E-Rings for Shafts, Heavy Duty (Series 2144–5144)

Heavy-duty E-type retaining rings for shafts, series 2144–5144 — three-point contact rings for grooves machined only partway around the shaft — with the collected 11-size table (rings 9 to 56): d2, d3, s, dg, d1, m, n and the source’s six supplementary columns.

Last updated: 2026-11

Request a Quote

E-Rings for Shafts, Heavy Duty (Series 2144–5144) in an industrial setting
Illustrative image redrawn from real E-Rings for Shafts, Heavy Duty (Series 2144–5144) product references — not a photograph of stocked items.

Specifications

An E-ring is a three-pronged retaining ring that snaps into a short groove cut into one side of a shaft — not a full circle, so the shaft does not need a complete circumferential groove. The heavy-duty 2144–5144 series carries deeper grooves and higher loads than standard E-rings, at the cost of a deeper prong. The collected table lists rings 9 through 56 — 11 sizes — with d2 (plus per-size tolerance), d3 reference, s, dg, d1, m (plus tolerance), n min. and six supplementary columns under their printed labels. The collected page header prints "All measurements in millimeters (mm)", yet the value scale and the 2144–5144 series numbering follow the imperial retaining-ring convention; every figure below is reproduced exactly as printed and the unit question should be confirmed at quotation.

Standard / series E-rings for shafts, heavy duty, series 2144–5144 (collected table covers rings 9–56)
Working principle Three-prong external ring snapped into a partial (non-circumferential) shaft groove; plier or push-on installation
Units note Collected header prints millimeters while the value scale follows the imperial series convention — figures rendered as printed; confirm at quotation
Column labels FN Lbr. / Fs Lbr. / g / Fsg Lib. / nabl min. / lbs reproduced as printed — the collected table carries no unit legend
Row, ring 1 ring 9 | d2 0.074 +0.002/-0.000 | d3 ref. 0.206 | s 0.015 +0.002/-0.002 | dg 0.072 +0.001/-0.003 | d1 0.094 | m 0.020 +0.002/-0.000 | n min. 0.020 | FN Lbr. 13 | Fs Lbr. 51 | g 0.033 | Fsg Lib. 50 | nabl min. 90000 | lbs 0.073
Row, ring 2 ring 12 | d2 0.095 +0.002/-0.000 | d3 ref. 0.270 | s 0.015 +0.002/-0.002 | dg 0.093 +0.001/-0.003 | d1 0.125 | m 0.020 +0.002/-0.000 | n min. 0.030 | FN Lbr. 25 | Fs Lbr. 76 | g 0.033 | Fsg Lib. 75 | nabl min. 70000 | lbs 0.125
Row, ring 3 ring 15 | d2 0.116 +0.002/-0.000 | d3 ref. 0.335 | s 0.025 +0.002/-0.002 | dg 0.113 +0.002/-0.003 | d1 0.156 | m 0.029 +0.003/-0.000 | n min. 0.040 | FN Lbr. 40 | Fs Lbr. 152 | g 0.050 | Fsg Lib. 150 | nabl min. 60000 | lbs 0.308
Row, ring 4 ring 18 | d2 0.147 +0.002/-0.000 | d3 ref. 0.375 | s 0.025 +0.002/-0.002 | dg 0.143 +0.003/-0.003 | d1 0.188 | m 0.029 +0.003/-0.000 | n min. 0.040 | FN Lbr. 50 | Fs Lbr. 183 | g 0.050 | Fsg Lib. 180 | nabl min. 50000 | lbs 0.396
Row, ring 5 ring 21 | d2 0.188 +0.002/-0.002 | d3 ref. 0.446 | s 0.025 +0.002/-0.002 | dg 0.182 +0.003/-0.003 | d1 0.219 | m 0.029 +0.003/-0.000 | n min. 0.031 | FN Lbr. 50 | Fs Lbr. 223 | g 0.050 | Fsg Lib. 220 | nabl min. 43000 | lbs 0.506
Row, ring 6 ring 25 | d2 0.210 +0.002/-0.002 | d3 ref. 0.516 | s 0.025 +0.002/-0.002 | dg 0.204 +0.003/-0.003 | d1 0.250 | m 0.029 +0.003/-0.000 | n min. 0.040 | FN Lbr. 75 | Fs Lbr. 254 | g 0.050 | Fsg Lib. 250 | nabl min. 38000 | lbs 0.704
Row, ring 7 ring 31 | d2 0.250 +0.003/-0.003 | d3 ref. 0.588 | s 0.025 +0.002/-0.002 | dg 0.242 +0.003/-0.003 | d1 0.312 | m 0.029 +0.003/-0.000 | n min. 0.062 | FN Lbr. 135 | Fs Lbr. 305 | g 0.055 | Fsg Lib. 300 | nabl min. 32000 | lbs 0.915
Row, ring 8 ring 37 | d2 0.303 +0.003/-0.003 | d3 ref. 0.660 | s 0.035 +0.002/-0.002 | dg 0.292 +0.004/-0.004 | d1 0.375 | m 0.039 +0.003/-0.000 | n min. 0.072 | FN Lbr. 190 | Fs Lbr. 528 | g 0.055 | Fsg Lib. 520 | nabl min. 28000 | lbs 1.525
Row, ring 9 ring 43 | d2 0.343 +0.003/-0.003 | d3 ref. 0.746 | s 0.035 +0.00/-0.002 | dg 0.332 +0.004/-0.004 | d1 0.438 | m 0.039 +0.003/-0.000 | n min. 0.094 | FN Lbr. 285 | Fs Lbr. 609 | g 0.055 | Fsg Lib. 600 | nabl min. 24000 | lbs 2.024
Row, ring 10 ring 50 | d2 0.396 +0.003/-0.003 | d3 ref. 0.810 | s 0.042 +0.002/-0.002 | dg 0.385 +0.004/-0.004 | d1 0.500 | m 0.046 +0.003/-0.000 | n min. 0.104 | FN Lbr. 360 | Fs Lbr. 832 | g 0.060 | Fsg Lib. 820 | nabl min. 20000 | lbs 2.640
Row, ring 11 ring 56 | d2 0.437 +0.003/-0.003 | d3 ref. 0.870 | s 0.042 +0.002/-0.002 | dg 0.430 +0.004/-0.004 | d1 0.562 | m 0.046 +0.003/-0.000 | n min. 0.124 | FN Lbr. 480 | Fs Lbr. 944 | g 0.060 | Fsg Lib. 930 | nabl min. 17000 | lbs 2.904
Materials / finish Not printed by the collected specification — per RFQ
MOQ / lead time Not owner-confirmed for this family — confirmed at quotation
  • Unit conflict (source-level, verified against the collected page): the source header prints "All measurements in millimeters (mm)" while every value follows the imperial retaining-ring convention — the 2144–5144 series numbering, the decimal-inch value scale and the supplementary load columns match the inch-series ring tables elsewhere in the same source programme. All figures are reproduced exactly as printed with no conversion; treat the dimensional columns as inch values and confirm units at quotation.

