Inch-Series Flat Washers — Type A and Type B (Narrow / Regular / Wide)
Inch-series flat washers in Type A and Type B narrow, regular and wide styles — ID and OD with printed tolerances and thickness max/min, sizes No.0 through 3 in, full 97-row ladder.
Last updated: 2026-11
Specifications
The inch flat-washer family splits by how much bearing area and clearance the joint needs, and the collected ladder prints that split directly as the Type A / Type B and narrow / regular / wide structure. Type B is the three-style series: narrow (smallest OD), regular (the general-purpose washer) and wide (maximum bearing area) — at 1 in, regular runs OD 2-1/2 while wide reaches 3 in, which is the difference between clearing a bolt head and spreading the load on a softer base material. Type A is a narrower product line: a single style through No.12 and a narrow/wide split from 1/4 up, printing its own thickness window. Every row of the source carries the same tolerance structure — ID and OD as a basic dimension with individual + and - tolerances, thickness as nominal with max/min — so a drawing check can be made against the actual acceptance window rather than a rounded nominal. The ladder runs from the No.0 screw-size washers through the large fractions to 3 in, 97 washer entries in total. Reading note: the collected source prints no standard number on the page itself — the type/style identity above is the printed product identity, and this page is registered on that basis.
| Product identity / scope | inch-series flat washers, Type A and Type B (narrow / regular / wide); sizes No.0, No.1, No.2, No.3, No.4, No.5, No.6, No.8, No.10, No.12, 1/4, 7/16, 9/16, 5/8, 3/4, 7/8, 1, 1 1/2, 1 3/4, 1 7/8, 2, 2 3/4 and 3 in on the source ladder (97 washer entries; intermediate fractions such as 5/16 and 3/8 are not printed by this source) |
|---|---|
| Type B styles | narrow / regular / wide at every size line — regular is the general-purpose OD, narrow minimizes OD where clearance rules, wide maximizes bearing area (1 in: OD basic 1.750 / 2.500 / 3.000) |
| Type A styles | single style ("-") through No.12; narrow/wide split from 1/4 up (1/4: OD basic 0.625 narrow, 0.734 wide); thickness prints its own nominal/max/min window (e.g. 0.065 nom, 0.080 max, 0.051 min at No.12 and 1/4 narrow) |
| Tolerance structure | ID and OD print basic + tolerance / - tolerance separately per row (typical +0.015/-0.005 in the small sizes stepping to +0.065/-0.010 at 2 3/4 and 3); thickness prints nominal with max/min — quote the acceptance window, not just the basic, on drawing checks |
| Largest sizes | 2 3/4 and 3 in: Type A single style with OD basic 5.250 / 5.500 and thickness nominal 0.259 / 0.284; Type B wide reaches OD basic 6.500 / 7.000 at thickness nominal 0.375 |
| Transcription note | the source calculator dump prints continuation rows with the size inherited; flattened to explicit rows without value changes, and the dump's empty trailing column dropped per row (anomaly recorded in the batch ledger) |
| Not tabulated | material, finish, MOQ, lead time and price — the last three are confirmed at quotation |
| Nominal size (in) | Type | Style | ID basic (in) | ID +tol (in) | ID -tol (in) | OD basic (in) | OD +tol (in) | OD -tol (in) | Thickness nominal (in) | Thickness max (in) | Thickness min (in) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| No.0 | Type A | - | 0.078 | 0.000 | 0.005 | 0.188 | 0.000 | 0.005 | 0.020 | 0.025 | 0.016 |
