External Inverted Retaining Rings

External inverted retaining rings — circlips whose lugs are inverted so the assembly sits flush and needs no groove clearance on the loaded face — with the collected 8-size table (rings 50 to 81): d1, s, d3, b, c, d5, d2, m, n, the source’s load columns and the plier tool designation.

Last updated: 2026-11

Request a Quote

External Inverted Retaining Rings in an industrial setting
Illustrative image redrawn from real External Inverted Retaining Rings product references — not a photograph of stocked items.

Specifications

An inverted external retaining ring is an external circlip turned lugs-inward: the installed ring presents a low, flush profile because the lug and plier clearance sit on the unloaded side. That makes it the choice where a conventional external ring’s protruding lugs would foul a mating part, a housing wall or a rotating member. The collected table lists rings 50 through 81 — 8 sizes — with d1, s, d3, b, c, d5, groove d2, m, n, the supplementary load columns (FN, FR, g, FRg, nabl, lbs) and the tool column (A0/A01 across the range). The collected page header prints "All measurements in millimeters (mm)", yet the value scale and the 2100-series-compatible ring numbering follow the imperial retaining-ring convention; every figure below is reproduced exactly as printed and the unit question should be confirmed at quotation.

Type External inverted retaining rings (collected table covers rings 50–81)
Working principle External circlip with inverted lugs for a low flush installed profile; plier installation
Units note Collected header prints millimeters while the value scale follows the imperial series convention — figures rendered as printed; confirm at quotation
Installation tooling Source tool column prints A0 / A01 for every tabulated size
Row, ring 1 ring 50 | d1 0.500 | s 0.035 +0.002/-0.002 | d3 0.461 +0.005/-0.010 | b 0.080 +0.004/-0.004 | c 0.041 +0.004/-0.004 | d5 0.042 +0.010/-0.002 | d2 0.468 +0.002/-0.002 | m 0.039 +0.003/-0.000 | n 0.048 | FN 280 | FR 1117 | g 0.032 | FRg 680 | nabl 40000 | lbs 1.000 | tool A0 / A01
Row, ring 2 ring 56 | d1 0.562 | s 0.035 +0.002/-0.002 | d3 0.521 +0.005/-0.010 | b 0.088 +0.004/-0.004 | c 0.043 +0.004/-0.004 | d5 0.042 +0.010/-0.002 | d2 0.530 +0.002/-0.002 | m 0.039 +0.003/-0.000 | n 0.048 | FN 320 | FR 1269 | g 0.036 | FRg 680 | nabl 35000 | lbs 1.400 | tool A0 / A01
Row, ring 3 ring 59 | d1 0.594 | s 0.035 +0.002/-0.002 | d3 0.550 +0.005/-0.010 | b 0.092 +0.004/-0.004 | c 0.046 +0.004/-0.004 | d5 0.042 +0.010/-0.002 | d2 0.559 +0.003/-0.003 | m 0.039 +0.003/-0.000 | n 0.052 | FN 370 | FR 1320 | g 0.037 | FRg 680 | nabl 32000 | lbs 1.600 | tool A0 / A01
Row, ring 4 ring 62 | d1 0.625 | s 0.035 +0.002/-0.002 | d3 0.579 +0.005/-0.010 | b 0.096 +0.004/-0.004 | c 0.048 +0.004/-0.004 | d5 0.042 +0.010/-0.002 | d2 0.588 +0.003/-0.003 | m 0.039 +0.003/-0.000 | n 0.055 | FN 400 | FR 1421 | g 0.039 | FRg 680 | nabl 30000 | lbs 1.600 | tool A0 / A01
Row, ring 5 ring 68 | d1 0.688 | s 0.042 +0.002/-0.002 | d3 0.635 +0.005/-0.010 | b 0.104 +0.005/-0.005 | c 0.052 +0.005/-0.005 | d5 0.042 +0.010/-0.002 | d2 0.646 +0.003/-0.003 | m 0.046 +0.003/-0.000 | n 0.063 | FN 500 | FR 2335 | g 0.042 | FRg 1000 | nabl 28000 | lbs 2.500 | tool A0 / A01
Row, ring 6 ring 75 | d1 0.750 | s 0.042 +0.002/-0.002 | d3 0.693 +0.005/-0.010 | b 0.112 +0.005/-0.005 | c 0.056 +0.005/-0.005 | d5 0.042 +0.010/-0.002 | d2 0.704 +0.003/-0.003 | m 0.046 +0.003/-0.000 | n 0.069 | FN 600 | FR 2538 | g 0.045 | FRg 1000 | nabl 26500 | lbs 2.800 | tool A0 / A01
Row, ring 7 ring 78 | d1 0.781 | s 0.042 +0.002/-0.002 | d3 0.722 +0.005/-0.010 | b 0.116 +0.005/-0.005 | c 0.057 +0.005/-0.005 | d5 0.042 +0.010/-0.002 | d2 0.733 +0.003/-0.003 | m 0.046 +0.003/-0.000 | n 0.072 | FN 650 | FR 2639 | g 0.046 | FRg 1000 | nabl 25500 | lbs 3.100 | tool A0 / A01
Row, ring 8 ring 81 | d1 0.812 | s 0.042 +0.002/-0.002 | d3 0.751 +0.005/-0.010 | b 0.120 +0.005/-0.005 | c 0.060 +0.005/-0.005 | d5 0.050 +0.010/-0.002 | d2 0.762 +0.003/-0.003 | m 0.046 +0.003/-0.000 | n 0.075 | FN 700 | FR 2690 | g 0.048 | FRg 1000 | nabl 24500 | lbs 3.300 | tool A0 / A01
Materials / finish Not printed by the collected specification — per RFQ
MOQ / lead time Not owner-confirmed for this family — confirmed at quotation
  • Unit conflict (source-level, verified against the collected page): the source header prints "All measurements in millimeters (mm)" while every value follows the imperial retaining-ring convention — the 2100-series-compatible ring numbering, the decimal-inch value scale and the supplementary load columns match the inch-series ring tables elsewhere in the same source programme. All figures are reproduced exactly as printed with no conversion; treat the dimensional columns as inch values and confirm units at quotation.

