DIN 7338 Rivets for Brake and Clutch Linings

DIN 7338 rivets for brake and clutch linings, shank d1 3–10 mm — the countersunk-head solid rivet with a reduced shoulder shank that seats the friction lining in the shoe, with the collected head/shoulder/shank ladder and the matching fitting data (clearance hole, countersink, projection).

Last updated: 2026-11

Request a Quote

DIN 7338 Rivets for Brake and Clutch Linings in an industrial setting
Illustrative image redrawn from real DIN 7338 Rivets for Brake and Clutch Linings product references — not a photograph of stocked items.

Specifications

Brake and clutch linings are riveted, not bolted: a DIN 7338 rivet is a countersunk-head solid rivet whose shank is turned down below the nominal at the shoulder (d3 min., 2,85 mm at the 3 mm rivet rising to 9,75 mm at the 10 mm rivet) so the lining sits flat against the shoe while the rivet head pulls it down. The collected table runs shank d1 = 3 to 10 mm (h13) and carries per size the countersink base diameter d2 (h14/h15, 5,5 → 18 mm), the clearance-hole and countersink diameters the shoe needs (d4, and the fitting table d7 H12 / d9 H14), the shank under tolerance d10, the head geometry (height e, thickness k, fillet r), and the projection z1 after setting — given as two ladders because a longer rivet (l 22–40) projects differently than a short one (l 5–20). Reading order at the bench: drill the lining to d7 and countersink to d9 off the fitting table for the rivet size, set the rivet so the head sits under the lining countersink, and check the projection z1 matches the ladder for the length used — under-projection means a cold joint, over-projection means the set head stands proud and scores the drum. Materials (the lining rivet is typically a soft brass/aluminium or steel by application) and length ladders are not tabulated by the collected specification — per RFQ.

Standard DIN 7338 — rivets for brake linings and clutch linings (countersunk head, shouldered shank)
Size range Shank d1 3 – 10 mm (h13), six sizes in the collected ladder (3, 4, 5, 6, 8, 10)
Head / countersink d2: 5,5 → 18 mm (h14 at d1 3–5, h15 at 6–10 per the source tolerance split); head height e (max) 1,5 → 5 mm; thickness k 0,8 → 1,4 mm
Shoulder / shank d3 (min.) 2,85 → 9,75 mm; hole d4 (H13) 1,7 → 7,5 mm; shank under tolerance d10 1,66 → 7,18 mm
Fitting data Clearance hole d7 (H12) 3,1 → 10,5 mm; countersink d9 (H14) 6,5 → 19 mm; projection z1: 2,5–6 mm (l 5–20) / 6–7 mm (l 22–40)
Materials / length ladder Not tabulated by the collected specification — per RFQ (state lining material, shoe thickness and environment at quotation)
DIN 7338 rivets for brake and clutch linings — head, shoulder and shank geometry, shank d1 3–10 mmAll dimensions in millimetres, comma decimal separators preserved from the source. Row designations (d1, d2, d3, d4, d10, e, k, r, s, s´, t) and their tolerance classes are as printed by the source; the source does not expand the designations. Length ladder beyond the printed rows is not tabulated by the source — per RFQ. The fitting data (clearance hole, countersink, projection) is on the second table of this page.
Shank Dia. (d1 h13)Head Dia. (d2)Shoulder Dia. (d3 min.)Hole Dia. (d4 H13)Shank Under Tol. (d10)Head Height (e max.)Head Thick. (k)Fillet (r max.)ss´ min.Shoulder Length (t)
35,52,851,71,661,50,80,20,50,43,5
47,53,82,72,62210,30,50,44
59,54,83,53,422,510,30,60,54
611,55,84,24,1231,20,40,750,66
815,57,7565,1841,20,41,218
10189,757,57,1851,40,61,2110
  • Row 1 (3): The source splits the d2 tolerance across two cells ("tolerance | h14 | h15") for the 3–5 mm and 6–10 mm ranges; the table above carries the nominal d2 values with the tolerance note here. A stray length ladder row ("4 5 6 8 10 12") appears at the table tail with empty cells — treated as the source length list, not data, and not reproduced as a data row.
DIN 7338 rivets for brake and clutch linings — fitting data: clearance hole, countersink and projection, shank d1 3–10 mmAll dimensions in millimetres, comma decimal separators preserved from the source. d7 (H12) = clearance hole in the lined part; d9 (H14) = countersink diameter; z1 = approximate length of projection after setting, given as two ladders (l = 5 to 20, and l = 22 to 40 where returned).
Shank Dia. (d1)Clearance Hole (d7 H12)Countersink Dia. (d9 H14)Projection z1 (l = 5–20)Projection z1 (l = 22–40)
33,16,52,5-
44,28,53-
55,210,54,5-
66,312,556
88,416,556
1010,51967