| No.0 | Type B | Narrow | 0.068 | 0.000 | 0.005 | 0.125 | 0.000 | 0.005 | 0.025 | 0.028 | 0.022 |
| No.0 | Type B | Regular | 0.068 | 0.000 | 0.005 | 0.188 | 0.000 | 0.005 | 0.025 | 0.028 | 0.022 |
| No.0 | Type B | Wide | 0.068 | 0.000 | 0.005 | 0.250 | 0.000 | 0.005 | 0.025 | 0.028 | 0.022 |
| No.1 | Type B | Narrow | 0.084 | 0.000 | 0.005 | 0.156 | 0.000 | 0.005 | 0.025 | 0.028 | 0.022 |
| No.1 | Type B | Regular | 0.084 | 0.000 | 0.005 | 0.219 | 0.000 | 0.005 | 0.025 | 0.028 | 0.022 |
| No.1 | Type B | Wide | 0.084 | 0.000 | 0.005 | 0.281 | 0.000 | 0.005 | 0.032 | 0.036 | 0.028 |
| No.2 | Type A | - | 0.094 | 0.000 | 0.005 | 0.250 | 0.000 | 0.005 | 0.020 | 0.025 | 0.016 |
| No.2 | Type B | Narrow | 0.094 | 0.000 | 0.005 | 0.188 | 0.000 | 0.005 | 0.025 | 0.028 | 0.022 |
| No.2 | Type B | Regular | 0.094 | 0.000 | 0.005 | 0.250 | 0.000 | 0.005 | 0.032 | 0.036 | 0.028 |
| No.2 | Type B | Wide | 0.094 | 0.000 | 0.005 | 0.344 | 0.000 | 0.005 | 0.032 | 0.036 | 0.028 |
| No.3 | Type B | Narrow | 0.109 | 0.000 | 0.005 | 0.219 | 0.000 | 0.005 | 0.025 | 0.028 | 0.022 |
| No.3 | Type B | Regular | 0.109 | 0.000 | 0.005 | 0.312 | 0.000 | 0.005 | 0.032 | 0.036 | 0.028 |
| No.3 | Type B | Wide | 0.109 | 0.008 | 0.005 | 0.406 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.4 | Type A | - | 0.125 | 0.008 | 0.005 | 0.312 | 0.008 | 0.005 | 0.032 | 0.040 | 0.025 |
| No.4 | Type B | Narrow | 0.125 | 0.000 | 0.005 | 0.250 | 0.000 | 0.005 | 0.032 | 0.036 | 0.028 |
| No.4 | Type B | Regular | 0.125 | 0.008 | 0.005 | 0.375 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.4 | Type B | Wide | 0.125 | 0.008 | 0.005 | 0.438 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.5 | Type B | Narrow | 0.141 | 0.000 | 0.005 | 0.281 | 0.000 | 0.005 | 0.032 | 0.036 | 0.028 |
| No.5 | Type B | Regular | 0.141 | 0.008 | 0.005 | 0.406 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.5 | Type B | Wide | 0.141 | 0.008 | 0.005 | 0.500 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.6 | Type A | - | 0.156 | 0.008 | 0.005 | 0.375 | 0.015 | 0.005 | 0.049 | 0.065 | 0.036 |
| No.6 | Type B | Narrow | 0.156 | 0.000 | 0.005 | 0.312 | 0.000 | 0.005 | 0.032 | 0.036 | 0.028 |
| No.6 | Type B | Regular | 0.156 | 0.008 | 0.005 | 0.438 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.6 | Type B | Wide | 0.156 | 0.008 | 0.005 | 0.562 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.8 | Type A | - | 0.188 | 0.008 | 0.005 | 0.438 | 0.015 | 0.005 | 0.049 | 0.065 | 0.036 |
| No.8 | Type B | Narrow | 0.188 | 0.008 | 0.005 | 0.375 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.8 | Type B | Regular | 0.188 | 0.008 | 0.005 | 0.500 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.8 | Type B | Wide | 0.188 | 0.008 | 0.005 | 0.625 | 0.015 | 0.005 | 0.063 | 0.071 | 0.056 |
| No.10 | Type A | - | 0.219 | 0.008 | 0.005 | 0.500 | 0.015 | 0.005 | 0.049 | 0.065 | 0.036 |
| No.10 | Type B | Narrow | 0.203 | 0.008 | 0.005 | 0.406 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.10 | Type B | Regular | 0.203 | 0.008 | 0.005 | 0.562 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.10 | Type B | Wide | 0.203 | 0.008 | 0.005 | 0.734 | 0.015 | 0.007 | 0.063 | 0.071 | 0.056 |
| No.12 | Type A | - | 0.250 | 0.015 | 0.005 | 0.562 | 0.015 | 0.005 | 0.065 | 0.080 | 0.051 |
