DIN 462 Internal Tab Washers
DIN 462 internal tab washers, Φ6 to Φ200 — the lock washer whose internal tongue engages a shaft keyway while its tabs bend against the nut — with the full collected 49-size table: bore, outside diameter, thickness, tab dimensions and tab length.
Last updated: 2026-11
Specifications
DIN 462 is the internal-tab lock washer for retaining nuts on shafts: its inner tongue sits in a keyway cut in the shaft and stops the washer rotating, while the outer tabs are bent up against the nut's flats after assembly — a positive mechanical lock that no thread friction provides. Machinists use it on bearing locknuts, gear-retaining nuts and any adjusted component that must not drift, because the lock survives disassembly cycles: bend the tabs back, remove the nut, refit, bend again. The collected table runs Φ6 to Φ200 — 49 sizes, the full standard span — with the bore d 1 (min = nominal size (H11) / max), outside diameter d 2 (max = nominal size (h11) / min), washer thickness s, tab thickness f (Nominal Size (c11) / max / min), tab height g (min = nominal size (H11) / max), and tab length h. Materials and finishes are not printed by the collected specification and stay per RFQ. The counterpart whose tongue sits in a housing notch and whose tabs face outward is DIN 463 on this site.
| Standard | DIN 462 — lock washers, internal tab (for shaft keyway engagement) |
|---|---|
| Series | Shaft diameters Φ6 – Φ200 (49 sizes tabulated) |
| Tabulated geometry | Per size: bore d 1 (min=nominal size(H11)/ max), outside diameter d 2 (max=nominal size(h11)/ min), thickness s, tab thickness f (Nominal Size(c11)/ max / min), tab height g (min=nominal size(H11)/ max), tab length h |
| Function | Internal tongue in the shaft keyway locks the washer; outer tabs bent against the nut lock the nut |
| Family note | External-tab counterpart DIN 463; the pair share the size ladder and differ in tongue placement |
| Materials / strength | Not tabulated by the collected specification — per RFQ (spring steel grade per drawing callout) |
| Nominal Diameter | d 1 — min=nominal size(H11) | d 1 — max | d 2 — max=nominal size(h11) | d 2 — min | s | f — Nominal Size(c11) | f — max | f — min | g — min=nominal size(H11) | g — max | h |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Φ6 | 6 | 6.075 | 16 | 15.89 | 0.8 | 3 | 2.94 | 2.88 | 3.9 | 3.975 | 2.5 |
| Φ8 | 8 | 8.09 | 20 | 19.87 | 0.8 | 3 | 2.94 | 2.88 | 5.9 | 5.975 | 2.5 |
| Φ10 | 10 | 10.09 | 25 | 24.87 | 0.8 | 4 | 3.93 | 3.855 | 7.4 | 7.49 | 3 |
| Φ12 | 12 | 12.11 | 28 | 27.87 | 0.8 | 5 | 4.93 | 4.855 | 9.3 | 9.39 | 3 |
| Φ14 | 14 | 14.11 | 30 | 29.87 | 0.8 | 5 | 4.93 | 4.855 | 11.4 | 11.51 | 3 |
| Φ16 | 16 | 16.11 | 32 | 31.84 | 1 | 5 | 4.93 | 4.855 | 13.5 | 13.61 | 3 |
| Φ18 | 18 | 18.11 | 34 | 33.84 | 1 | 6 | 5.93 | 5.855 | 15.4 | 15.51 | 4 |