Materials

  • Material specified per RFQ — brake/clutch rivets see heat and shear every cycle; state the application (drum, disc, clutch plate), the lining and the shoe material with the order

Ordering & documentation

Documents

Shipments of DIN 7338 Rivets for Brake and Clutch Linings are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 7338 Rivets for Brake and Clutch Linings orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 7338 Rivets for Brake and Clutch Linings), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for din 7338 rivets for brake and clutch linings is 10,000–50,000 pieces depending on size (applies to the standard sizes and finishes for din 7338 rivets for brake and clutch linings; mixed, special or custom variants are quoted — final commercial terms per quotation) Standard production for din 7338 rivets for brake and clutch linings run 10–20 days. Quantities or variants of din 7338 rivets for brake and clutch linings outside the standard range are confirmed at quotation.

Storage & shipping

DIN 7338 Rivets for Brake and Clutch Linings are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 7338 rivets for brake and clutch linings dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

How do I fit DIN 7338 lining rivets — what do I drill, and how do I judge the set?

Two tables off this page do the fitting work. The fitting table is the drill chart: for each rivet size, drill the lining at d7 (H12 — 3,1 mm for the 3 mm rivet up to 10,5 mm for the 10 mm) and countersink at d9 (H14 — 6,5 mm up to 19 mm), which sets how deep the countersunk head buries into the lining. The geometry table is the set check: after setting, the projection z1 tells you whether the joint closed — for short rivets (l 5–20) expect roughly 2,5–6 mm of projected shank to close into the head depending on size, for long rivets (l 22–40) expect 6–7 mm at the 6–10 mm sizes (the smaller sizes are not established for the long ladder — quote them explicitly). Two cautions: the d2 tolerance class splits across the series (h14 at 3–5 mm, h15 at 6–10 mm) and prints a stray length row at the table tail, both flagged under the table. What the table does not carry: rivet material (brass, aluminium and soft steel all appear in the trade by application), full length ladders and per-length stock — all RFQ lines, so state the application and lining stack at quotation.

What is the MOQ and lead time for DIN 7338 Rivets for Brake and Clutch Linings?

Orders under this designation have a minimum order quantity of 10,000–50,000 pieces depending on size. Standard production ships in 10–20 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN 7338 Rivets for Brake and Clutch Linings state?

State the full designation (DIN 7338), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 7338 Rivets for Brake and Clutch Linings inquiry

  • ✓ Identify blind, solid or structural rivet type and the applicable product standard.
  • ✓ Give rivet-body diameter and grip range for the complete material stack, plus the prepared-hole size.
  • ✓ Specify head style/clearance and state body and mandrel materials separately for blind rivets.
  • ✓ For load-bearing joints, provide required rivet-specific tensile and shear values; do not substitute a bolt property class.
  • ✓ State finish, quantity, destination and any lot-test or traceability documents required.
  • ✓ Factory-direct pricing for your DIN 7338 Rivets for Brake and Clutch Linings
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.