DIN 703 Collars, Heavy Series (d1 24 – 120)

DIN 703 collars heavy series — thick Shoulderring/collar washers dimensioned d1 (H8 bore) 24 to 120, ring width b (js14) 22 to 32, outer diameter d2 (h13) 56 to 160, with the matching socket set screw (DIN 914 M10x16 to M16x25) tabulated per row for shaft-end bearing and positioning duties.

Last updated: 2026-11

Request a Quote

DIN 703 Collars, Heavy Series (d1 24 – 120) in an industrial setting
Illustrative image redrawn from real DIN 703 Collars, Heavy Series (d1 24 – 120) product references — not a photograph of stocked items.

Specifications

A DIN 703 collar is not a flat washer: it is a thick, closely-toleranced ring that rides on a shaft end to locate bearings, gears or pulleys axially, and it is locked there by a socket set screw bearing on the shaft — which is why the source prints the set-screw column (DIN 914, M10x16 up to M16x25) right beside the collar dimensions instead of leaving the mating part to guesswork. The "heavy series" in the title is visible in the numbers: ring widths b run 22 to 32 mm across the whole ladder and bores carry H8 tolerances, so the collar seats on the shaft with a real fit rather than a loose slip. The collected grid runs d1 24 to 120 in one continuous ladder (33 rows), d2 from 56 to 160, with the set screw stepping M10x16 → M12x20 → M16x20 → M16x25 as the bore grows. Reading notes before engineering use: the source legend defines d3 as "diameter of socket set screw" while the d3 table column carries thread designations (M10 to M16) and the set-screw sizes live in their own "screw DIN 914" column — the mismatch is the source's own and is flagged, not silently resolved; and the table title prints "Dimensions setting rings DIN 703" (sic). Materials as printed: steel and stainless A2/A4; per RFQ for anything beyond that.

Standard / scope DIN 703 collars heavy series (source title as printed: "DIN 703 - Collars heavy series"); table title prints "Dimensions setting rings DIN 703" (sic)
Bore (d1, H8) 24 to 120, 33 tabulated sizes in one ladder with H8 bore tolerance per the source header
Ring width (b, js14) 22 (d1 24-38) / 28 (d1 40-65) / 32 (d1 68-120), js14 tolerance per the source header
Outer diameter (d2, h13) 56 to 160, h13 tolerance per the source header; steps e.g. 56 (d1 24-26), 125 (d1 80-90), 160 (d1 110-120)
Set screw (DIN 914) tabulated per row: M10x16 (d1 24-38), M12x20 (d1 40-65), M16x20 (d1 68-90), M16x25 (d1 95-120); d3 column carries the thread (M10/M12/M16)
Materials (as printed) Steel: steel; Stainless: A2, A4; Plastic: -; Non Ferrous: -; Thread: - (source makings block verbatim)
Equivalents (as printed) Equivalent norms: PN 85102
Setting rings DIN 703 (collars heavy series — table title as printed)dimensions in mm; tolerances per the source header: d1 H8, b js14, d2 h13
d1 H 8b js 14d2 h13d3screw DIN 914
242256M10M10x16
252256M10M10x16
262256M10M10x16
282263M10M10x16
302263M10M10x16
322263M10M10x16
342270M10M10x16
352270M10M10x16
362270M10M10x16
382270M10M10x16
402880M12M12x20
422880M12M12x20
452880M12M12x20
482880M12M12x20
502890M12M12x20
522890M12M12x20
552890M12M12x20
562890M12M12x20
5828100M12M12x20
6028100M12M12x20
6328100M12M12x20
6528100M12M12x20
6832110M16M16x20
7032110M16M16x20
7232110M16M16x20
7532110M16M16x20
8032125M16M16x20
8532125M16M16x20
9032125M16M16x20
9532140M16M16x25
10032140M16M16x25
11032160M16M16x25
12032160M16M16x25
  • the source legend reads "d3 - diameter of socket set screw" (double space as captured) while the d3 column carries thread designations (M10/M12/M16) and the set-screw part numbers sit in the 'screw DIN 914' column — legend/table mismatch carried verbatim, not adjudicated; resolve drawing-critical uses against the standard document.
  • the source table title prints "Dimensions setting rings DIN 703" while the page title prints "DIN 703 - Collars heavy series" — both are the source's own naming and neither is normalized here.
  • the set-screw ladder steps M10x16 → M12x20 → M16x20 → M16x25 across the d1 range; the d1 68-90 band prints M16x20 and d1 95-120 prints M16x25 — as printed, per row.

