ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in

ASME B18.31.2 continuous thread stud dimensions — thread size, TPI, and the source's per-size table from 1/4 through 4 in UNC, with the designation convention and length-increment rules the source prints, transcribed row-for-row.

Last updated: 2026-11

Request a Quote

ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in in an industrial setting
Illustrative image redrawn from real ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in product references — not a photograph of stocked items.

Specifications

A continuous thread stud is a bar threaded over its full usable length — no wrench-flat, no head, no unthreaded grip — designed to thread into a tapped hole at one end and carry a nut (or two, or a nut plus turnaround) at the other. It is the hardware of flanged joints, engine heads, pressure equipment and anywhere the stud is screwed into a body once and the load-bearing end assembled and disassembled repeatedly: the tapped-hole thread (the more expensive one to re-cut) stays virgin while wear lands on the replaceable nut end. ASME B18.31.2 is the governing inch standard, and the collected chart tabulates 1/4 through 4 in with thread designation and TPI per row (13 rows; note the flagged quirk carried below — the source prints "..." in the 8-UN column at the 1/4 – 1 in sizes, reproduced as printed). The designation convention is the practical ordering language: studs are specified by diameter, thread series and length — and per the source's example, thread ends are chamfered and the length increments follow the source's rule (note that close-length practices differ by purchaser spec). Grade, material, coating and machined-from-bar vs rolled-thread process are not tabulated by the collected chart — per RFQ; B7/B16 pressure-vessel grades pair with ASTM/ASME material specs on the drawing.

Standard ASME B18.31.2 — continuous thread studs, inch series (threaded over full usable length; no head, no wrench flats)
Size range 1/4 – 4 in, 13 printed rows; UNC coarse TPI ladder (20 down to 4) with 8-UN constant-pitch column as printed (see table footnote at 1/4 – 1 in)
Designation Diameter x thread x length (source's designation example printed on the chart); chamfered thread ends per source
Length increments Length-increment rule as printed by the source note — state exact length and increment practice at RFQ
Grade / material / coating Not tabulated by the collected chart — per RFQ (pressure-vessel service typically B7/B16 grades to the material spec on the drawing; rolled vs cut thread is a process RFQ line)
ASME B18.31.2 continuous thread studs (inch series) — thread ladders and minimum thread runoutAll dimensions in inches. D = stud diameter (fractional and decimal); TPI per series (UNC, UNF, 8UN). Min./Max. columns are the permissible length of thread runout (checked thread projection past the nut) per series; "—" marks series the source does not tabulate at that diameter (small sizes have no 8UN option). Overall length is in 1/4 in increments through 10 in; above 10 in, whole-inch and 1/2 in increments (source note).
D (fractional)D (decimal)UNC TPIUNF TPI8UN TPIUNC Runout (min)UNC Runout (max)UNF Runout (min)UNF Runout (max)8UN Runout (min)8UN Runout (max)
1/40.25002028-0.0500.1000.0360.071--
5/160.31251824-0.0560.1110.0420.083--
3/80.37501624-0.0630.1250.0420.083--
7/160.43751420-0.0720.1430.0500.100--
1/20.50001320-0.0770.1540.0500.100--
5/80.62501118-0.0910.1820.0560.111--
3/40.75001016-0.1000.2000.0630.125--
7/80.8750914-0.1110.2220.0720.143--
11.0000812-0.1250.2500.0840.167--
1 1/81.125071280.1430.2860.0840.1670.1250.250
1 1/41.250071280.1430.2860.0840.1670.1250.250
1 3/81.375061280.1670.3330.0840.1670.1250.250
1 1/21.500061280.1670.3330.0840.1670.1250.250
  • Row 1 (1/4): The source prints "..." in the 8UN TPI and 8UN runout columns for 1/4–1 in — the 8UN series simply is not offered at those diameters; shown here as "—".

Materials

  • Stud grade and material are drawing-level decisions (B7/B16 for pressure equipment, machine grades elsewhere); coating sequence interacts with tapped-hole fit — specify at RFQ

Ordering & documentation

Documents

Shipments of ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for asme b18.31.2 continuous thread studs — unc threads, 1/4 – 4 in is 1,000–10,000 pieces depending on size (applies to the standard sizes and finishes for asme b18.31.2 continuous thread studs — unc threads, 1/4 – 4 in; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for asme b18.31.2 continuous thread studs — unc threads, 1/4 – 4 in run 3–7 days. High-strength and custom parts for asme b18.31.2 continuous thread studs — unc threads, 1/4 – 4 in run 15–25 days. Quantities or variants of asme b18.31.2 continuous thread studs — unc threads, 1/4 – 4 in outside the standard range are confirmed at quotation.

Storage & shipping

ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store asme b18.31.2 continuous thread studs — unc threads, 1/4 – 4 in dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why choose a continuous thread stud over a bolt for a flanged or tapped-hole joint — and what must be specified beyond the chart?

The stud wins where the joint lives and dies by the nut end. Screwed into a tapped body once, the stud puts the repeated assembly cycle on the nut side: studs are cheap to replace and re-torque, the body's tapped thread — the part that ruins castings and machined bodies when it strips — never wears, and both ends can be torqued simultaneously for even gasket compression on flanges, which a headed bolt cannot do from one side. Continuous (full) thread maximizes engagement flexibility: the stud seats to any depth the hole offers, and the nut travels anywhere along the length — the reason it is the default for long through-flange stacks and insulation extensions. What the chart cannot order for you is the specification half: the collected table covers thread designation and TPI only, so grade/material (B7/B16 for pressure-vessel service with their own ASTM specs, machine grades elsewhere), thread class (2A as commercial, heavier classes per RFQ), coating (plating or galvanizing changes the fit into the tapped hole — see the internal 6H/2B allowance discussion), and rolled-vs-cut thread (rolled is stronger in fatigue, cut gives tighter runout) all arrive as RFQ lines. State stud diameter-series-length plus grade and finish together, and name the tapped-hole engagement depth on the drawing — a stud with too little engagement in a soft body is a pulled thread waiting to happen.

What is the MOQ and lead time for studs on this standard?

The minimum order quantity for ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in is 1,000–10,000 pieces depending on size. Stock items of ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in ship in 3–7 days; high-strength and custom parts in 15–25 days. Common stud sizes of ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in are widely stocked; confirm the exact schedule against quantity and length mix at quotation.

What is the MOQ and lead time for ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in?

Orders under this designation have a minimum order quantity of 1,000–10,000 pieces depending on size. Stock items ship in 3–7 days; high-strength and custom parts in 15–25 days. Final commercial terms are confirmed per quotation.

What should an RFQ for ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in state?

State the full designation (ASME B18.31.2), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in inquiry

  • ✓ Name the bolt standard and product form, then give nominal diameter, pitch, length and threaded length.
  • ✓ State the applicable property class or material grade, head style, and coating or finish.
  • ✓ Identify the mating nut/washer and the joint duty; include any specified preload, tightening method or friction condition.
  • ✓ Give quantity per size, destination and required material or inspection certificates.
  • ✓ Factory-direct pricing for your ASME B18.31.2 Continuous Thread Studs — UNC Threads, 1/4 – 4 in
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.