DIN 5406 MB Lockwashers for Rolling Bearings

DIN 5406 MB lockwashers (safety plates) for rolling bearing locknuts, shaft diameters 10 to 200: inner/outer tabs, e/f/b1 geometry, thickness s and mass — 2011 and 1993 editions.

Last updated: 2026-11

Request a Quote

DIN 5406 MB Lockwashers for Rolling Bearings in an industrial setting
Illustrative image redrawn from real DIN 5406 MB Lockwashers for Rolling Bearings product references — not a photograph of stocked items.

Specifications

DIN 5406 MB is the lockwasher that makes a bearing locknut positive: the inner tongue seats in the shaft keyway, the nut tightens over it, and one of the outer tabs bends into a nut slot to stop rotation absolutely — no friction, no prevailing torque, just positive metal engagement. The collected 04/2011-edition table runs the MB series across shaft diameters d1 10 to 200 (with the doubled d1 values in the ladder, e.g. 120; 120 — the source's own print for the two washer groups per size, carried verbatim) giving the tab geometry e, f and b1, thickness s min. and the mass per 1000 pcs; the superseded 1993 edition is transcribed as a second table alongside. The washer orders as a system with the locknut (ISO 2982 — registered here) and the shaft keyway: the tongue width b1/e must match the keyway, which is why these are ordered by shaft size, not by bolt thread.

Standard / scope DIN 5406 MB lockwashers for rolling bearings — shaft diameters d1 10 to 200, edition 04/2011; superseded 1993 edition transcribed as a separate table
Tab geometry e, f and b1 per size — the outer tab set that bends into the locknut slots, and the keyway-engagement dimensions
Thickness s s min. per size (2.5 at the 200 end) — the plate gauge that must spring without cracking on tab bending
Ladder note Doubled d1 values (120; 120 … 200; 200) printed in the source ladder, carried verbatim — the washer groups per shaft size
Mass Approximate kg per 1000 pcs per size (21.4 at the 200 end); matching locknuts per ISO 2982 (registered separately)
Not tabulated Material/hardness, keyway tolerance, finish — per RFQ
DIN 5406 MB lockwashers — 04/2011 edition, geometry by shaft diameter d1Dimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
d1d2d3efb1s min.≈ weigth in kg x1000 pcs
102113.538.5310.131
122517310.5310.192
152821413.5410.253
173224415.5410.313
203626418.5410.35
254232523.051.250.64
304938527.551.250.78
355744632.551.251.04
406250637.561.251.23
456956642.561.251.52
507461647.561.251.6
558167852.571.51.96
608673857.571.52.53
659279862.571.52.9
709885866.581.53.34
7510490871.581.53.56
80112951076.581.754.64
851191021081.581.755.24
901261081086.5101.756.23
951331131291.5101.756.7
1001421201296.5101.757.65
10514512612100.5121.758.26
11015413312105.5121.759.4
11515913714110.512210.8
120151135141151227.7
1201641381411512210.5
1251701481412012211.8
130161145141251228.7
1301751491412512211.3
1351851601613014214.4
1401711551613512210.9
1401921601613514214.2
1501881701614514216.8
1502051711614514211.3
15521218216147.5162.515.5
16019918018154142.520.9
16021718218154162.516.2
16522219318157.5162.522.9
17021119018164162.524.1
17023219318164162.517
18022120020174162.524.7
18024220320174182.518
19023121020184162.526.8
19025221420184182.520.5
20024822220194182.527.8
20026222620194182.521.4
  • Source spanning title row carried verbatim: "Dimensions in mm - source DIN 5406 Publication date: 04/2011".
DIN 5406 MB lockwashers — superseded 1993 edition, geometry by shaft diameter d1Dimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
d1d2d3efb1s min.≈ weigth in kg x1000 pcs
102113.538.5310.131
122517310.5310.192
152821413.5410.253
173224415.5410.313
203626418.5410.35
254232523.051.250.64
304938527.551.250.78
355744632.551.251.04
406250637.561.251.23
456956642.561.251.52
507461847.561.251.6
558167852.571.51.96
608673857.571.52.53
659279862.571.52.9
709885866.581.53.34
75104901071.581.53.56
80112951076.581.754.64
851191021081.581.755.24
901261081086.5101.756.23
951331131291.5101.756.7
1001421201296.5101.757.65
10514512612100.5121.758.26
11015413312105.5121.759.4
11515913712110.512210.8
120151135141151227.7
1201641381411512210.5
1251701481412012211.8
130161145141251228.7
1301751491412512211.3
1351851601413014214.4
1401711551613512210.9
1401921601613514214.2
1501881701614514216.8
1502051711614514211.3
15521218216147.5162.515.5
16019918018154142.520.9
16021718218154162.516.2
16522219318157.5162.522.9
17021119018164162.524.1
17023219318164162.517
18022120020174162.524.7
18024220320174182.518
19023121020184162.526.8
19025221420184182.520.5
20024822220194182.527.8
20026222620194182.521.4
  • Source spanning title row carried verbatim: "Dimensions in mm - source DIN 5406 Publication date: 1993".

