DIN 436 Square Washers for Timber Bolts
DIN 436 square washers, M10 to M52 — the wide square plate washer used under hex bolts in timber and general construction — with the full collected 15-size table: bore, width across flats, thickness limits and the source's reference mass per 1000 units.
Last updated: 2026-11
Specifications
DIN 436 is the square washer that goes under a hex bolt head or nut when the bearing surface is soft or oversized: timber frames, sandwich panels, masonry plates and general construction steelwork. The square form covers far more area than a round washer of the same stock, spreading the clamp load so the bolt does not pull into the wood or crush the substrate, and the flat square edges bridge oversized holes. The collected table runs M10 to M52 in the large end of the series — bore d (min = nominal size / max), width across flats s (max = nominal size / min), the h thickness triple (Nominal Size / max / min), and the source's reference mass per 1000 units, the figure bulk timber-hardware purchasers price the line from. For the chamfered bore variant used with washer-faced bolts see DIN 436's sibling specifications; for the taper-washer counterpart that seats on channel and I-section flanges, see DIN 434 on this site. Materials and finishes are not printed by the collected specification and stay per RFQ.
| Standard | DIN 436 — square washers (product grade C), for hex head bolts and nuts |
|---|---|
| Series | M10 – M52 (15 sizes tabulated) |
| Tabulated geometry | Per size: bore d (min=nominal size / max), width across flats s (max=nominal size / min), thickness h (Nominal Size / max / min), reference mass per 1000 units ≈ kg |
| Function | Wide square bearing plate — spreads clamp load on timber and soft substrates, bridges oversized holes |
| Family note | Taper-washer counterpart for U-sections DIN 434; for I-sections DIN 435 |
| Materials / strength | Not tabulated by the collected specification — per RFQ (material and finish per drawing callout) |
| For Nominal Thread Diameter | d — min=nominal size | d — max | s — max=nominal size | s — min | h — Nominal Size | h — max | h — min | per 1000 units ≈ kg |
|---|---|---|---|---|---|---|---|---|
| M10 | 11 | 11.43 | 30 | 28.7 | 3 | 3.6 | 2.4 | 20 |
| M12 | 13.5 | 13.93 | 40 | 38.4 | 4 | 4.6 | 3.4 | 45.7 |
| M16 | 17.5 | 18.2 | 50 | 48.4 | 5 | 6 | 4 | 88.7 |
| M20 | 22 | 22.84 | 60 | 58.1 | 5 | 6 | 4 | 126 |
| M22 | 24 | 24.84 | 70 | 68.1 | 6 | 7 | 5 | 209 |
| M24 | 26 | 26.84 | 80 | 78.1 | 6 | 7 | 5 | 275 |
| M27 | 30 | 30.84 | 90 | 87.8 | 6 | 7 | 5 | 348 |
| M30 | 33 | 34 | 95 | 92.8 | 6 | 7 | 5 | 385 |
| M33 | 36 | 37 | 100 | 97.8 | 6 | 7 | 5 | 423 |
| M36 | 39 | 40 | 110 | 107.8 | 8 | 9.2 | 6.8 | 685 |
| M39 | 42 | 43 | 125 | 122.5 | 8 | 9.2 | 6.8 | 895 |
| M42 | 45 | 46 | 135 | 132.5 | 8 | 9.2 | 6.8 | 1050 |
| M45 | 48 | 49 | 140 | 137.5 | 8 | 9.2 | 6.8 | 1120 |
| M48 | 52 | 53.2 | 150 | 147.5 | 10 | 11.2 | 8.8 | 1600 |
| M52 | 56 | 57.2 | 160 | 157.5 | 10 | 11.2 | 8.8 | 1820 |
Materials
- Material and finish specified per RFQ — the collected specification table covers geometry and reference mass only
Ordering & documentation
Documents
Shipments of DIN 436 Square Washers for Timber Bolts are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 436 Square Washers for Timber Bolts orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 436 Square Washers for Timber Bolts), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 436 Square Washers for Timber Bolts: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 436 square washers for timber bolts is 10,000 pieces (applies to the standard sizes and finishes for din 436 square washers for timber bolts; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 436 square washers for timber bolts run 3–7 days. Quantities or variants of din 436 square washers for timber bolts outside the standard range are confirmed at quotation.
Storage & shipping
DIN 436 Square Washers for Timber Bolts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 436 square washers for timber bolts dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
When does a timber bolt need a square washer instead of a round one?
When the contact face cannot take a point load. Round washers dig into soft timber or thin plate as the joint is tightened; the square washer's larger footprint spreads the same clamp load over more surface, which is why it is the standard companion to coach bolts and hex timber bolts in frame construction. It also covers slotted or oversized holes that a round washer would pull through. Match the washer to the bolt size — the tabulated width across flats grows with the series — and check the substrate: on steel flanges that are sloped, a taper washer is the right part instead.
What is the MOQ and lead time for this washer type?
The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Common sizes are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 436 Square Washers for Timber Bolts inquiry
- ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
- ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
- ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
- ✓ Describe the bearing surface or locking function, quantity per size and destination.
- ✓ Factory-direct pricing for your DIN 436 Square Washers for Timber Bolts
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support