DIN 674 Flat Round Head Rivets
DIN 674 flat round head solid rivets, nominal d1 1,4–6 mm — the small-series dome-head solid rivet for sheet and light fabrication, with the collected head diameter and head geometry ladder.
Last updated: 2026-11
Specifications
DIN 674 is the small-series solid rivet with a flat round (dome) head: a plain solid shank driven cold or hot so the tail spreads into a second head, closing sheet, leather, light brackets and hobby-scale fabrication where a blind hole is not needed and both sides are reachable. The collected table runs nominal d1 = 1,4 to 6 mm — well below the hot-rivet structural series — and carries per size the head diameter d2 (3,2 mm at the 1,4 mm rivet stepping up to 13,5 mm at the 6 mm), so the head is roughly 2,2–2,5× the shank, plus the head dimensions e and k as lettered by the source. Sizing at the bench: drill the hole a touch over the shank (the shank must pass freely — solid rivets close by bulging into the hole), cut the tail to about one shank-diameter of projection, and set the head against solid backing. Where only one side is reachable, the blind rivet pages in this family take over; where the head must sit flush, the countersunk DIN 661 series is the counterpart. Materials (aluminium, brass, mild steel and copper all appear in the trade at this size range) and the length ladder are not tabulated by the collected specification — per RFQ.
| Standard | DIN 674 — flat round head rivets (solid shank, two-side access required) |
|---|---|
| Size range | Nominal d1 1,4 – 6 mm, nine sizes in the collected ladder (1,4 / 1,6 / 2 / 2,5 / 3 / (3,5) / 4 / 5 / 6) |
| Head diameter | d2: 3,2 → 13,5 mm across the ladder (≈2,2–2,5× the shank at every size) |
| Head geometry | e: 0,7 → 3 mm; k: 0,7 → 3 mm as lettered by the source |
| Materials / length ladder | Not tabulated by the collected specification — per RFQ (state material, length and setting method at quotation) |
| Nominal d (d1) | Head Dia. (d2) | e | Head Height (k) |
|---|---|---|---|
| 1,4 | 3,2 | 0,7 | 0,7 |
| 1,6 | 3,6 | 0,8 | 0,8 |
| 2 | 4,5 | 1 | 1 |
| 2,5 | 5,6 | 1,25 | 1,3 |
| 3 | 6,8 | 1,5 | 1,5 |
| (3,5) | 7,8 | 1,75 | 1,8 |
| 4 | 9 | 2 | 2 |
| 5 | 11,2 | 2,5 | 2,5 |
| 6 | 13,5 | 3 | 3 |
- Row 6 ((3,5)): Nominal 3,5 mm is printed in parentheses in the source — the conventional marker for a non-preferred size. Reproduced verbatim; confirm availability before quoting.
Materials
- Material specified per RFQ — small-series solid rivets are supplied in aluminium, brass, steel and copper by application; state the joined materials and whether the joint will see moisture with the order
Ordering & documentation
Documents
Shipments of DIN 674 Flat Round Head Rivets are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 674 Flat Round Head Rivets orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 674 Flat Round Head Rivets), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for din 674 flat round head rivets is 10,000–50,000 pieces depending on size (applies to the standard sizes and finishes for din 674 flat round head rivets; mixed, special or custom variants are quoted — final commercial terms per quotation) Standard production for din 674 flat round head rivets run 10–20 days. Quantities or variants of din 674 flat round head rivets outside the standard range are confirmed at quotation.
Storage & shipping
DIN 674 Flat Round Head Rivets are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 674 flat round head rivets dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
When does a DIN 674 solid rivet beat a blind rivet, and what does the table decide?
A solid rivet wins when both sides of the joint are reachable and the joint wants the cheapest, most vibration-proof permanent fastener with no mandrel void down the middle — a blind rivet always leaves the mandrel stub and a hollow body. What the collected table decides is the head print: it gives the head diameter d2 for every shank from 1,4 to 6 mm (3,2 → 13,5 mm), which is the number your bucking bar and head-clearance check need, plus the head dimensions e and k as printed. What it does not give: the length ladder and the material — pick length as shank grip plus roughly one shank diameter of tail to close, and state material (aluminium closes cold; steel may want heat at the upper sizes) on the RFQ. Two cautions from the capture: the 3,5 mm size is printed in parentheses — the non-preferred marker — so confirm stock before drawing it in, and the source letters e and k without a legend, so verify against the standard before quoting those cells in a drawing.
What is the MOQ and lead time for DIN 674 Flat Round Head Rivets?
Orders under this designation have a minimum order quantity of 10,000–50,000 pieces depending on size. Standard production ships in 10–20 days. Final commercial terms are confirmed per quotation.
What should an RFQ for DIN 674 Flat Round Head Rivets state?
State the full designation (DIN 674), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 674 Flat Round Head Rivets inquiry
- ✓ Identify blind, solid or structural rivet type and the applicable product standard.
- ✓ Give rivet-body diameter and grip range for the complete material stack, plus the prepared-hole size.
- ✓ Specify head style/clearance and state body and mandrel materials separately for blind rivets.
- ✓ For load-bearing joints, provide required rivet-specific tensile and shear values; do not substitute a bolt property class.
- ✓ State finish, quantity, destination and any lot-test or traceability documents required.
- ✓ Factory-direct pricing for your DIN 674 Flat Round Head Rivets
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support