Solid Rivet Head Dimensions by Head Type
Cold-driven solid rivet head geometry per head type across two shank ladders — snap, universal, 60° countersunk/raised countersunk, 90° countersunk and flat heads, shank 1 - 39 mm with diameter tolerances — the head-type comparison behind riveted-joint design and legacy structural work.
Last updated: 2026-11
Specifications
Solid rivets are specified by their head as much as their shank: the head decides the joint's profile, bearing and drive behavior. This collected page tabulates the head geometry per head type in two shank ladders. The large ladder (shank 14 - 39 mm) compares 60° countersunk & raised countersunk (nominal dia D and raised height W: shank 20 → D 30 / W 4,0), snap head (D and depth K: shank 20 → D 32 / K 13) and universal head (D and K, plus the R and r radii ladder: shank 20 → R 60 / r 12,0) — with per-size shank diameter tolerances (+/- 0,43 at 14-18 rising to +/- 0,62 at 27-39, decimal commas as printed). The small ladder (shank 1 - 16 mm) adds the 90° countersunk and flat head columns to the same head set, tolerances from +/- 0,07 at the 1-1,6 mm shanks to +/- 0,14 at 12-16 (shank 3: 90° csk D 6, snap D 5,3 / K 1,8, universal D 6 / K 1,2, R 9,0 / r 1,8, flat D 6 / K 0,9). Carried verbatim with flags: the large ladder prints the nominal "24" twice (with different head dims — customarily the second would be 26, but the source prints 24; flagged, not corrected), the small ladder mixes decimal comma and point once ("12.3" at shank 7), and the flat head column stops at shank 10 with blank cells above. The existing per-head solid-rivet pages (DIN 660/661/674 series in this family) carry the standard-specific ladders; this page is the head-type comparison across the family. Materials, shear strengths and length ladders are not tabulated — per RFQ.
| Large ladder | Shank 14 - 39 mm: 60° csk & raised csk (D, W), snap head (D, K), universal head (D, K, R, r); tol +/- 0,43 - +/- 0,62 |
|---|---|
| Small ladder | Shank 1 - 16 mm: 90° csk, snap, universal, flat head (D, K per head) + universal R/r; tol +/- 0,07 - +/- 0,14 |
| Example, shank 20 | 60° csk D 30 / W 4,0; snap D 32 / K 13; universal D 40 / K 8,0 / R 60 / r 12,0 |
| Example, shank 3 | 90° csk D 6; snap D 5,3 / K 1,8; universal D 6 / K 1,2 / R 9,0 / r 1,8; flat D 6 / K 0,9 |
| Notation | mm, decimal commas (one decimal-point cell flagged); blank cells = not tabulated by the source |
| Not tabulated | Materials, shear/tear strengths, length ladders, hole preparation — per RFQ (state joint stack and load at quotation) |
| Nom Shank dia | Dia Tol | 60 Deg Csk & Raised Csk | Snap Hd | Universal Hd | |||||
|---|---|---|---|---|---|---|---|---|---|
| Nom dia | Raise Ht | Nom dia | Nom Depth | Nom dia | Nom Depth | Rad | Rad | ||
| D | W | D | K | D | K | R | r | ||
| 14 | +/- 0,43 | 21 | 2,8 | 22 | 9 | 28 | 5,6 | 42 | 8,4 |
| 16 | +/- 0,43 | 24 | 3,2 | 25 | 10 | 32 | 6,4 | 48 | 9,6 |
| 18 | +/- 0,43 | 27 | 3,6 | 28 | 11,5 | 36 | 7,2 | 54 | 11,0 |
| 20 | +/- 0,52 | 30 | 4,0 | 32 | 13 | 40 | 8,0 | 60 | 12,0 |
| 24 | +/- 0,52 | 33 | 4,4 | 36 | 14 | 44 | 8,8 | 66 | 13,0 |
| 24 | +/- 0,52 | 36 | 4,8 | 40 | 16 | 48 | 9,6 | 72 | 14,0 |
| 27 | +/- 0,62 | 40 | 5,4 | 43 | 17 | 54 | 10,8 | 81 | 16,0 |
| 30 | +/- 0,62 | 45 | 6,0 | 48 | 19 | 60 | 12,0 | 90 | 18,0 |
| 33 | +/- 0,62 | 50 | 6,6 | 53 | 21 | 66 | 13,2 | 99 | 20 |
| 36 | +/- 0,62 | 55 | 7,2 | 58 | 23 | 72 | 14,4 | 108 | 22 |
| 39 | +/- 0,62 | 59 | 7,8 | 62 | 25 | 78 | 15,6 | 117 | 23 |
- Row 5 (18): nominal shank dia prints "24" twice (rows 24 and 24 with different head dims — the second is customarily 26, but the source prints 24) — carried verbatim, flagged not corrected
| Nominal Shank dia | Dia Tol | 90 Deg Csk | Snap Hd | Universal Hd | Flat Head | |||||
|---|---|---|---|---|---|---|---|---|---|---|
| Nom dia | Nom dia | Nom Depth | Nom dia | Nom Depth | Rad | Rad | Nom dia | Nom Depth | ||
| D | D | K | D | K | R | r | D | K | ||
| 1 | +/- 0,07 | 2 | 1,8 | 0,6 | 2 | 0,4 | 3,0 | 0,6 | 2 | 0,25 |
| 1,2 | +/- 0,07 | 2,4 | 2,1 | 0,7 | 2,4 | 0,5 | 3,6 | 0,7 | 2,4 | 0,3 |
| 1,6 | +/- 0,07 | 3,2 | 2,8 | 1,0 | 3,2 | 0,6 | 4,8 | 1,0 | 3,2 | 0,4 |
| 2,0 | +/- 0,07 | 4 | 3,5 | 1,2 | 4 | 0,8 | 6,0 | 1,2 | 4 | 0,6 |
| 2,5 | +/- 0,07 | 5 | 4,4 | 1,5 | 5 | 1 | 7,5 | 1,5 | 5 | 0,8 |
| 3 | +/- 0,07 | 6 | 5,3 | 1,8 | 6 | 1,2 | 9,0 | 1,8 | 6 | 0,9 |
| 3,5 | +/- 0,09 | 7 | 6,1 | 2,1 | 7 | 1,4 | 10,5 | 2,1 | 7 | 1,0 |
| 4 | +/- 0,09 | 8 | 7 | 2,4 | 8 | 1,6 | 12 | 2,4 | 8 | 1,3 |
