ISO 7094 Washers for Timber Constructions
ISO 7094 washers for use in timber constructions — large-diameter flat washers M5 to M36 (plus non-preferred M14–M33) that spread bolt loads in wood, with the collected preferred and non-preferred d1/d2/h ladders.
Last updated: 2026-11
Specifications
ISO 7094 is the timber-construction washer: a large-diameter, relatively thick flat washer whose whole job is to spread a bolt's clamping load across enough wood surface that the washer does not embed as the timber seasons and the joint loosens. The collected source splits the ladder into preferred sizes (M5 to M36: for example M12 with a 44 mm outside diameter and 4 mm nominal thickness, M20 at 72 mm and 6 mm) and a non-preferred panel (M14, M18, M22, M27, M33), both tabulated with bore min/max, outside min/max and thickness min/max. Compare the dedicated DIN 1052 timber page in this catalog: ISO 7094 runs a much longer size ladder down into the small-bolt range, while DIN 1052 concentrates on the heavy-connector gauges. Read the thickness column against your embedment concern — 6 mm nominal at M20 here against 3 mm on the normal ISO 7089 series is the difference between a washer that keeps its flat and one that dishes into the grain. Material and finish are not tabulated by the collected specification — per RFQ (timber treatment drives the coating choice, so name the preservative or exposure at quotation).
| Standard | ISO 7094 — plain washers for use in timber constructions |
|---|---|
| Size range | Preferred M5 – M36; non-preferred M14 / M18 / M22 / M27 / M33 (two source panels) |
| Hole diameter | d1: nominal min./max. per thread (e.g. M12: 13,5 / 13,93 mm) |
| Outside diameter | d2: nominal max./min. per thread (e.g. M12: 44 / 42,4 mm) |
| Thickness | h: nominal/max./min. per thread (e.g. M12: 4 / 4,6 / 3,4 mm) |
| Material / finish | Not tabulated by the collected specification — per RFQ |
| For thread | d1 nominal min. | d1 max. | d2 nominal max. | d2 min. | h nominal | h max. | h min. |
|---|---|---|---|---|---|---|---|
| M5 | 5,5 | 5,8 | 18 | 16,9 | 2 | 2,3 | 1,7 |
| M6 | 6,6 | 6,96 | 22 | 20,7 | 2 | 2,3 | 1,7 |
| M8 | 9 | 9,36 | 28 | 26,7 | 3 | 3,6 | 2,4 |
| M10 | 11 | 11,43 | 34 | 32,4 | 3 | 3,6 | 2,4 |
| M12 | 13,5 | 13,93 | 44 | 42,4 | 4 | 4,6 | 3,4 |
| M16 | 17,5 | 18,2 | 56 | 54,1 | 5 | 6 | 4 |
| M20 | 22 | 22,84 | 72 | 70,1 | 6 | 7 | 5 |
| M24 | 26 | 26,84 | 85 | 82,8 | 6 | 7 | 5 |
| M30 | 33 | 34 | 105 | 102,8 | 6 | 7 | 5 |
| M36 | 39 | 40 | 125 | 122,5 | 8 | 9,2 | 6,8 |
| For thread | d1 nominal min. | d1 max. | d2 nominal max. | d2 min. | h nominal | h max. | h min. |
|---|---|---|---|---|---|---|---|
| M14 | 15,5 | 15,93 | 50 | 48,1 | 4 | 4,6 | 3,4 |
| M18 | 20 | 20,84 | 60 | 58,1 | 5 | 6 | 4 |
| M22 | 24 | 24,84 | 80 | 78,1 | 6 | 7 | 5 |
| M27 | 30 | 30,84 | 98 | 95,8 | 6 | 7 | 5 |
| M33 | 36 | 37 | 115 | 112,8 | 8 | 9,2 | 6,8 |
Materials
- Material and finish specified per RFQ — state the timber treatment (preservative-treated, CCA, exterior exposure) so a compatible coating is confirmed at quotation
Ordering & documentation
Documents
Shipments of ISO 7094 Washers for Timber Constructions are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 7094 Washers for Timber Constructions orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ISO 7094 Washers for Timber Constructions), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for ISO 7094 Washers for Timber Constructions: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for iso 7094 washers for timber constructions is 10,000 pieces (applies to the standard sizes and finishes for iso 7094 washers for timber constructions; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 7094 washers for timber constructions run 3–7 days. Quantities or variants of iso 7094 washers for timber constructions outside the standard range are confirmed at quotation.
Storage & shipping
ISO 7094 Washers for Timber Constructions are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 7094 washers for timber constructions dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
ISO 7094 or DIN 1052 — which timber washer do I order?
Both spread load into wood; the ladders decide it. ISO 7094 covers the general timber-bolting range from M5 (18 mm outside diameter) up to M36 (125 mm), so it is the choice for ordinary bolted timber connections and for small-diameter fixings where the dedicated timber washer has no size. DIN 1052 in this catalog starts at M12 and is sized for the heavy timber-connector joints of the building standard of the same name — bigger plates, fewer sizes. Compare at M12: 44 mm outside and 4 mm thickness on the ISO ladder, 58 mm and 6 mm on the DIN 1052 ladder — the heavier the connector, the more plate you want. Neither collected table names steel grade or coating, and treated timber makes the finish choice load-bearing in its own right, so both stay per RFQ.
What is the MOQ and lead time for ISO 7094 Washers for Timber Constructions?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for ISO 7094 Washers for Timber Constructions state?
State the full designation (ISO 7094), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ISO 7094 Washers for Timber Constructions inquiry
- ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
- ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
- ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
- ✓ Describe the bearing surface or locking function, quantity per size and destination.
- ✓ Factory-direct pricing for your ISO 7094 Washers for Timber Constructions
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support