| No.12 | Type B | Narrow | 0.234 | 0.008 | 0.005 | 0.438 | 0.008 | 0.005 | 0.040 | 0.045 | 0.036 |
| No.12 | Type B | Regular | 0.234 | 0.008 | 0.005 | 0.625 | 0.015 | 0.005 | 0.063 | 0.071 | 0.056 |
| No.12 | Type B | Wide | 0.234 | 0.008 | 0.005 | 0.875 | 0.015 | 0.007 | 0.063 | 0.071 | 0.056 |
| 1/4 | Type A | Narrow | 0.281 | 0.015 | 0.005 | 0.625 | 0.015 | 0.005 | 0.065 | 0.080 | 0.051 |
| 1/4 | Type A | Wide | 0.312 | 0.015 | 0.005 | 0.734 | 0.015 | 0.007 | 0.065 | 0.080 | 0.051 |
| 1/4 | Type B | Narrow | 0.281 | 0.015 | 0.005 | 0.500 | 0.015 | 0.005 | 0.063 | 0.071 | 0.056 |
| 1/4 | Type B | Regular | 0.281 | 0.015 | 0.005 | 0.734 | 0.015 | 0.007 | 0.063 | 0.071 | 0.056 |
| 1/4 | Type B | Wide | 0.281 | 0.015 | 0.005 | 1.000 | 0.015 | 0.007 | 0.063 | 0.071 | 0.056 |
| 7/16 | Type A | Narrow | 0.469 | 0.015 | 0.005 | 0.922 | 0.015 | 0.007 | 0.065 | 0.080 | 0.051 |
| 7/16 | Type A | Wide | 0.500 | 0.015 | 0.005 | 1.250 | 0.030 | 0.007 | 0.083 | 0.104 | 0.064 |
| 7/16 | Type B | Narrow | 0.469 | 0.015 | 0.005 | 0.875 | 0.015 | 0.007 | 0.063 | 0.071 | 0.056 |
| 7/16 | Type B | Regular | 0.469 | 0.015 | 0.005 | 1.125 | 0.015 | 0.007 | 0.063 | 0.071 | 0.056 |
| 7/16 | Type B | Wide | 0.469 | 0.015 | 0.005 | 1.469 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 9/16 | Type A | Narrow | 0.594 | 0.015 | 0.005 | 1.156 | 0.030 | 0.007 | 0.095 | 0.121 | 0.074 |
| 9/16 | Type A | Wide | 0.625 | 0.015 | 0.005 | 1.469 | 0.030 | 0.007 | 0.109 | 0.132 | 0.086 |
| 9/16 | Type B | Narrow | 0.594 | 0.015 | 0.005 | 1.125 | 0.015 | 0.007 | 0.063 | 0.071 | 0.056 |
| 9/16 | Type B | Regular | 0.594 | 0.015 | 0.005 | 1.469 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 9/16 | Type B | Wide | 0.594 | 0.015 | 0.005 | 2.000 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 5/8 | Type A | Narrow | 0.656 | 0.030 | 0.007 | 1.312 | 0.030 | 0.007 | 0.095 | 0.121 | 0.074 |
| 5/8 | Type A | Wide | 0.688 | 0.030 | 0.007 | 1.750 | 0.030 | 0.007 | 0.134 | 0.160 | 0.108 |
| 5/8 | Type B | Narrow | 0.656 | 0.030 | 0.007 | 1.250 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 5/8 | Type B | Regular | 0.656 | 0.030 | 0.007 | 1.750 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 5/8 | Type B | Wide | 0.656 | 0.030 | 0.007 | 2.250 | 0.030 | 0.007 | 0.160 | 0.174 | 0.146 |
| 3/4 | Type A | Narrow | 0.812 | 0.030 | 0.007 | 1.469 | 0.030 | 0.007 | 0.134 | 0.160 | 0.108 |
| 3/4 | Type A | Wide | 0.812 | 0.030 | 0.007 | 2.000 | 0.030 | 0.007 | 0.148 | 0.177 | 0.122 |
| 3/4 | Type B | Narrow | 0.812 | 0.030 | 0.007 | 1.375 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 3/4 | Type B | Regular | 0.812 | 0.030 | 0.007 | 2.000 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 3/4 | Type B | Wide | 0.812 | 0.030 | 0.007 | 2.500 | 0.030 | 0.007 | 0.160 | 0.174 | 0.146 |
| 7/8 | Type A | Narrow | 0.938 | 0.030 | 0.007 | 1.750 | 0.030 | 0.007 | 0.134 | 0.160 | 0.108 |
| 7/8 | Type A | Wide | 0.938 | 0.030 | 0.007 | 2.250 | 0.030 | 0.007 | 0.165 | 0.192 | 0.136 |
| 7/8 | Type B | Narrow | 0.938 | 0.030 | 0.007 | 1.469 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 7/8 | Type B | Regular | 0.938 | 0.030 | 0.007 | 2.250 | 0.030 | 0.007 | 0.160 | 0.174 | 0.146 |
| 7/8 | Type B | Wide | 0.938 | 0.030 | 0.007 | 2.750 | 0.030 | 0.007 | 0.160 | 0.174 | 0.146 |
| 1 | Type A | Narrow | 1.062 | 0.030 | 0.007 | 2.000 | 0.030 | 0.007 | 0.134 | 0.160 | 0.108 |