Materials

  • MB lockwashers order in spring-grade steel — the tabs bend and re-bend in service, so the plate needs the right temper, not just thickness; stainless versions for corrosive plants at reduced re-bend life. Order by shaft diameter with the locknut call-out, state the shaft keyway width, and say how many re-tightening cycles the joint expects: each re-tightening re-bends a new tab, and the tab count in e/f is the budget

Ordering & documentation

Documents

Shipments of DIN 5406 MB Lockwashers for Rolling Bearings are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 5406 MB Lockwashers for Rolling Bearings orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 5406 MB Lockwashers for Rolling Bearings), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 5406 MB Lockwashers for Rolling Bearings: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 5406 mb lockwashers for rolling bearings is 10,000 pieces (applies to the standard sizes and finishes for din 5406 mb lockwashers for rolling bearings; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 5406 mb lockwashers for rolling bearings run 3–7 days. Quantities or variants of din 5406 mb lockwashers for rolling bearings outside the standard range are confirmed at quotation.

Storage & shipping

DIN 5406 MB Lockwashers for Rolling Bearings are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 5406 mb lockwashers for rolling bearings dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why use a lockwasher when prevailing-torque locknuts exist?

Because the two locking principles fail differently, and bearings sit where that matters. A prevailing-torque nut loses lock if it backs off even a fraction of a turn repeatedly under vibration cycles; the MB washer cannot back off at all — the bent tab is a mechanical stop, and unlocking requires deliberately bending the tab back. That is why bearing arrangements on shafts that reverse, shock or see maintenance re-tightening standardized on DIN 5406 + locknut. The costs are the keyway (the shaft must carry it) and the tab budget — every re-tightening consumes the next tab. High-vibration, reversing or safety-critical spindles take the washer; static, lightly loaded positions can accept the nut alone.

Why does the ladder print each large size twice (120; 120 … 200; 200)?

That doubled print is how the source table lists the larger shaft sizes — two washer entries per nominal diameter, carried verbatim in the grid and flagged, not merged. Read the full row set per size: the two entries share the nominal d1 but carry their own e/f/b1 tab geometry, which corresponds to the different locknut slot groups a big shaft can serve. The practical discipline: order the washer by the full locknut call-out (standard designation plus shaft size), not by d1 alone — the tab geometry must match the nut you bought, and at the doubled sizes the d1 alone does not identify a unique washer. We match washer to locknut per the tables on every order.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 5406 MB Lockwashers for Rolling Bearings inquiry

  • ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
  • ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
  • ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
  • ✓ Describe the bearing surface or locking function, quantity per size and destination.
  • ✓ Factory-direct pricing for your DIN 5406 MB Lockwashers for Rolling Bearings
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.