ISO 8745 Parallel Grooved Pins

ISO 8745 parallel grooved pins, d1 1,5 to 25 over a 32-length ladder (l 8 to 200) — the separate parallel-grooved designation, with two verbatim source quirks flagged (non-monotone shear row, duplicated 16-column groove cells).

Last updated: 2026-11

Request a Quote

ISO 8745 Parallel Grooved Pins in an industrial setting
Illustrative image redrawn from real ISO 8745 Parallel Grooved Pins product references — not a photograph of stocked items.

Specifications

ISO 8745 is the second parallel-grooved designation in this catalog alongside ISO 8740/8741 — same working principle (three parallel grooves, displacement grip, no reaming), a separate standard with its own collected table, and orderable only by the designation your drawing names. The table runs d1 1,5 → 25 (tolerance h9 at 1,5, h11 from 10) with chamfer a 0,2 → 3 and the double-shear row over a 32-length groove-diameter ladder, l 8 → 200, groove diameters 1,63 → 25,6 banded +0,05 / ±0,05 / ±0,1. Two source quirks are carried verbatim with anomaly flags rather than normalized: the double-shear row prints 444 | 283 | 444 across d1 12 / 16 / 20, and from l 32 through l 50 the d1 20 column repeats the d1 16 groove value 16,55 while d1 25 prints 25,5 against the surrounding 25,6 — both marked on the table, both confirmed-per-RFQ items if your build lands there. Taper-free full-length grip, material and finish are not tabulated — per RFQ.

Standard ISO 8745 — parallel grooved pins
Size range d1 1,5 – 25 in the collected rows; tolerance h9 (1,5) / h11 (from 10) per the source banding
Chamfer a: 0,2 → 3
Double shear 4,4 → 444 kN; non-monotone 444 | 283 | 444 at d1 12 / 16 / 20 per the source — confirm large sizes per RFQ
Length ladder l 8 – 200 (32 lengths) with groove diameter per length, 1,63 → 25,6
Source quirks l 32 – 50: d1 20 column repeats the d1 16 value (16,55) and d1 25 prints 25,5 vs the 25,6 run — verbatim, confirm per RFQ
Not tabulated Material, hardness, finish — per RFQ
Designation note ISO 8740/8741 are the sibling parallel-grooved designations in this catalog — order by drawing designation
ISO 8745 parallel grooved - attribute rowsAll dimensions in millimetres. Column header is the source's d1 nominal series; attribute labels carried verbatim: 'tolerance' is the d1 tolerance band per diameter (h9 at d1 1,5, h11 from d1 10 up, per the source's tolerance row), a = chamfer, and 'The smallest cutting force two sections kN' is the source's rendering of the minimum double-shear (two-section) load. The force row is non-monotone at the top per the source and carried verbatim (flagged).
Row label1,522,5345681012162025
d1 Nominal1,522,5345681012162025
toleranceh9h11
a =0,20,250,30,40,50,630,811,21,622,53
The smallest cutting force two sections kN4,46,411,317,625,445,270,4101,8181283444283444
  • Row 4 (The smallest cutting force two sections kN): the force row is non-monotone at the top per the source: it prints 444 | 283 | 444 across d1 12 / 16 / 20 instead of a continuing ladder. Carried verbatim, not normalized - confirm the large-diameter double-shear values per RFQ.
ISO 8745 parallel grooved - groove diameter ladder, lengths 8 - 200Groove diameter per pin length, in millimetres. The source's tolerance band row ('+0,05', '±0,05', '±0,1') applies across the d1 columns as printed: +0,05 for the smallest, ±0,05 for the mid series, ±0,1 from d1 12 up. Blank = length not tabulated for that d1.
l Nominall min.l max.d1 1,5d1 2d1 2,5d1 3d1 4d1 5d1 6d1 8d1 10d1 12d1 16d1 20d1 25
87,758,251,632,152,653,2
109,7510,251,632,152,653,24,255,256,25
1211,512,51,632,152,73,254,255,256,25
1413,514,51,632,152,73,254,35,36,258,2510,3
1615,516,51,632,152,73,254,35,36,258,2510,3
1817,518,51,632,152,73,34,35,36,38,310,312,3
2019,520,51,632,152,73,34,35,36,38,310,312,3
2221,522,52,152,73,34,355,356,38,3510,3512,35
2423,524,52,152,73,34,355,356,38,3510,3512,35
2625,526,52,152,73,34,355,356,358,3510,412,416,520,5525,5
2827,528,52,152,73,34,355,356,358,3510,412,416,520,5525,5
3029,530,52,152,73,34,355,356,358,3510,412,416,520,5525,5
3231,532,53,254,355,356,358,3510,412,416,5516,5525,5
3534,535,53,254,355,356,358,3510,412,416,5516,5525,5
4039,540,53,254,355,356,358,3510,412,416,5516,5525,5
4544,545,54,35,356,358,410,412,416,5516,5525,5
5049,550,54,35,356,358,410,4512,4516,5516,5525,5
5554,2555,754,35,36,358,410,4512,4516,5520,625,6
6059,2560,754,35,36,358,410,4512,4516,620,625,6
6564,2565,756,38,410,4512,4516,620,625,6
7069,2570,756,38,410,4512,4516,620,625,6
7574,2575,756,38,410,4512,4516,620,625,6
8079,2580,756,38,3510,4512,4516,620,625,6
8584,2585,758,3510,412,416,620,625,6
9089,2590,758,3510,412,416,620,625,6
9594,2595,758,3510,412,416,620,625,6
10099,25100,758,3510,412,416,620,625,6
120119,25120,7510,412,416,5520,625,6
140139,25140,7510,3512,3516,5520,625,6
160159,25160,7510,3512,3516,5520,625,6
180179,25180,7510,3512,3516,5520,625,6
200199,25200,7510,3512,3516,5520,625,6
  • Row 25 (90): from l 32 through l 50 (rows 24-28) the source prints 16,55 in BOTH the d1 16 and d1 20 columns - the 20-column cells duplicate the 16-column value - and d1 25 prints 25,5 where the surrounding ladder runs 25,6. Carried verbatim, not normalized.

