DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel)

DIN EN ISO 16583-2003 open end blind rivets with break pull mandrel and countersunk head, Cu/St or Cu/Br or Cu/SSt: shank and head diameters, head height, mandrel diameter, grip, hole sizes, and the shear/tensile/mandrel/head-retention load rows per size.

Last updated: 2026-11

Request a Quote

DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel) in an industrial setting
Illustrative image redrawn from real DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel) product references — not a photograph of stocked items.

Specifications

ISO 16583 countersunk open-end blind rivets are the flush-finish break-mandrel rivet in the copper combinations — Cu/steel, Cu/brass, Cu/stainless — where the rivet must sit below the surface and the copper body brings corrosion compatibility or electrical conductivity. The collected table carries four sizes (read vertically by the d max/min rows: 3.08/2.85, 3.28/3.05, 4.08/3.85, 4.88/4.65) with head diameter dk max/min (6.3/5.4 to 10.1/8.3), countersunk head height k max (1.3 to 2), mandrel d1 max (2 to 2.95), minimum grip L1 (25, 25, 25, 27), mandrel protrusion b (L(max)+3.5 to L(max)+4.5 as printed), recommended hole sizes (3.1/3.2 up to 4.9/5.0 min/max), and the load rows: minimum shear 760/800/1500/2000 N, minimum tensile 950/1000/1800/2500 N, maximum mandrel break load 3000/3000/4500/5000 N, and head retention test load 15/15/20/25 N. The load rows are what separate this ladder from a geometry-only rivet table — they are the acceptance numbers behind the riveted joint.

Standard / scope DIN EN ISO 16583-2003 open end blind rivets, break pull mandrel, countersunk head — Cu/St or Cu/Br or Cu/SSt, four sizes as tabulated
Shank d max/min 3.08/2.85, 3.28/3.05, 4.08/3.85, 4.88/4.65 — the size identification, read vertically
Head dk / height k / mandrel d1 dk max/min 6.3/5.4, 6.7/5.8, 8.4/6.9, 10.1/8.3; k max 1.3/1.3/1.7/2; d1 max 2/2/2.45/2.95
Grip L1 / mandrel b / hole L1 min 25, 25, 25, 27; b max L(max)+3.5 to L(max)+4.5 as printed; recommended hole min/max 3.1/3.2, 3.3/3.4, 4.1/4.2, 4.9/5.0
Load rows Min shear 760/800/1500/2000 N; min tensile 950/1000/1800/2500 N; max mandrel break 3000/3000/4500/5000 N; head retention test 15/15/20/25 N
Not tabulated Length (grip) ladder beyond L1 min, edge distances, fatigue — per RFQ
DIN EN ISO 16583-2003 open end blind rivets, break pull mandrel, countersunk head, Cu/St or Cu/Br or Cu/SSt — by size (table 1 of 1)mm. The four size columns carry no printed size designations (d 3.2/4/4.8/6.4-class rivets by the d rows). Attribute-label table positionally paired with the numeric grid; values untouched.
AttributeSub-labelNote
dmax3.083.284.084.88
d2.853.053.854.65
d kmax6.36.78.410.1
d k5.45.86.98.3
kmax1.31.31.72
d 1max222.452.95
L 1min25252527
bmaxL(max)+3.5L(max)+4L(max)+4L(max)+4.5
Recommend Hole Sizemin3.13.34.14.9
Recommend Hole Size3.23.44.25
Minimum shear load(N)Minimum shear load(N)Minimum shear load(N)76080015002000
Minimum tensile load(N)Minimum tensile load(N)Minimum tensile load(N)950100018002500
Maximum mandrel break load(N)Maximum mandrel break load(N)Maximum mandrel break load(N)3000300045005000
Head retention test load(N)Head retention test load(N)Head retention test load(N)15152025
  • The four size columns are unlabeled on the collected page — rivet sizes are carried by the d (mandrel/shank) max/min rows, read vertically.
  • The site printed the b max row ('L(max)+3.5 / L(max)+4 / L(max)+4 / L(max)+4.5') twice — once as a styled header-class row (salvaged in the corpus, duplicate) and once inside the grid; this rendering keeps the grid copy only.

Materials

  • The Cu body is chosen for the joint, not the looks: Cu/St is the general-purpose combination, Cu/Br and Cu/SSt for corrosion-matched or higher-strength service. Copper rivets set at lower forces than aluminium bodies of the same size — the load rows above are lower than the steel-body equivalents — so a substitution from Cu to Al changes both the corrosion picture and the strength check. State the body/mandrel combination on the RFQ exactly as the drawing prints it; the countersunk head needs the 90-degree csk hole prepared to match k max

Ordering & documentation

Documents

Shipments of DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for din en iso 16583 open end blind rivets, countersunk head, cu/st (break pull mandrel) is 10,000–50,000 pieces depending on size (applies to the standard sizes and finishes for din en iso 16583 open end blind rivets, countersunk head, cu/st (break pull mandrel); mixed, special or custom variants are quoted — final commercial terms per quotation) Standard production for din en iso 16583 open end blind rivets, countersunk head, cu/st (break pull mandrel) run 10–20 days. Quantities or variants of din en iso 16583 open end blind rivets, countersunk head, cu/st (break pull mandrel) outside the standard range are confirmed at quotation.

Storage & shipping

DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din en iso 16583 open end blind rivets, countersunk head, cu/st (break pull mandrel) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

What do the four load rows actually mean when qualifying a riveted joint?

They are four different tests: minimum shear and minimum tensile are what the set rivet must carry (the joint-design numbers); maximum mandrel break load is the upper bound of the setting force — above it the mandrel damages the joint instead of breaking cleanly; and head retention is a small load (15 to 25 N here) checking the countersunk head does not pull through the sheet after setting. The wide gap between working loads (760 to 2000 N shear) and mandrel break load (3000 to 5000 N) is the setting window: the tool must be capable of breaking a much stronger mandrel than the joint will ever see in shear. Qualify against the min rows, tool against the max row.

The table has no size labels on the columns — how do I read it?

The collected page prints the size ladder implicitly: read each column vertically by its d (shank) max/min rows, which give the four rivet sizes (≈3.0/3.2/4.0/4.8 class). Every other attribute in that column — head, mandrel, grip, hole, loads — belongs to that size. The source page also printed its mandrel-protrusion row (b) twice, once styled as a header; the duplicate was dropped and the grid copy kept, as the batch anomalyFlags note. When ordering, name the rivet by its d size and ISO 16583 designation — never by a column position.

What is the MOQ and lead time for DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel)?

Orders under this designation have a minimum order quantity of 10,000–50,000 pieces depending on size. Standard production ships in 10–20 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel) state?

State the full designation (DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel)), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel) inquiry

  • ✓ Identify blind, solid or structural rivet type and the applicable product standard.
  • ✓ Give rivet-body diameter and grip range for the complete material stack, plus the prepared-hole size.
  • ✓ Specify head style/clearance and state body and mandrel materials separately for blind rivets.
  • ✓ For load-bearing joints, provide required rivet-specific tensile and shear values; do not substitute a bolt property class.
  • ✓ State finish, quantity, destination and any lot-test or traceability documents required.
  • ✓ Factory-direct pricing for your DIN EN ISO 16583 Open End Blind Rivets, Countersunk Head, Cu/St (Break Pull Mandrel)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.