DIN 480 Square Head Bolts with Collar and Dog Point
DIN 480 square head bolts combining the DIN 478 collar with the DIN 479 dog point, M8 to M24 — machined seat plus pilot location in one bolt — with the full collected 8-column table: dog point d p and z, collar d c, head height k, radius r and across flats/corners.
Last updated: 2026-11
Specifications
DIN 480 is the full-featured member of the square head family: it carries the turned collar of DIN 478 under the head and the short dog point of DIN 479 on the shank end. One bolt therefore both locates (the dog engages the clearance hole, so nothing shifts and nothing spins while the nut is run) and seats on a machined face (the collar, so the clamp bears on a turned surface instead of a forging). That is the usual specification for clamp fixtures and machine-building joints where both conditions apply at once. The collected table covers M8 to M24 — 8 printed columns, with the source's across-flats variant labels "M16 SW 16", "M16 SW 17", "M20 SW 21" and "M20 SW 22" reproduced verbatim. Tabulated per size: the angle a, chamfer c, collar d c, dog point d p with projection z, head height k, radius r and across flats s / corners e with their limits. Materials, property classes and finishes are not printed by the collected specification and stay per RFQ.
| Standard | DIN 480 — square head bolts with collar and short dog point (located seat-and-pilot through bolt) |
|---|---|
| Series | M8 – M24 (8 tabulated columns; across-flats variants printed "SW 16"/"SW 17"/"SW 21"/"SW 22" by the source) |
| Tabulated geometry | Per size: pitch P, angle a (max), chamfer c (min/max), collar d c (max/min), dog point d p (max/min) and projection z (min/max), head height k (nominal/min/max), radius r (min), across flats s (max/min), across corners e (max/min) |
| Function | Dog point locates the joint and prevents rotation; collar provides the machined bearing face |
| Materials / strength | Not tabulated by the collected specification — per RFQ (property class per clamping load) |
| Size | P | a — max | c — min | c — max | d c — max=nominal size | d c — min | d p — max=nominal size | d p — min | k — Nominal Size | k — min | k — max | r — min | s — max=nominal size | s — min | z — min=nominal size | z — max |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M8 | 1.25 | 3.75 | 2.88 | 3.12 | 10 | 9.42 | 5.5 | 5.32 | 11 | 10.78 | 11.22 | 0.4 | 8 | 7.78 | 2 | 2.25 |
| M10 | 1.5 | 4.5 | 2.88 | 3.12 | 13 | 12.3 | 7 | 6.78 | 13 | 12.78 | 13.22 | 0.4 | 10 | 9.78 | 2.5 | 2.75 |
| M12 | 1.75 | 5.3 | 3.85 | 4.15 | 17 | 16.3 | 8.5 | 8.28 | 16 | 15.78 | 16.22 | 0.6 | 13 | 12.73 | 3 | 3.25 |
| M16 SW 16 | 2 | 6 | 3.85 | 4.15 | 21 | 20.16 | 12 | 11.73 | 20 | 19.74 | 20.26 | 0.6 | 16 | 15.73 | 4 | 4.3 |
| M16 SW 17 | 2 | 6 | 3.85 | 4.15 | 22 | 21.16 | 12 | 11.73 | 20 | 19.74 | 20.26 | 0.6 | 17 | 16.73 | 4 | 4.3 |
| M20 SW 21 | 2.5 | 7.5 | 4.85 | 5.15 | 27 | 26.16 | 15 | 14.73 | 25 | 24.74 | 25.26 | 0.8 | 21 | 20.67 | 5 | 5.3 |
| M20 SW 22 | 2.5 | 7.5 | 4.85 | 5.15 | 28 | 27.16 | 15 | 14.73 | 25 | 24.74 | 25.26 | 0.8 | 22 | 21.67 | 5 | 5.3 |
| M24 | 3 | 9 | 5.85 | 6.15 | 32 | 31 | 18 | 17.73 | 28 | 27.74 | 28.26 | 0.8 | 24 | 23.67 | 6 | 6.3 |
Materials
- Material and property class specified per RFQ — confirm against clamping load at quotation
Ordering & documentation
Documents
Shipments of DIN 480 Square Head Bolts with Collar and Dog Point are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 480 Square Head Bolts with Collar and Dog Point orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 480 Square Head Bolts with Collar and Dog Point), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 480 Square Head Bolts with Collar and Dog Point: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 480 square head bolts with collar and dog point is 1,000–10,000 pieces depending on size (applies to the standard sizes and finishes for din 480 square head bolts with collar and dog point; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 480 square head bolts with collar and dog point run 3–7 days. High-strength and custom parts for din 480 square head bolts with collar and dog point run 15–25 days. Quantities or variants of din 480 square head bolts with collar and dog point outside the standard range are confirmed at quotation.
Storage & shipping
DIN 480 Square Head Bolts with Collar and Dog Point are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 480 square head bolts with collar and dog point dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
DIN 479 or DIN 480 for a located square-head joint?
Look at the clamped face, not the bolt. If the head bears on rough steel, timber or a washer-tolerant surface, DIN 479 gives you the dog point and the forged head at the lighter part. If the head seats directly on a machined pad, fixture table or finished housing, DIN 480 adds the collar so the bearing face is turned rather than as-forged — the same reason DIN 478 exists for un-located joints. Both forms locate identically: match the dog point d p to the hole and keep the projection z under the second member's thickness, reading both from the collected table (mind the SW variant labels, which the source uses to split M16 and M20 across two across-flats values each — pick the column that matches your wrench set and hole tooling).
What is the MOQ and lead time for this bolt type?
The minimum order quantity for DIN 480 Square Head Bolts with Collar and Dog Point is 1,000–10,000 pieces depending on size. Stock items of DIN 480 Square Head Bolts with Collar and Dog Point ship in 3–7 days; high-strength and custom parts in 15–25 days. Common diameters of DIN 480 Square Head Bolts with Collar and Dog Point are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
What is the MOQ and lead time for DIN 480 Square Head Bolts with Collar and Dog Point?
Orders under this designation have a minimum order quantity of 1,000–10,000 pieces depending on size. Stock items ship in 3–7 days; high-strength and custom parts in 15–25 days. Final commercial terms are confirmed per quotation.
What should an RFQ for DIN 480 Square Head Bolts with Collar and Dog Point state?
State the full designation (DIN 480), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Related knowledge
- What Bolt Property Classes 8.8, 10.9 and 12.9 Encode — and When High Strength Stops Being the Right Choice
- Bolt Grade Selection: ISO 898-1 8.8/10.9/12.9 vs ASTM A307 and A325
- 8.8 vs 10.9 vs 12.9 Bolts: Strength, Hardness and Cost — What the Evidence Settles
- Calculating Bolt Preload and Clamp Force: Torque, Friction and Tightening Method
- How to Determine Tightening Torque and Choose a Tightening Method for a Bolted Joint
- Fastener Failure Modes: Which Fatigue, Creep and SCC Controls the Evidence Supports
- Hydrogen Embrittlement in High-Strength Bolts: Which Grades Need Controls, Which Coatings and Baking Schedules Are Acceptable, and What to Require Before the RFQ
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 480 Square Head Bolts with Collar and Dog Point inquiry
- ✓ Name the bolt standard and product form, then give nominal diameter, pitch, length and threaded length.
- ✓ State the applicable property class or material grade, head style, and coating or finish.
- ✓ Identify the mating nut/washer and the joint duty; include any specified preload, tightening method or friction condition.
- ✓ Give quantity per size, destination and required material or inspection certificates.
- ✓ Factory-direct pricing for your DIN 480 Square Head Bolts with Collar and Dog Point
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support