Materials

  • The source makings block prints exactly two material families — Steel: steel, and Stainless: A2, A4 — so this page claims no more than that. Collars work by friction and set-screw bite on the shaft, so the practical RFQ question is not just material but face condition and the matching set-screw: state bore d1 (the ladder here), material class (plain steel vs A2/A4 stainless for corrosive or washdown duty), whether the DIN 914 set screw is supplied fitted, and quantity per size. Hardened or special-face collars, non-ferrous versions (the source prints "-" for Non Ferrous) and sizes outside the 24-120 ladder are confirmed at quotation.

Ordering & documentation

Documents

Shipments of DIN 703 Collars, Heavy Series (d1 24 – 120) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 703 Collars, Heavy Series (d1 24 – 120) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 703 Collars, Heavy Series (d1 24 – 120)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 703 Collars, Heavy Series (d1 24 – 120): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 703 collars, heavy series (d1 24 – 120) is 10,000 pieces (applies to the standard sizes and finishes for din 703 collars, heavy series (d1 24 – 120); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 703 collars, heavy series (d1 24 – 120) run 3–7 days. Quantities or variants of din 703 collars, heavy series (d1 24 – 120) outside the standard range are confirmed at quotation.

Storage & shipping

DIN 703 Collars, Heavy Series (d1 24 – 120) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 703 collars, heavy series (d1 24 – 120) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

The legend calls d3 the "diameter of socket set screw", but the d3 column lists M10/M12/M16 threads — which is it?

The source contradicts itself and this page carries both prints verbatim rather than adjudicating: the legend line reads "d3 - diameter of socket set screw" (spacing as captured), while the d3 table column carries thread designations (M10, M12, M16) and the actual set-screw part numbers (M10x16 … M16x25) sit in their own "screw DIN 914" column. The self-consistent reading is that d3 indexes the set-screw thread matched to the collar size and the screw column gives the full DIN 914 part — but that is a reading, not a source statement, so for a drawing-critical use resolve it against the standard document and state the intended set screw explicitly on the RFQ.

Why does a collar page tabulate a set screw — and do I have to buy them together?

Because the collar only does its job once the set screw locks it: DIN 703 collars are positioned on shaft ends by a socket set screw in the collar's boss (the source tabulates the DIN 914 part per row — M10x16 on the small bores through M16x25 at d1 95-120), so the screw size is part of the collar's dimension chain, not an accessory afterthought. Whether screw and collar ship together is a supply question, not a dimension one: the source only fixes the pairing, so state on the RFQ whether you want the DIN 914 screw supplied with each collar (and in which material class — mixing an A4 collar with a plain-steel screw is a corrosion mismatch).

DIN 703 or a plain large-OD washer — when does the distinction matter?

When the ring has to hold a position, not just spread a load. A plain washer (DIN 125/126/9021-class parts on this site) is thin and untoleranced in function: it distributes clamp load under a nut or bolt head. A DIN 703 collar is thick (b 22-32 across the range), bore-toleranced (H8) and paired with a set screw — it is a positioning element on a shaft end, typically retaining a bearing, sprocket or pulley against axial movement. Substituting a plain washer for a collar loses the set-screw seat and the H8 fit; substituting a collar for a washer buys thickness you do not need and a bore that may not clear your bolt. If your drawing says Shoulderring, setting ring or Axialring, that is this part.

What should an RFQ for DIN 703 collars state?

Bore d1 from the ladder (24-120; intermediate shaft sizes are not tabulated and are quotation items), material class (steel or stainless A2/A4 — the source prints nothing else), whether the matched DIN 914 set screw is required per the source pairing (e.g. d1 56 → M12x20), quantity per size — and, if your drawing leans on the legend/d3 mismatch flagged above, the note that the set-screw pairing should be confirmed against the standard document. Special faces (hardened, ground), sizes past the ladder, or non-ferrous material (source prints "-") are confirmed at quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 703 Collars, Heavy Series (d1 24 – 120) inquiry

  • ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
  • ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
  • ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
  • ✓ Describe the bearing surface or locking function, quantity per size and destination.
  • ✓ Factory-direct pricing for your DIN 703 Collars, Heavy Series (d1 24 – 120)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.