Materials

  • Material and finish specified per RFQ — parallel grooved pins commonly run spring or hardened steel; stainless available for corrosive cells at reduced groove-forming headroom. State host material and whether the joint is fatigue-loaded at quotation — the displacement grip behaves differently under cyclic load than an elastic pin

Ordering & documentation

Documents

Shipments of ISO 8745 Parallel Grooved Pins are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 8745 Parallel Grooved Pins orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ISO 8745 Parallel Grooved Pins), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for iso 8745 parallel grooved pins are confirmed at quotation — send pin type, diameter, length and material on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

ISO 8745 Parallel Grooved Pins are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 8745 parallel grooved pins dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Two cells on this page look wrong (the 16,55 repeated at d1 20, and 25,5 against 25,6). Should I trust the table?

Treat those specific cells as print-as-found, not as design values. The collected page, from l 32 to l 50, prints 16,55 in both the d1 16 and the d1 20 columns — the 20-column cells duplicate the neighbouring value — and the d1 25 column prints 25,5 where the lengths above and below run 25,6. This batch carries source tables token-for-token and marks anomalies rather than guessing a correction, so the flags sit on those rows in the table above. What you can rely on: the rest of the ladder steps cleanly (1,63 at the bottom through 25,6 across the mid and upper lengths), the tolerance bands are consistent (+0,05/0, ±0,05, ±0,1), and every other attribute row is monotone. What you should confirm per RFQ: any build landing in l 32 – 50 at d1 20 or d1 25 — quote the groove diameter from the confirmed value, not from the flagged cells. The same rule covers the double-shear row's 444 | 283 | 444 repeat at d1 12 / 16 / 20.

Which documents can I request with an order of ISO 8745 Parallel Grooved Pins?

Orders can be documented with a mill test certificate (MTC), a dimensional report and a salt spray test report, with full batch traceability from raw material to finished product; availability of each document for this designation is confirmed at quotation.

What should an RFQ for ISO 8745 Parallel Grooved Pins state?

State the full designation (ISO 8745), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ISO 8745 Parallel Grooved Pins inquiry

  • ✓ Identify the pin type and its standard (for example parallel dowel or slotted spring pin).
  • ✓ Give nominal diameter, length and required fit/tolerance; include the mating-hole size and whether it is drilled or reamed.
  • ✓ State material, heat-treatment condition and corrosion finish, plus any specified shear or retention duty.
  • ✓ Give quantity per size, destination and inspection/certificate requirements.
  • ✓ Factory-direct pricing for your ISO 8745 Parallel Grooved Pins
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.