| 1 | Type A | Wide | 1.062 | 0.030 | 0.007 | 2.500 | 0.030 | 0.007 | 0.165 | 0.192 | 0.136 |
| 1 | Type B | Narrow | 1.062 | 0.030 | 0.007 | 1.750 | 0.030 | 0.007 | 0.100 | 0.112 | 0.090 |
| 1 | Type B | Regular | 1.062 | 0.030 | 0.007 | 2.500 | 0.030 | 0.007 | 0.160 | 0.174 | 0.146 |
| 1 | Type B | Wide | 1.062 | 0.030 | 0.007 | 3.000 | 0.030 | 0.007 | 0.160 | 0.174 | 0.146 |
| 1 1/2 | Type A | Narrow | 1.625 | 0.030 | 0.007 | 3.000 | 0.030 | 0.007 | 0.165 | 0.192 | 0.136 |
| 1 1/2 | Type A | Wide | 1.625 | 0.045 | 0.010 | 3.500 | 0.045 | 0.010 | 0.180 | 0.213 | 0.153 |
| 1 1/2 | Type B | Narrow | 1.562 | 0.030 | 0.007 | 2.750 | 0.030 | 0.007 | 0.160 | 0.174 | 0.146 |
| 1 1/2 | Type B | Regular | 1.562 | 0.045 | 0.010 | 3.500 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 1 1/2 | Type B | Wide | 1.562 | 0.045 | 0.010 | 4.000 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 1 3/4 | Type A | - | 1.875 | 0.045 | 0.010 | 4.000 | 0.045 | 0.010 | 0.180 | 0.213 | 0.153 |
| 1 3/4 | Type B | Narrow | 1.875 | 0.030 | 0.007 | 3.250 | 0.030 | 0.007 | 0.160 | 0.174 | 0.146 |
| 1 3/4 | Type B | Regular | 1.875 | 0.045 | 0.010 | 4.000 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 1 3/4 | Type B | Wide | 1.875 | 0.045 | 0.010 | 4.500 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 1 7/8 | Type A | - | 2.000 | 0.045 | 0.010 | 4.250 | 0.045 | 0.010 | 0.180 | 0.213 | 0.153 |
| 1 7/8 | Type B | Narrow | 2.000 | 0.045 | 0.010 | 3.500 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 1 7/8 | Type B | Regular | 2.000 | 0.045 | 0.010 | 4.250 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 1 7/8 | Type B | Wide | 2.000 | 0.045 | 0.010 | 4.750 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 2 | Type A | - | 2.125 | 0.045 | 0.010 | 4.500 | 0.045 | 0.010 | 0.180 | 0.213 | 0.153 |
| 2 | Type B | Narrow | 2.125 | 0.045 | 0.010 | 3.750 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 2 | Type B | Regular | 2.125 | 0.045 | 0.010 | 4.500 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 2 | Type B | Wide | 2.125 | 0.045 | 0.010 | 5.000 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 2 3/4 | Type A | - | 2.875 | 0.065 | 0.010 | 5.250 | 0.065 | 0.010 | 0.259 | 0.310 | 0.228 |
| 2 3/4 | Type B | Narrow | 2.875 | 0.045 | 0.010 | 5.000 | 0.045 | 0.010 | 0.250 | 0.266 | 0.234 |
| 2 3/4 | Type B | Regular | 2.875 | 0.065 | 0.010 | 6.000 | 0.065 | 0.010 | 0.375 | 0.393 | 0.357 |
| 2 3/4 | Type B | Wide | 2.875 | 0.065 | 0.010 | 6.500 | 0.065 | 0.010 | 0.375 | 0.393 | 0.357 |
| 3 | Type A | - | 3.125 | 0.065 | 0.010 | 5.500 | 0.065 | 0.010 | 0.284 | 0.327 | 0.249 |
| 3 | Type B | Narrow | 3.125 | 0.065 | 0.010 | 5.500 | 0.065 | 0.010 | 0.375 | 0.393 | 0.357 |
| 3 | Type B | Regular | 3.125 | 0.065 | 0.010 | 6.500 | 0.065 | 0.010 | 0.375 | 0.393 | 0.357 |
| 3 | Type B | Wide | 3.125 | 0.065 | 0.010 | 7.000 | 0.065 | 0.010 | 0.375 | 0.393 | 0.357 |
Materials
- Inch flat washers order in mild steel (self-colour or zinc-plated), stainless and hot-dip galvanized for exterior work — the source page is a dimension reference and does not print material stocks; state size (with fraction), type and style (e.g. "1/2 in Type B regular" reads directly off the table structure) and material on the RFQ. Commercial terms (MOQ, lead time, price) are confirmed at quotation.