| 5 | +/- 0,09 | 10 | 8,8 | 3,0 | 10 | 2,0 | 15 | 3,0 | 9 | 1,5 |
| 6 | +/- 0,09 | 12 | 10,5 | 3,6 | 12 | 2,4 | 18 | 3,6 | 10 | 1,8 |
| 7 | +/- 0,11 | 14 | 12.3 | 4,2 | 14 | 2,8 | 21 | 4,2 | 14 | 2,0 |
| 8 | +/- 0,11 | 16 | 14 | 4,8 | 16 | 3,2 | 24 | 4,8 | 16 | 2,5 |
| 10 | +/- 0,11 | 20 | 18 | 6,0 | 20 | 4,0 | 30 | 6,0 | 20 | |
| 12 | +/- 0,14 | 24 | 21 | 7,2 | 24 | 4,8 | 36 | 7,2 | ||
| 14 | +/- 0,14 | 25 | 8,4 | 28 | 5,6 | 42 | 8,4 | |||
| 16 | +/- 0,14 | 28 | 9,6 | 32 | 6,4 | 48 | 9,6 |
- Row 12 (6): snap head dia prints "12.3" with a decimal point amid the decimal-comma convention — as printed
- Row 14 (8): flat head D prints "20" with K blank at shank 10; flat head columns blank from shank 12 up — values not tabulated by the source, carried verbatim
Materials
- Solid rivet material follows the joint: soft rivet steel for structural work, aluminium alloys where weight or corrosion leads, brass and copper for electrical and heritage work — driven cold in the small sizes and hot in the large. RFQ with shank size, head type, material and joint stack; where the head sits in a flow or aerodynamic surface, name the countersink angle from this table explicitly
Ordering & documentation
Documents
Shipments of Solid Rivet Head Dimensions by Head Type are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Solid Rivet Head Dimensions by Head Type orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (Solid Rivet Head Dimensions by Head Type), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for solid rivet head dimensions by head type is 10,000–50,000 pieces depending on size (applies to the standard sizes and finishes for solid rivet head dimensions by head type; mixed, special or custom variants are quoted — final commercial terms per quotation) Standard production for solid rivet head dimensions by head type run 10–20 days. Quantities or variants of solid rivet head dimensions by head type outside the standard range are confirmed at quotation.
Storage & shipping
Solid Rivet Head Dimensions by Head Type are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store solid rivet head dimensions by head type dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
How do I choose between the head types on this table for a riveted joint?
The table is the geometry, the joint picks the head. Snap (round) head is the default for strength and hand-setting — largest depth K, so the biggest head-to-shank bearing and the most metal to close. Countersunk heads (60° and 90° on this ladder) buy a flush surface at the cost of head depth: the countersink eats into the sheet thickness, so they want thicker plates or a lower-clamp application — the raised-countersunk column (W) is the compromise when flush is needed but the sheet is thin. Universal head is the aerospace-heritage profile — a flattened round with radiused edges (the R/r columns) that sits between snap and countersunk in protrusion and carries the fatigue-friendly blend radii. Flat head is the thin-sheet option, which is why its ladder stops at shank 10 on the collected page. Practical check before ordering: verify the sheet stack supports the head depth K plus the countersink angle you pick — the columns are tabulated per size here precisely so that check happens off the table, not off the shelf.
What is the MOQ and lead time for Solid Rivet Head Dimensions by Head Type?
Orders under this designation have a minimum order quantity of 10,000–50,000 pieces depending on size. Standard production ships in 10–20 days. Final commercial terms are confirmed per quotation.
What should an RFQ for Solid Rivet Head Dimensions by Head Type state?
State the full designation (Solid Rivet Head Dimensions by Head Type), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Solid Rivet Head Dimensions by Head Type inquiry
- ✓ Identify blind, solid or structural rivet type and the applicable product standard.
- ✓ Give rivet-body diameter and grip range for the complete material stack, plus the prepared-hole size.
- ✓ Specify head style/clearance and state body and mandrel materials separately for blind rivets.
- ✓ For load-bearing joints, provide required rivet-specific tensile and shear values; do not substitute a bolt property class.
- ✓ State finish, quantity, destination and any lot-test or traceability documents required.
- ✓ Factory-direct pricing for your Solid Rivet Head Dimensions by Head Type
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support