DIN 1443 Clevis Pins without Head

DIN 1443 clevis pins without head (ISO 2340), shank d 4–90 mm — the headless clevis pin retained between two ears with a cotter through the cross-hole, with the collected h11 shank / H13 hole / chamfer / w ladder per size.

Last updated: 2026-11

Request a Quote

DIN 1443 Clevis Pins without Head in an industrial setting
Illustrative image redrawn from real DIN 1443 Clevis Pins without Head product references — not a photograph of stocked items.

Specifications

A DIN 1443 pin is the clevis pin with the head left off: a parallel h11 shank with a cross-hole for the cotter near the point, retained by the joint geometry itself — it sits in a clevis and is held by a cotter pin passing through both ears and the pin. The collected ladder runs 24 shank sizes, d = 4 to 90 mm, and carries per size: the cotter hole diameter d1 (H13), from 1 mm at the 4 mm pin to 13 mm at the 90 mm pin; the end chamfer c (max); and w, the distance from the pin end to the hole centre (2,2 mm at the small end growing to 16 mm at the large). The reading order at assembly mirrors the headed clevis pin (this catalog's ISO 2341 page): fit the h11 shank to the clevis bores as a running fit, use w to check the cotter hole clears the outer ear's edge once the pin is through the stack, and drive the retainment through d1 — the hole pairs with a metric split cotter pin from the ISO 1234 ladder (see the DIN 94 / ISO 1234 page for sizes and pairing). Because the pin has no head, the joint itself must locate it axially — a retained-between-ears stack or a washer behind the cotter ear; the headed series is the right choice where a single-sided face must take the load. Materials, finishes and shear ratings are not tabulated by the collected specification — per RFQ.

Standard DIN 1443 — clevis pins without head; ISO 2340 is the internationally maintained successor designation (source index lists "DIN 1443; ISO 2340")
Size range Shank d 4 – 90 mm, twenty-four sizes in the collected ladder (4–24 in 2 mm steps, then 27–90)
Shank tolerance h11 on the shank diameter — running fit into the clevis bores; drill or ream to nominal, not to a measured pin
Cotter hole d1 (H13): 1 at the 4 mm pin → 13 at the 90 mm pin; pairs with metric split cotter pins per the ISO 1234 ladder
Hole position End chamfer c (max) 1–6 mm; w (end to hole centre) 2,2 → 16 mm — the dimension that must clear the outer ear at assembly
Materials / finishes / ratings Not tabulated by the collected specification — per RFQ (state material, shear load and environment at quotation)
DIN 1443 clevis pins without head — hole, chamfer and eye width, shank d 4–90 mmAll dimensions in millimetres, comma decimal separators preserved from the source. The source serves the ladder in two blocks (d 4–24, then 27–90); the blocks are stitched into one row-per-size ladder here. d (h11) = shank diameter with tolerance class; d1 (H13) = cotter hole diameter; c = end chamfer (max); w = distance from end to hole centre (min). Length ladder is not tabulated by the source — per RFQ.
Shank Dia. (d h11)Cotter Hole Dia. (d1 H13)End Chamfer (c max.)End to Hole Centre (w)
4112,2
51,222,9
61,623,2
8223,5
103,224,5
123,2335,5
14436
16436
18537
20548
22548
246,349
276,349
308410
338410
368410
408410
4510412
5010412
5510414
6010614
7013616
8013616
9013616
  • Row 6 (12): The source prints the end chamfer at d = 12 as "33" where the surrounding ladder steps 1, 2, 2, 2, 2, …, 3 indicate a decimal-comma value (3,3); reproduced verbatim as printed. Verify against the standard before quoting this cell.

Materials

  • Material and finish specified per RFQ — clevis pins take single-shear pivot loads and frequent reassembly; state the working load, clevis width and environment with the order

Ordering & documentation

Documents

Shipments of DIN 1443 Clevis Pins without Head are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 1443 Clevis Pins without Head orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 1443 Clevis Pins without Head), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for din 1443 clevis pins without head are confirmed at quotation — send pin type, diameter, length and material on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

DIN 1443 Clevis Pins without Head are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 1443 clevis pins without head dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

When is a headless DIN 1443 clevis pin the right choice over the headed ISO 2341 pin?

The head on a clevis pin is a single-sided axial stop — it takes the thrust and locates the pin from one face, which is what the headed ISO 2341 / DIN EN 22341 series (this catalog's iso-2341-clevis-pins-metric page) is for. The headless DIN 1443 / ISO 2340 pin is the choice when the geometry has no face to put a head against: the pin passes through both ears (or through a stack capped by a washer on the far side) and the cotter through the cross-hole does the retaining. Sizing order off the collected table: match the h11 shank to the clevis bores as a running fit; check w — 2,2 mm at the 4 mm pin growing to 16 mm at the 90 mm pin — against the stack so the cotter hole lands fully outside the outer ear, not buried in it; and pick the cotter off the d1 column (1 mm hole at the 4 mm pin, 13 mm at the 90 mm pin) using the ISO 1234 pairing on this catalog's DIN 94 page. Two cautions from the collected data: the ladder covers 24 sizes and jumps from 24 to 27 mm — intermediate steps are not covered by published tables, quote them explicitly; and one published cell (end chamfer at d 12, printed "33") carries a transcription quirk flagged under the table — verify against the standard before quoting that cell. Materials, finishes and shear ratings are RFQ lines.

Which documents can I request with an order of DIN 1443 Clevis Pins without Head?

Orders can be documented with a mill test certificate (MTC), a dimensional report and a salt spray test report, with full batch traceability from raw material to finished product; availability of each document for this designation is confirmed at quotation.

What should an RFQ for DIN 1443 Clevis Pins without Head state?

State the full designation (DIN 1443), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 1443 Clevis Pins without Head inquiry

  • ✓ Identify the pin type and its standard (for example parallel dowel or slotted spring pin).
  • ✓ Give nominal diameter, length and required fit/tolerance; include the mating-hole size and whether it is drilled or reamed.
  • ✓ State material, heat-treatment condition and corrosion finish, plus any specified shear or retention duty.
  • ✓ Give quantity per size, destination and inspection/certificate requirements.
  • ✓ Factory-direct pricing for your DIN 1443 Clevis Pins without Head
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.