DIN 6799 Retaining Rings for Shafts (E-Clips)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.