H / HNL High Pushout Self-Clinching Nuts

High pushout self-clinching nuts — H non-locking and HNL self-locking (prevailing torque) — for steel sheets HRB 80 or less (H) and HRB 60 or less (HNL), with conformance to IFI 100/107 Grade B and ANSI B18.16.1M prevailing-torque requirements.

Last updated: 2026-11

Request a Quote

H / HNL High Pushout Self-Clinching Nuts in an industrial setting
Illustrative image redrawn from real H / HNL High Pushout Self-Clinching Nuts product references — not a photograph of stocked items.

Specifications

The H series is the high-pushout variant of the clinching nut: where a standard S nut is specified by its installation performance, H is built so the clinch resists higher pushout loads and higher torque-out once it is in the sheet — the two failure modes that matter when a mounted nut will see repeated service tightening. The HNL variant adds a self-locking (prevailing-torque) thread on the same clinch. The collected bulletin states H nuts meet prevailing torque requirements for IFI 100/107 Grade B (unified) and ANSI B18.16.1M (metric), and that HNL head projections may flatten during installation without harm to self-locking or self-clinching performance — a useful practical note for tight squeeze cycles. H is rated for sheets of HRB 80 (HB 150) or less; HNL for HRB 60 (HB 107) or less. The geometry runs a thick single-shank ladder — shank and minimum sheet are both 1.48 mm metric (.058 in. unified) across the tabulated M6–M10 / 1/4-20–3/8-16 range — and the performance table samples H at M10: 22 kN installation, 1760 N pushout, 21.5 N·m torque-out in 2.29 mm 5052-H34 aluminum, 33 kN / 2020 N / 27.1 N·m in 2.24 mm cold-rolled steel.

Type H: non-locking clinch nut with high pushout and torque-out resistance; HNL: self-locking (prevailing-torque) variant
Standards conformance Meets prevailing torque requirements of IFI 100/107 Grade B (unified) and ANSI B18.16.1M (metric), as stated in the collected bulletin
Unified sizes (type availability in collected table) .250-20, .312-18, .375-16; HNL available in all three; H also listed at .375-16
Metric sizes (type availability in collected table) M6, M8, M10; HNL available in all three; H also listed at M10
Shank A max / minimum sheet thickness Unified: .058 in. shank into .058 in. minimum sheet across .250-20 to .375-16; metric: 1.48 mm shank into 1.48 mm minimum sheet across M6 to M10 (single-shank ladder — no code ladder in the collected table)
Hole diameter (sampled, max / min) 1/4-20: .344 / .343 in.; 5/16-18: .413 / .412; 3/8-16: .500 / .499; M6: 8.75 / 8.72 mm; M8: 10.5 / 10.47; M10: 12.7 / 12.67
Head C / E, sampled 1/4-20: .500 / .189 in.; 3/8-16: .650 / .300; M6: 12.7 / 5 mm; M10: 16.5 / 7.9 — head-height (T) columns are not cleanly aligned in the text layer and stay unrendered
Performance (sampled, H at M10 / .375-16) 2.29 mm 5052-H34 aluminum sheet: 22 kN installation, 1760 N pushout, 21.5 N·m torque-out; 2.24 mm cold-rolled steel (.088 in.): 33 kN (7400 lbs), 2020 N (460 lbs), 27.1 N·m (240 in.-lbs) (collected CL performance table)
Panel limits H: sheets HRB 80 / HB 150 or less; HNL: sheets HRB 60 / HB 107 or less
Installation note HNL head projections may flatten during installation without harm to self-locking or self-clinching performance
MOQ / lead time Not owner-confirmed for this family — confirmed at quotation
H nuts - performance data (HNL is not printed in the collected performance table)Values as printed in the collected CL self-clinching performance data (installation force, pushout, torque-out); "collected" wording covers the tenant-internal provenance, which is not rendered. Pushout is tested from the grip side, torque-out from the head side, per the same bulletin. The collected performance table prints only type H; the sampled H cells already on this page are these same rows. HNL performance values are confirmed with the tenant at quotation.
TypeThreadTest sheetInstallation forcePushoutTorque-out
H.375-16 (3/8-16).090 in. 5052-H34 aluminum4900 lbs380 lbs190 in.-lbs
H.375-16 (3/8-16).088 in. cold-rolled steel7400 lbs460 lbs240 in.-lbs
HM10 x 1.52.29 mm 5052-H34 aluminum22 kN1760 N21.5 N·m
HM10 x 1.52.24 mm cold-rolled steel33 kN2020 N27.1 N·m

Materials

  • Per RFQ — the collected bulletin section covers type availability and conformance; material/finish codes were not tabulated in the extracted text layer

Ordering & documentation

Documents

Shipments of H / HNL High Pushout Self-Clinching Nuts are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for H / HNL High Pushout Self-Clinching Nuts orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (H / HNL High Pushout Self-Clinching Nuts), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for h / hnl high pushout self-clinching nuts are confirmed at quotation — send series, thread size and parent sheet thickness on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

H / HNL High Pushout Self-Clinching Nuts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store h / hnl high pushout self-clinching nuts dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

When is an H nut the right choice over a standard S clinch nut?

When the mounted nut will be tightened repeatedly in service. Pushout is the axial force that can drive the clinch back out of the sheet and torque-out is the rotation resistance of the installed nut — H is specified for higher values of both, so joints with frequent service tightening, heavy accessories, or high installed-torque requirements are the natural fit. HNL adds a self-locking thread to the same clinch when the joint also has to hold without clamp load. Note the panel hardness split: the collected bulletin rates H for HRB 80 or less but HNL only for HRB 60 or less, so the softer-panel constraint applies if you need the locking variant.

What does IFI 100/107 Grade B conformance actually buy me?

It means the prevailing-torque performance of the locking variants is held to a published, testable standard rather than a manufacturer-internal number — IFI 100/107 for unified threads and ANSI B18.16.1M for metric, at Grade B in both. For a design review or a customer spec that references those standards, an HNL selection maps to a documented requirement instead of requiring a custom test. The collected bulletin states the conformance claim; the grade-specific torque values themselves live in the standards, not in this page.

What should an RFQ for these self-clinching standoffs state?

State the series (CFSO steel, CFSOS stainless, or CFSOA aluminum), thread size (for example #10-32 or M4 x 0.7), body size (small or large), nominal length L, sheet material, thickness and hardness, and quantity per size — plus destination country. Commercial terms are confirmed at quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your H / HNL High Pushout Self-Clinching Nuts inquiry

  • ✓ Identify the clinch-nut, stud or standoff series and the internal thread size.
  • ✓ Specify parent-sheet material, hardness and actual thickness, not gauge alone.
  • ✓ Provide prepared-hole diameter, edge distance and hole-to-hole spacing from the panel drawing.
  • ✓ State locking/non-locking requirement, installation press/tooling and any push-out or torque-out acceptance data.
  • ✓ Factory-direct pricing for your H / HNL High Pushout Self-Clinching Nuts
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.