Internal Self-Locking Retaining Rings — Thrust Load (Inch Series)

Internal self-locking retaining rings for inch housings 5/16 to 1-1/2 in: ring thickness, ring diameter, margin and static thrust load per housing bore — the grooveless retaining ladder for bores.

Last updated: 2026-11

Request a Quote

Internal Self-Locking Retaining Rings — Thrust Load (Inch Series) in an industrial setting
Illustrative image redrawn from real Internal Self-Locking Retaining Rings — Thrust Load (Inch Series) product references — not a photograph of stocked items.

Specifications

The internal counterpart of the push-on shaft ring springs into a plain bore and holds by tension — no groove machining in the housing. The collected ladder runs housing bores 0.311-0.313 through 1.498-1.502 in: thickness 0.010 in through the 0.627 size, 0.015 from 0.748 up, ring diameter D from 0.136 up to 1.188 in (the ring sits inside the bore, so its free diameter is smaller than the housing), margin E again 0.040/0.060 by thickness, and static thrust loads of a different character than the external series — 80 lb at the smallest bore, stepping down to 45-50 lb mid-ladder, then 75/70/60 lb on the 0.015 rings. The non-monotonic load column is the collected page's own data: thinner rings at small bores carry more static thrust than at mid bores because the load scales with ring section relative to circumference, and the table prints it as measured, not smoothed. Applications are the plastic-housing, die-cast and sheet-metal-bore cases where cutting a groove would cost the housing its integrity — and where the 45-80 lb static ceiling is comfortably above the axial load a light mechanism sees.

Series / scope Internal self-locking retaining rings, inch housing bores 0.311 to 1.502 in — ring dimensions and static thrust load per bore size band (Min./Max. D)
Ring thickness T 0.010 in through the 0.627 bore, 0.015 in from 0.748 up — as printed
Ring diameter D / margin E D 0.136 (0.311 bore) to 1.188 (1.500 bore); E 0.040 on 0.010 rings, 0.060 on 0.015 rings
Static thrust load 80 lb at 5/16 bore, 75/70/60/50/45 stepping down through 0.627, then 75 (0.748), 70, 70, 70 (1.000), 60 (1.250-1.500) — the non-monotonic ladder as printed
Not tabulated Grooved internal rings (DIN 472 / inch grooved identities), housing material limits, material/tempers — per RFQ
Internal self-locking retaining rings, inch series — ring dimensions and static thrust load by housing diameterDimensions in inches; static thrust load in lb. Stacked headers carried verbatim (Min./Max. D split under Housing).
HousingRing DimensionsStatic Thrust Load (lb)
Min. DMax. DThick. TDia DMargin EGroove
0.3110.3130.0100.1360.04080
0.3740.3760.0100.1750.04075
0.4370.4390.0100.2370.04070
0.4980.5020.0100.2580.04060
0.5600.5640.0100.3120.04050
0.6230.6270.0100.3900.04045
0.7480.7520.0150.5000.06075
0.8730.8770.0150.6250.06070
0.9360.9400.0150.6870.06070
0.9981.0020.0150.7500.06070
1.2481.2520.0150.9380.06060
1.4361.4400.0151.1170.06060
1.4981.5020.0151.1880.06060

Materials

  • Spring-temper carbon or stainless, installed expanded into the bore; the thrust figures assume a plain bore of the tabulated diameter in a housing that does not relax under ring pressure — soft plastics may need a heavier ring or a different retaining method. Specify material and bore tolerance on the RFQ; the collected page carries dimensions and static load only

Ordering & documentation

Documents

Shipments of Internal Self-Locking Retaining Rings — Thrust Load (Inch Series) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Internal Self-Locking Retaining Rings — Thrust Load (Inch Series) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (Internal Self-Locking Retaining Rings — Thrust Load (Inch Series)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for internal self-locking retaining rings — thrust load (inch series) are confirmed at quotation — send ring type, shaft or housing diameter and groove dimensions on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

Internal Self-Locking Retaining Rings — Thrust Load (Inch Series) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store internal self-locking retaining rings — thrust load (inch series) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why does the thrust column go down then back up across the size ladder?

Because two effects pull against each other and the collected table prints the net result. Thrust capacity scales with ring cross-section relative to its circumference: at the smallest bores the 0.010 ring is proportionally stout (80 lb at 5/16), mid-bores dilute the same strip around more circumference (down to 45 lb at 0.627), and from 0.748 the strip steps to 0.015 in — the thicker section lifts the rating back to 75/70 before the circumference catches up again and it settles at 60 lb by 1-1/4 to 1-1/2. It is measured data, not a smoothing error, and the practical read is not to interpolate: a 0.62 bore ring is rated 45 lb while the 0.75 bore ring next to it is rated 75. Check the exact bore row against the ladder and keep the application's static load — plus shock allowance — under the printed figure.

How does an internal self-locking ring stay in a bore without a groove?

On radial spring force. The ring is installed expanded (internal rings are wound to a free diameter smaller than the bore) and the resulting outward push generates friction and a light axial bite against the bore wall — enough for the 45-80 lb static ratings on this ladder in a housing that holds its dimensions. That assumption is the series' weak point: a soft plastic bore that cold-flows under ring pressure, or a bore at the loose end of its tolerance, can let the ring spin or walk. The collected page gives geometry and static load, not housing-material guidance, so treat soft housings as an engineering question — and where the load, shock or housing softness exceeds what the ladder supports, the grooved internal ring (DIN 472 and the inch grooved identities) is the retaining method that actually anchors into the part.

Which documents can I request with an order of Internal Self-Locking Retaining Rings — Thrust Load (Inch Series)?

Orders can be documented with a mill test certificate (MTC), a dimensional report and a salt spray test report, with full batch traceability from raw material to finished product; availability of each document for this designation is confirmed at quotation.

What should an RFQ for Internal Self-Locking Retaining Rings — Thrust Load (Inch Series) state?

State the full designation (Internal Self-Locking Retaining Rings — Thrust Load (Inch Series)), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Internal Self-Locking Retaining Rings — Thrust Load (Inch Series) inquiry

  • ✓ Identify external shaft rings (for example DIN 471) or internal bore rings (for example DIN 472), plus ring type.
  • ✓ Give nominal shaft or housing-bore diameter and the groove diameter, width and tolerances.
  • ✓ State ring material, heat treatment and finish for the service environment.
  • ✓ Describe axial load, rotational speed, assembly access/pliers and quantity per size.
  • ✓ Factory-direct pricing for your Internal Self-Locking Retaining Rings — Thrust Load (Inch Series)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.