| Φ20 | 20 | 20.13 | 36 | 35.84 | 1 | 6 | 5.93 | 5.855 | 17.5 | 17.61 | 4 |
| Φ22 | 22 | 22.13 | 40 | 39.84 | 1 | 6 | 5.93 | 5.855 | 19.5 | 19.63 | 4 |
| Φ24 | 24 | 24.13 | 42 | 41.84 | 1 | 6 | 5.93 | 5.855 | 21.6 | 21.73 | 4 |
| Φ26 | 26 | 26.13 | 45 | 44.84 | 1 | 7 | 6.92 | 6.83 | 23.5 | 23.63 | 5 |
| Φ28 | 28 | 28.13 | 50 | 49.84 | 1 | 7 | 6.92 | 6.83 | 25.5 | 25.63 | 5 |
| Φ30 | 30 | 30.13 | 50 | 49.84 | 1.2 | 7 | 6.92 | 6.83 | 27.5 | 27.63 | 5 |
| Φ32 | 32 | 32.16 | 52 | 51.81 | 1.2 | 7 | 6.92 | 6.83 | 29.6 | 29.73 | 5 |
| Φ35 | 35 | 35.16 | 55 | 54.81 | 1.2 | 7 | 6.92 | 6.83 | 32.6 | 32.76 | 5 |
| Φ38 | 38 | 38.16 | 58 | 57.81 | 1.2 | 8 | 7.92 | 7.83 | 35.3 | 35.46 | 5 |
| Φ40 | 40 | 40.16 | 62 | 61.81 | 1.2 | 8 | 7.92 | 7.83 | 37.3 | 37.46 | 5 |
| Φ42 | 42 | 42.16 | 62 | 61.81 | 1.2 | 8 | 7.92 | 7.83 | 39.3 | 39.46 | 5 |
| Φ45 | 45 | 45.16 | 68 | 67.81 | 1.2 | 8 | 7.92 | 7.83 | 42.4 | 42.56 | 5 |
| Φ48 | 48 | 48.16 | 75 | 74.81 | 1.2 | 8 | 7.92 | 7.83 | 45.4 | 45.56 | 5 |
| Φ50 | 50 | 50.16 | 75 | 74.81 | 1.2 | 8 | 7.92 | 7.83 | 47.4 | 47.56 | 5 |
| Φ52 | 52 | 52.19 | 80 | 79.81 | 1.2 | 10 | 9.92 | 9.83 | 49.3 | 49.46 | 6 |
| Φ55 | 55 | 55.19 | 80 | 79.81 | 1.2 | 10 | 9.92 | 9.83 | 52.3 | 52.49 | 6 |
| Φ58 | 58 | 58.19 | 90 | 89.78 | 1.5 | 10 | 9.92 | 9.83 | 55.3 | 55.49 | 6 |
| Φ60 | 60 | 60.19 | 90 | 89.78 | 1.5 | 10 | 9.92 | 9.83 | 57.3 | 57.49 | 6 |
| Φ62 | 62 | 62.19 | 95 | 94.78 | 1.5 | 10 | 9.92 | 9.83 | 59.3 | 59.49 | 6 |
| Φ65 | 65 | 65.19 | 95 | 94.78 | 1.5 | 10 | 9.92 | 9.83 | 62.4 | 62.59 | 6 |
| Φ68 | 68 | 68.19 | 100 | 99.78 | 1.5 | 10 | 9.92 | 9.83 | 65.4 | 65.59 | 6 |
| Φ70 | 70 | 70.19 | 100 | 99.78 | 1.5 | 10 | 9.92 | 9.83 | 67.4 | 67.59 | 6 |
| Φ72 | 72 | 72.19 | 110 | 109.78 | 1.5 | 10 | 9.92 | 9.83 | 68.9 | 69.09 | 7 |
| Φ75 | 75 | 75.19 | 110 | 109.78 | 1.5 | 10 | 9.92 | 9.83 | 71.9 | 72.09 | 7 |
| Φ80 | 80 | 80.19 | 115 | 114.78 | 1.5 | 10 | 9.92 | 9.83 | 76.9 | 77.09 | 7 |
| Φ85 | 85 | 85.22 | 120 | 119.78 | 1.5 | 10 | 9.92 | 9.83 | 81.9 | 82.12 | 7 |
| Φ90 | 90 | 90.22 | 130 | 129.75 | 1.5 | 10 | 9.92 | 9.83 | 86.9 | 87.12 | 7 |
| Φ95 | 95 | 95.22 | 135 | 134.75 | 1.5 | 12 | 11.905 | 11.795 | 91.8 | 92.02 | 8 |
| Φ100 | 100 | 100.22 | 145 | 144.75 | 1.5 | 12 | 11.905 | 11.795 | 96.9 | 97.12 | 8 |
| Φ105 | 105 | 105.22 | 155 | 154.75 | 1.5 | 12 | 11.905 | 11.795 | 102 | 102.22 | 8 |
| Φ110 | 110 | 110.22 | 155 | 154.75 | 1.5 | 12 | 11.905 | 11.795 | 107 | 107.22 | 8 |
| Φ115 | 115 | 115.22 | 165 | 164.75 | 1.5 | 12 | 11.905 | 11.795 | 112 | 112.22 | 8 |
| Φ120 | 120 | 120.22 | 165 | 164.75 | 1.5 | 12 | 11.905 | 11.795 | 117 | 117.22 | 8 |
| Φ125 | 125 | 125.25 | 180 | 179.75 | 1.5 | 12 | 11.905 | 11.795 | 122 | 122.25 | 8 |
| Φ130 | 130 | 130.25 | 180 | 179.75 | 1.5 | 12 | 11.905 | 11.795 | 127 | 127.25 | 8 |
