DIN 128B Spring Washers Type B (Wave)
DIN 128B spring washers Type B — the wave (wavy-disc) spring washer — sizes 2 to 100 with the full collected 27-size table across 9 block tables: bore d, wave section n, material thickness h and loaded height H with their tolerance bands, plus the source's reference mass per 1000 units.
Last updated: 2026-11
Specifications
DIN 128B is the wave spring washer: a flat disc formed into a multi-lobed sine wave, so it compresses evenly on several crests at once. Where the curved Type A bow springs on a single crown, the wave form distributes the spring stroke around the whole circumference — a lower, more centred reaction and less tilt under the nut, which matters on large diameters and on joints where a single-crown washer would rock. The collected table runs sizes 2 to 100 in nine block tables — a wider reach than Type A, which stops at 36 — tabulating per size: the bore d with min/max limits, the wave section n (Nominal / min / max), the material thickness h (Nominal / min / max), and the loaded height H with min/max limits — the compressed height at full clamp. The weight rows print a "≈" reference marker before each value; they are carried here as reference, not specification. The curved counterpart is DIN 128A. Materials and finishes are not printed by the collected specification and stay per RFQ.
| Standard | DIN 128B — spring washers Type B, wave (multi-lobed) form; curved counterpart DIN 128A |
|---|---|
| Series | 2 – 100 nominal diameter (27 sizes across 9 block tables) |
| Tabulated geometry | Per size: bore d (min / max), wave section n (Nominal / min / max), material thickness h (Nominal / min / max), loaded height H (min / max), reference mass per 1000 units ≈ kg (≈ reference marker as printed) |
| Dimensions at size 5 | d 5.1–5.4; n nominal 1.8 (max 1.9 / min 1.7); h nominal 1 (max 1.1 / min 0.9); H 1.5–1.7; weight ≈ 0.3 kg/1000 |
| Dimensions at size 12 | d 12.2–12.7; n nominal 4 (max 4.2 / min 3.8); h nominal 2.1 (max 2.25 / min 1.95); H 3.35–3.65; weight ≈ 3.2 kg/1000 |
| Dimensions at size 48 | d 49–50.5; n nominal 12 (max 12.25 / min 11.75); h nominal 7 (max 7.25 / min 6.75); H 12–13; weight ≈ 123 kg/1000 |
| Materials / strength | Not tabulated by the collected specification — per RFQ (spring material and finish per drawing callout) |
Materials
- Material and finish specified per RFQ — the collected specification table covers geometry and reference mass only
Ordering & documentation
Documents
Shipments of DIN 128B Spring Washers Type B (Wave) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 128B Spring Washers Type B (Wave) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 128B Spring Washers Type B (Wave)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 128B Spring Washers Type B (Wave): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 128b spring washers type b (wave) is 10,000 pieces (applies to the standard sizes and finishes for din 128b spring washers type b (wave); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 128b spring washers type b (wave) run 3–7 days. Quantities or variants of din 128b spring washers type b (wave) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 128B Spring Washers Type B (Wave) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 128b spring washers type b (wave) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Why choose the wave form over the curved Type A?
Stability on larger and flatter stacks. The wave reacts on several crests at the same time, so the spring force stays centred instead of tipping across a single crown — on wide diameters a curved washer can rock under the nut and load one side of the bearing face. The collected tables show the wave series also reaches further: sizes to 100 nominal against Type A stopping at 36. Both forms lock by elastic force rather than edge bite, so the choice between them is about load distribution and size availability, not surface marking.
The size ladder runs to 100 — what changes at the top of the table?
The section stops growing. From size 56 upward the collected table holds n at 14 and h at 8 with H 14–15.5 across the whole upper block — the wave simply widens with the bore while the spring section stays constant, which keeps the spring rate in a predictable band as the disc gets larger. Practical consequence: the very large sizes give less spring travel per unit load than the jump in diameter suggests, and for heavy joints you should confirm the compressed height H (14–15.5 mm in the upper block) against the grip stack rather than scaling from smaller sizes.
What is the MOQ and lead time for this washer type?
Minimum order quantity is 1,000 pieces per item. Standard samples ship in 3–5 days, bulk standard parts in 15–25 days, and custom OEM parts in 30–45 days. Common sizes are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 128B Spring Washers Type B (Wave) inquiry
- ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
- ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
- ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
- ✓ Describe the bearing surface or locking function, quantity per size and destination.
- ✓ Factory-direct pricing for your DIN 128B Spring Washers Type B (Wave)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support