Materials

  • Not printed by the collected specification — per RFQ

Ordering & documentation

Documents

Shipments of E-Rings for Shafts, Heavy Duty (Series 2144–5144) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for E-Rings for Shafts, Heavy Duty (Series 2144–5144) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (E-Rings for Shafts, Heavy Duty (Series 2144–5144)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for e-rings for shafts, heavy duty (series 2144–5144) are confirmed at quotation — send ring type, shaft or housing diameter and groove dimensions on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

E-Rings for Shafts, Heavy Duty (Series 2144–5144) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store e-rings for shafts, heavy duty (series 2144–5144) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why choose an E-ring over a conventional circlip?

Groove access and shaft strength. The three prongs need only a short groove, so the ring can be installed after assembly, on shafts already seated in bearings or housings, and the shaft keeps most of its section intact. The penalty is load capacity concentrated at three contact points — fine for locating bearings, gears and idlers, not for heavy continuous thrust. Size by shaft diameter against the collected table’s d2 groove column and confirm the thrust figure for your condition at quotation.

Which documents can I request with an order of E-Rings for Shafts, Heavy Duty (Series 2144–5144)?

Orders can be documented with a mill test certificate (MTC), a dimensional report and a salt spray test report, with full batch traceability from raw material to finished product; availability of each document for this designation is confirmed at quotation.

What should an RFQ for E-Rings for Shafts, Heavy Duty (Series 2144–5144) state?

State the full designation (E-Rings for Shafts, Heavy Duty (Series 2144–5144)), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your E-Rings for Shafts, Heavy Duty (Series 2144–5144) inquiry

  • ✓ Identify external shaft rings (for example DIN 471) or internal bore rings (for example DIN 472), plus ring type.
  • ✓ Give nominal shaft or housing-bore diameter and the groove diameter, width and tolerances.
  • ✓ State ring material, heat treatment and finish for the service environment.
  • ✓ Describe axial load, rotational speed, assembly access/pliers and quantity per size.
  • ✓ Factory-direct pricing for your E-Rings for Shafts, Heavy Duty (Series 2144–5144)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.