Ordering & documentation
Documents
Shipments of Inch-Series Flat Washers — Type A and Type B (Narrow / Regular / Wide) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Inch-Series Flat Washers — Type A and Type B (Narrow / Regular / Wide) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (Inch-Series Flat Washers — Type A and Type B (Narrow / Regular / Wide)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for Inch-Series Flat Washers — Type A and Type B (Narrow / Regular / Wide): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for inch-series flat washers — type a and type b (narrow / regular / wide) is 10,000 pieces (applies to the standard sizes and finishes for inch-series flat washers — type a and type b (narrow / regular / wide); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for inch-series flat washers — type a and type b (narrow / regular / wide) run 3–7 days. Quantities or variants of inch-series flat washers — type a and type b (narrow / regular / wide) outside the standard range are confirmed at quotation.
Storage & shipping
Inch-Series Flat Washers — Type A and Type B (Narrow / Regular / Wide) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store inch-series flat washers — type a and type b (narrow / regular / wide) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Type B narrow, regular or wide — which style should the RFQ actually name?
Name the style explicitly rather than defaulting to regular, because the three styles differ most in the dimension that drives the joint: outer diameter. Regular is the default general-purpose washer sized to seat under the standard hex head of its nominal bolt. Narrow is the clearance solution — same hole, smaller OD — for packed assemblies, cast slots or retrofitting where a full OD would bridge into a neighbouring feature. Wide spreads the load: on soft base material (aluminium, timber, plastics, thin sheet) the extra bearing diameter is what prevents the washer from pulling through or dishing under clamp load. The table prints all three ODs per size with their tolerances, so the fastest check is to compare the wide OD against whatever feature sits next to the washer position — if it fits, wide buys margin for free; if not, regular; if it cannot even clear the bolt head's washer face, narrow.
Why does the ladder jump from 1/4 to 7/16 with no 5/16 or 3/8 sizes?
That is how the collected source prints its ladder — after 1/4 the next printed size is 7/16 — and the gaps are carried as printed rather than filled by assumption. The practical reading: the source documents the washer entries it documents, and intermediate screw/bolt sizes may be covered by other series (the metric flat-washer pages in this catalog, for instance, run an unbroken metric ladder). If your drawing calls out a 5/16 or 3/8 washer against this type/style structure, treat the exact dimensions as a quotation confirmation rather than reading across from neighbouring sizes — washer tolerances are per-size windows, and an interpolated OD would not carry a real acceptance window.
The table carries + and - tolerances per column — how should incoming inspection use them?
Each washer entry prints a basic ID with its own +tolerance and -tolerance, a basic OD likewise, and a thickness as nominal/max/min — three independent acceptance windows per row, not one. Incoming checks therefore read: hole diameter must fall inside the ID basic-plus-minus window (it is the fit over the bolt that matters, so the ID window is the go/no-go), OD must stay within its window only where a clearance or bearing-area constraint exists on the drawing, and thickness is the clamp-length and load-distribution variable — at the large sizes the windows widen (thickness nominal 0.375 at 2 3/4 Type B regular with max/min 0.393/0.357), which is material enough to shift a stack-up. Checking against the printed windows rather than the basic number avoids rejecting parts that are inside tolerance.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Inch-Series Flat Washers — Type A and Type B (Narrow / Regular / Wide) inquiry
- ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
- ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
- ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
- ✓ Describe the bearing surface or locking function, quantity per size and destination.
- ✓ Factory-direct pricing for your Inch-Series Flat Washers — Type A and Type B (Narrow / Regular / Wide)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support