DIN 444 Eye Bolts (Eyelet Bolts)
Eye bolts per DIN 444 — an eye (loop/ring) at one end and a threaded shank at the other, for attaching rope or cable: thread into a pre-tapped hole or secure with a nut. M6–M24, lengths up to 150 mm, A2 and marine-grade A4 stainless.
Last updated: 2026-11
Specifications
DIN 444 is the eyelet bolt: a plain loop at one end, a standard thread at the other, and a job that is guidance rather than lifting — run rope, cable or chain through the loop and anchor the shank into a pre-tapped hole or a through-hole with a nut. The distinction that matters at specification time is against DIN 580 lifting eye bolts: DIN 444 eyes are for attachment points where a line is tied off, and the collected source carries the safety line explicitly — only shouldered eye bolts may be used to support angular loads. The collected stock program runs M6 to M24 with lengths up to 150 mm in A2 and marine-grade A4 stainless, which is the natural material line for a bolt whose typical service (railings, cables, marine rigging, guides) is wet or outdoor.
| Standard | DIN 444 — eye bolt (eyelet bolt): loop/ring at one end, threaded shank at the other |
|---|---|
| Function | Rope or cable attaches to the loop; shank threads into a pre-tapped hole or is secured with a nut |
| Angular-load rule | Only shouldered eye bolts may be used to support angular loads |
| Size range | M6 – M24, lengths up to 150 mm (stock program) |
| Materials (stock) | Stainless steel A2 and marine-grade A4 |
| Exemplar dimension (M10) | Width across flats (Type A): max 14 / min 13.3 mm; (Type B and C): max 12 / min 11.82 mm |
| Typical applications | Cable and rope tie-offs, railing and guide hardware, marine and outdoor attachment points |
Materials
- Stainless steel A2
- Stainless steel A4 (marine grade)
Collected DIN 444 eye bolt listings specify A2 and A4 stainless steel as the standard materials.
A4 is the marine-grade choice of the two; and because an eye bolt is a lifting fitting, confirm the intended load direction and duty with the supplier's certificate — the material covers corrosion, not the lifting derating.
Ordering & documentation
Documents
Shipments of DIN 444 Eye Bolts (Eyelet Bolts) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 444 Eye Bolts (Eyelet Bolts) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 444 Eye Bolts (Eyelet Bolts)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 444 Eye Bolts (Eyelet Bolts): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 444 eye bolts (eyelet bolts) is 1,000–10,000 pieces depending on size (applies to the standard sizes and finishes for din 444 eye bolts (eyelet bolts); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 444 eye bolts (eyelet bolts) run 3–7 days. High-strength and custom parts for din 444 eye bolts (eyelet bolts) run 15–25 days. Quantities or variants of din 444 eye bolts (eyelet bolts) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 444 Eye Bolts (Eyelet Bolts) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 444 eye bolts (eyelet bolts) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
DIN 444 or DIN 580 — which eye bolt for my application?
By load path. DIN 444 is the attachment eyelet: a line (rope, cable, light chain) ties off through the loop, and the bolt is stock stainless A2/A4 in M6–M24 — guidance hardware, not rated lifting. DIN 580 is the lifting eye bolt: a collared ring meant for rigging hooks and slings under vertical or angled load, in sizes to M80. If hardware or a person hangs from the ring, specify DIN 580 and treat it as rigging hardware; if a cable or rope anchors to it, DIN 444. And per the source caution, angular loads want a shouldered eye pattern — an unshouldered loop under an angled pull is the classic failure mode.
What is the MOQ and lead time for this bolt grade?
The minimum order quantity for DIN 444 Eye Bolts (Eyelet Bolts) is 1,000–10,000 pieces depending on size. Stock items of DIN 444 Eye Bolts (Eyelet Bolts) ship in 3–7 days; high-strength and custom parts in 15–25 days. Common diameters of DIN 444 Eye Bolts (Eyelet Bolts) are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
What should an RFQ for this bolt grade state?
For DIN 444 Eye Bolts (Eyelet Bolts), state the standard and grade (for example ISO 4017 Class 8.8 or ASTM F3125 Grade A325 Type 1), diameter and length, thread type (metric coarse or UNC/UNF), finish (plain, zinc, or hot-dip galvanized where the grade permits), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.
Related knowledge
- What Bolt Property Classes 8.8, 10.9 and 12.9 Encode — and When High Strength Stops Being the Right Choice
- Bolt Grade Selection: ISO 898-1 8.8/10.9/12.9 vs ASTM A307 and A325
- 8.8 vs 10.9 vs 12.9 Bolts: Strength, Hardness and Cost — What the Evidence Settles
- Calculating Bolt Preload and Clamp Force: Torque, Friction and Tightening Method
- How to Determine Tightening Torque and Choose a Tightening Method for a Bolted Joint
- Fastener Failure Modes: Which Fatigue, Creep and SCC Controls the Evidence Supports
- Hydrogen Embrittlement in High-Strength Bolts: Which Grades Need Controls, Which Coatings and Baking Schedules Are Acceptable, and What to Require Before the RFQ
- Bolt Head Types and Drive Styles: What the Evidence Can Settle Before You Specify
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 444 Eye Bolts (Eyelet Bolts) inquiry
- ✓ Name the bolt standard and product form, then give nominal diameter, pitch, length and threaded length.
- ✓ State the applicable property class or material grade, head style, and coating or finish.
- ✓ Identify the mating nut/washer and the joint duty; include any specified preload, tightening method or friction condition.
- ✓ Give quantity per size, destination and required material or inspection certificates.
- ✓ Factory-direct pricing for your DIN 444 Eye Bolts (Eyelet Bolts)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support