| Φ140 | 140 | 140.25 | 195 | 194.71 | 1.5 | 12 | 11.905 | 11.795 | 137 | 137.25 | 8 |
| Φ150 | 150 | 150.25 | 205 | 204.71 | 1.5 | 12 | 11.905 | 11.795 | 147 | 147.25 | 8 |
| Φ160 | 160 | 160.25 | 220 | 219.71 | 1.5 | 12 | 11.905 | 11.795 | 157 | 157.25 | 10 |
| Φ170 | 170 | 170.25 | 230 | 229.71 | 1.5 | 12 | 11.905 | 11.795 | 167 | 167.25 | 10 |
| Φ180 | 180 | 180.25 | 245 | 244.71 | 1.5 | 12 | 11.905 | 11.795 | 177 | 177.25 | 10 |
| Φ190 | 190 | 190.29 | 260 | 259.68 | 1.5 | 12 | 11.905 | 11.795 | 187 | 187.29 | 10 |
| Φ200 | 200 | 200.29 | 270 | 269.68 | 1.5 | 12 | 11.905 | 11.795 | 197 | 197.29 | 10 |
Materials
- Material and finish specified per RFQ — the collected specification table covers geometry only
Ordering & documentation
Documents
Shipments of DIN 462 Internal Tab Washers are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 462 Internal Tab Washers orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 462 Internal Tab Washers), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 462 Internal Tab Washers: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 462 internal tab washers is 10,000 pieces (applies to the standard sizes and finishes for din 462 internal tab washers; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 462 internal tab washers run 3–7 days. Quantities or variants of din 462 internal tab washers outside the standard range are confirmed at quotation.
Storage & shipping
DIN 462 Internal Tab Washers are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 462 internal tab washers dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
How does a tab washer lock the nut, and can it be reused?
Mechanically, not by friction. After the nut is torqued, the washer's free tabs are bent up against one of the nut's flats; the internal tongue seated in the shaft keyway keeps the washer from spinning, so the nut cannot back off unless the tab is bent back first. That is also why tab washers are reusable in a way nylon-insert locknuts are not: bend the tab clear, remove and refit the nut, and bend a fresh section of tab against it. The limits are practical — the tab work-hardens after several bends, and the shaft must carry a keyway wide enough for the tongue, which the tabulated g dimension sizes.
What is the MOQ and lead time for this washer type?
The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Common sizes are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 462 Internal Tab Washers inquiry
- ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
- ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
- ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
- ✓ Describe the bearing surface or locking function, quantity per size and destination.
- ✓ Factory-direct pricing for your DIN 462 Internal Tab Washers
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support