DIN 258 Taper Pins with External Thread

DIN 258 taper pins with external thread, nominal d 5–20 mm — the driven taper pin that carries a machined shoulder, a male stud thread (M5–M16) and a minimum grip length L2, for assemblies the pin must be nutted out of rather than drifted.

Last updated: 2026-11

Request a Quote

DIN 258 Taper Pins with External Thread in an industrial setting
Illustrative image redrawn from real DIN 258 Taper Pins with External Thread product references — not a photograph of stocked items.

Specifications

A DIN 258 pin is a taper pin whose large end is machined down to a shoulder and cut with a male thread, so instead of being drifted out like a plain DIN 1 taper pin it can be released with a nut. The collected table runs the nominal taper series d = 5 to 20 mm; per size it carries the shoulder diameter d2 (5,5 mm at d 5 rising to 21,7 mm at d 20), the stud thread d3 (M 5 through M 12, then M 16 for both d 16 and d 20), the thread length b (14–35 mm), and L2 — the minimum distance from the threaded end to the point where the taper measures nominal, 25 mm at the 5 mm pin growing to 85 mm at the 20 mm pin. Reading order at assembly: size the taper seat from d exactly as for a plain taper pin (ream to a matched taper gauge, fit by hand-tight depth), let d2 clear the boss face so the nut seats on the shoulder not on the taper, and check that L2 leaves the measured taper inside the clamped parts rather than inside the thread runout. Where the drawing calls the same function with an internal thread — the pin pulled with a bolt instead of nutted — that is the DIN 7978 page on this catalog. Materials, finishes and shear ratings are not tabulated by the collected specification — per RFQ.

Standard DIN 258 — taper pins with external thread (male stud end with shoulder for nut release)
Size range Nominal taper d 5 – 20 mm, seven sizes in the collected ladder (5, 6, 8, 10, 12, 16, 20)
Shoulder d2: 5,5 at d 5 → 21,7 at d 20 mm — machined shoulder the release nut seats against
Stud thread d3: M 5 / M 6 / M 8 / M 10 / M 12 / M 16 / M 16 (M 16 repeated at d 16 and d 20 per the source ladder); thread length b: 14 → 35 mm
Grip reference L2 (threaded end to nominal-taper measuring point): 25 / 30 / 40 / 45 / 55 / 72 / 85 mm across the ladder
Materials / finishes / ratings Not tabulated by the collected specification — per RFQ (state material, joint load and environment at quotation)
DIN 258 taper pins with external thread — shoulder, thread and thread-length series, nominal d 5–20 mmAll dimensions in millimetres, comma decimal separators preserved from the source. The source serves the table transposed (parameters as rows, nominal diameters as columns); the ladder below is transposed back to one row per size. d2 = shoulder diameter; d3 = thread designation; b = thread length; L2 = minimum distance from the large (threaded) end to the measured taper diameter. Taper rate and overall length ladder beyond L2 are not tabulated by the source — per RFQ.
Nominal dShoulder Dia. (d2)Thread (d3)Thread Length (b)L2
55,5M 51425
66,6M 61830
88,8M 82240
1010,9M 102445
1213,1M 122755
1617,4M 163572
2021,7M 163585

Materials

  • Material and finish specified per RFQ — state the shear load, the clamped stack and the environment; tapered fits are size-critical and confirmed at quotation

Ordering & documentation

Documents

Shipments of DIN 258 Taper Pins with External Thread are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 258 Taper Pins with External Thread orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 258 Taper Pins with External Thread), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for din 258 taper pins with external thread are confirmed at quotation — send pin type, diameter, length and material on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

DIN 258 Taper Pins with External Thread are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 258 taper pins with external thread dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

How is a DIN 258 pin different from a plain taper pin or a DIN 7978 pin?

All three seat on the same nominal taper ladder — d 5, 6, 8, 10, 12, 16, 20 in this table — so the reamed seat and the fit-checking procedure are the same. The difference is the release mechanism at the large end. A plain DIN 1 / ISO 2339 taper pin is driven out with a drift; a DIN 258 pin is machined to a shoulder d2 and a male thread (M 5–M 16), so it is released by running a nut back off the stud — useful where a drift blow would damage the assembly or where the pin sits in a position a drift cannot reach. A DIN 7978 pin does the same job from the opposite side: its large end carries an internal thread and the pin is extracted by screwing a bolt in. Two readings off the collected DIN 258 table matter at assembly: L2 (25 mm at d 5 rising to 85 mm at d 20) is the distance from the threaded end to the point the taper measures nominal — it must land inside the clamped parts, so check it against the stack before final-sizing the bore; and the d3 ladder repeats M 16 at both d 16 and d 20, so the 20 mm pin does not step the thread up — the shoulder diameter d2 does the sizing there. Load ratings, materials and finishes are not in the collected table — quote them at RFQ.

Which documents can I request with an order of DIN 258 Taper Pins with External Thread?

Orders can be documented with a mill test certificate (MTC), a dimensional report and a salt spray test report, with full batch traceability from raw material to finished product; availability of each document for this designation is confirmed at quotation.

What should an RFQ for DIN 258 Taper Pins with External Thread state?

State the full designation (DIN 258), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 258 Taper Pins with External Thread inquiry

  • ✓ Identify the pin type and its standard (for example parallel dowel or slotted spring pin).
  • ✓ Give nominal diameter, length and required fit/tolerance; include the mating-hole size and whether it is drilled or reamed.
  • ✓ State material, heat-treatment condition and corrosion finish, plus any specified shear or retention duty.
  • ✓ Give quantity per size, destination and inspection/certificate requirements.
  • ✓ Factory-direct pricing for your DIN 258 Taper Pins with External Thread
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.