Materials

  • Not printed by the collected specification — per RFQ

Ordering & documentation

Documents

Shipments of External Inverted Retaining Rings are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for External Inverted Retaining Rings orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (External Inverted Retaining Rings), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for external inverted retaining rings are confirmed at quotation — send ring type, shaft or housing diameter and groove dimensions on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

External Inverted Retaining Rings are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store external inverted retaining rings dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

When does the inverted profile matter?

When anything sits close to the ring. A conventional external ring’s lugs and the plier nose clearance stand proud of the shaft; next to a shoulder, a seal, or inside a housing bore those protrusions foul. The inverted ring turns the lugs toward the shaft so the installed height drops and the loaded face runs flush — the geometry the collected table tabulates (c and d5 columns) is what buys that clearance. Check the mating envelope on your drawing against the d3/b/c figures before choosing it over a standard 2100-series ring.

Which documents can I request with an order of External Inverted Retaining Rings?

Orders can be documented with a mill test certificate (MTC), a dimensional report and a salt spray test report, with full batch traceability from raw material to finished product; availability of each document for this designation is confirmed at quotation.

What should an RFQ for External Inverted Retaining Rings state?

State the full designation (External Inverted Retaining Rings), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your External Inverted Retaining Rings inquiry

  • ✓ Identify external shaft rings (for example DIN 471) or internal bore rings (for example DIN 472), plus ring type.
  • ✓ Give nominal shaft or housing-bore diameter and the groove diameter, width and tolerances.
  • ✓ State ring material, heat treatment and finish for the service environment.
  • ✓ Describe axial load, rotational speed, assembly access/pliers and quantity per size.
  • ✓ Factory-direct pricing for your External Inverted Retaining Rings
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.