DIN 1052 Washers for Wood Constructions

DIN 1052 load-distribution washers for timber connections — nominal threads M12 to M24, the large-diameter plate washer that spreads a timber connector's clamping load over the wood surface, with the collected hole/outside-diameter/thickness ladder.

Last updated: 2026-11

Request a Quote

DIN 1052 Washers for Wood Constructions in an industrial setting
Illustrative image redrawn from real DIN 1052 Washers for Wood Constructions product references — not a photograph of stocked items.

Specifications

DIN 1052 washers are the load-spreading plates for heavy timber bolting: under a hex bolt or threaded rod drawing a timber joint tight, the washer's large outside diameter (58 mm at M12 up to 105 mm at M24) keeps the clamping pressure below the wood's perpendicular-to-grain bearing capacity, so the connector does not embed and lose preload as the timber seasons. The collected ladder covers the five sizes the standard tabulates — M12, M16, M20, M22, M24 — each with a single hole-diameter, outside-diameter and thickness value (thickness steps 6 mm at the small end to 8 mm from M20 up). Pair them with the timber connectors your joinery detail calls (threaded rods, hex bolts) and read the ladder straight off the table. Material grade and finish are not tabulated by the collected specification — per RFQ (state the timber treatment environment, since treated timber drives the coating choice).

Standard DIN 1052 — washers for wood constructions (load-distribution plate washers for timber connections)
Size range Nominal thread M12 – M24 (M12 / M16 / M20 / M22 / M24 tabulated)
Hole diameter d1: 14 – 27 mm, single value per size
Outside diameter dc: 58 – 105 mm, single value per size
Thickness h: 6 – 8 mm, single value per size
Material / finish Not tabulated by the collected specification — per RFQ
DIN 1052 washers for wood constructions - attribute rows per nominal thread (M12 - M24)All dimensions in millimetres. Attribute labels follow the source: d1 = hole diameter; dc = outside diameter; h = thickness. The source prints single values per size (no min/max split).
For Nominal Thread DiameterM12M16M20M22M24
d11418222527
dc58688092105
h66888

Materials

  • Material and finish specified per RFQ — plate washers for timber are typically plain or galvanized steel; state the timber treatment and exposure at quotation

Ordering & documentation

Documents

Shipments of DIN 1052 Washers for Wood Constructions are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 1052 Washers for Wood Constructions orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 1052 Washers for Wood Constructions), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 1052 Washers for Wood Constructions: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 1052 washers for wood constructions is 10,000 pieces (applies to the standard sizes and finishes for din 1052 washers for wood constructions; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 1052 washers for wood constructions run 3–7 days. Quantities or variants of din 1052 washers for wood constructions outside the standard range are confirmed at quotation.

Storage & shipping

DIN 1052 Washers for Wood Constructions are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 1052 washers for wood constructions dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why is the outside diameter so large on these washers?

Because the washer's job is bearing, not clearance. In a timber connection the bolt tension squeezes the washer into the wood surface, and wood carries roughly a fifth to a tenth of steel's allowable bearing stress perpendicular to the grain — so the load has to be spread. The collected ladder shows the proportion: at M20 the washer is 80 mm across on a 22 mm hole, more than three and a half hole-diameters of bearing face, and thickness grows to 8 mm so the plate itself does not dish under the load. Compare the plain-washer lines in this catalog (ISO 7089 / DIN 125) and their outside diameters are barely twice the hole — sized for steel-to-steel, not for wood. Finish and steel grade go on the RFQ: preservative-treated timber in particular dictates a compatible coating.

What is the MOQ and lead time for DIN 1052 Washers for Wood Constructions?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN 1052 Washers for Wood Constructions state?

State the full designation (DIN 1052), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 1052 Washers for Wood Constructions inquiry

  • ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
  • ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
  • ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
  • ✓ Describe the bearing surface or locking function, quantity per size and destination.
  • ✓ Factory-direct pricing for your DIN 1052 Washers for Wood Constructions
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.