DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d)
Double-end metric studs to DIN 939 — the screwed-in end at approximately 1.25 × thread diameter, nut-end thread length tabulated by grip L through (M52), with the collected coarse/fine/very-fine pitch ladder M4 to (M52).
Last updated: 2026-11
Specifications
DIN 939 is the middle engagement of the double-end stud trio — screwed-in end ≈ 1.25 d (the collected b 1 row runs 5 mm at M4 to 65 mm at (M52)) — and is the most commonly drawn of the three for general machinery: enough engaged thread to hold in a standard tapping practice, without the stud standing off the housing. The collected ladder splits the pitch rows into coarse, fine and very fine variants per size, so a drawing calling an M12×1.25 or M12 fine stud resolves directly off the table. The nut end carries the grip-based engagement rows (L≤125 / 125<L≤200 / L>200), and the ladder runs to (M52). For the shorter and longer screwed-in ends see the DIN 938 and DIN 835 pages in this catalog. Material, property class and finish are not printed by the collected specification — per RFQ.
| Standard | DIN 939 — double-end studs, screwed-in end ≈ 1.25 d |
|---|---|
| Size range | M4 – (M52), parenthesised sizes non-preferred per the source notation |
| Screwed-in end | b 1: 5 – 65 mm across the ladder (≈ 1.25 × d) |
| Nut-end engagement | b 2 by grip: L≤125 / 125<L≤200 / L>200 rows per size (14 → 129 mm) |
| Thread variants | Coarse, fine and very fine pitch rows per size as tabulated by the source |
| Material / property class | Not tabulated by the collected specification — per RFQ |
| Attribute | M4 | M5 | M6 | (M7) |
|---|---|---|---|---|
| P — Pitch | 0.7 | 0.8 | 1 | 1 |
| P — Fine thread | / | / | / | / |
| P — Very fine thread | / | / | / | / |
| b 1 | 5 | 6.5 | 7.5 | 9 |
| b 2 — L≤125 | 14 | 16 | 18 | 20 |
| b 2 — 125<L≤200 | 20 | 22 | 24 | 26 |
| b 2 — L>200 | / | / | / | / |
| x 1 | 1.75 | 2 | 2.5 | 2.5 |
| x 2 | 0.9 | 1 | 1.25 | 1.25 |
- Row 7 (b 2 — L>200): The source prints "/" for the L>200 nut-end engagement on M4-(M7) — carried verbatim, not read across from larger sizes.
| Attribute | M8 | M10 | M12 |
|---|---|---|---|
| P — Pitch | 1.25 | 1.5 | 1.75 |
| P — Fine thread | 1 | 1.25 | 1.25 |
| P — Very fine thread | / | / | 1.5 |
| b 1 | 10 | 12 | 15 |
| b 2 — L≤125 | 22 | 26 | 30 |
| b 2 — 125<L≤200 | 28 | 32 | 36 |
| b 2 — L>200 | / | 45 | 49 |
| x 1 | 3.2 | 3.8 | 4.3 |
| x 2 | 1.6 | 1.9 | 2.2 |
| Attribute | (M14) | M16 | (M18) |
|---|---|---|---|
| P — Pitch | 2 | 2 | 2.5 |
| P — Fine thread | 1.5 | 1.5 | 1.5 |
| P — Very fine thread | / | / | / |
| b 1 | 18 | 20 | 22 |
| b 2 — L≤125 | 34 | 38 | 42 |
| b 2 — 125<L≤200 | 40 | 44 | 48 |
| b 2 — L>200 | 53 | 57 | 61 |
| x 1 | 5 | 5 | 6.3 |
| x 2 | 2.5 | 2.5 | 3.2 |
| Attribute | M20 | (M22) | M24 |
|---|---|---|---|
| P — Pitch | 2.5 | 2.5 | 3 |
| P — Fine thread | 1.5 | 1.5 | 2 |
| P — Very fine thread | / | / | / |
| b 1 | 25 | 28 | 30 |
| b 2 — L≤125 | 46 | 50 | 54 |
| b 2 — 125<L≤200 | 52 | 56 | 60 |
| b 2 — L>200 | 65 | 69 | 73 |
| x 1 | 6.3 | 6.3 | 7.5 |
| x 2 | 3.2 | 3.2 | 3.8 |
| Attribute | (M27) | M30 | (M33) |
|---|---|---|---|
| P — Pitch | 3 | 3.5 | 3.5 |
| P — Fine thread | 2 | 2 | 2 |
| P — Very fine thread | / | / | / |
| b 1 | 35 | 38 | 42 |
| b 2 — L≤125 | 60 | 66 | 72 |
| b 2 — 125<L≤200 | 66 | 72 | 78 |
| b 2 — L>200 | 79 | 85 | 91 |
| x 1 | 7.5 | 9 | 9 |
| x 2 | 3.8 | 4.5 | 4.5 |
| Attribute | M36 | (M39) | M42 |
|---|---|---|---|
| P — Pitch | 4 | 4 | 4.5 |
| P — Fine thread | 3 | 3 | 3 |
| P — Very fine thread | / | / | / |
| b 1 | 45 | 50 | 52 |
| b 2 — L≤125 | 78 | 84 | 90 |
| b 2 — 125<L≤200 | 84 | 90 | 96 |
| b 2 — L>200 | 97 | 103 | 109 |
| x 1 | 10 | 10 | 11 |
| x 2 | 5 | 5 | 5.5 |
| Attribute | (M45) | M48 | (M52) |
|---|---|---|---|
| P — Pitch | 4.5 | 5 | 5 |
| P — Fine thread | 3 | 3 | 3 |
| P — Very fine thread | / | / | / |
| b 1 | 58 | 60 | 65 |
| b 2 — L≤125 | 96 | 102 | 110 |
| b 2 — 125<L≤200 | 102 | 108 | 116 |
| b 2 — L>200 | 115 | 121 | 129 |
| x 1 | 11 | 12.5 | 12.5 |
| x 2 | 5.5 | 6.3 | 6.3 |
| Length (mm) | Weight kg/1000 pcs — M5 | Weight kg/1000 pcs — M6 | Weight kg/1000 pcs — M8 | Weight kg/1000 pcs — M10 | Weight kg/1000 pcs — M12 | Weight kg/1000 pcs — M16 | Weight kg/1000 pcs — M20 | Weight kg/1000 pcs — M24 | Weight kg/1000 pcs — M27 |
|---|---|---|---|---|---|---|---|---|---|
| 22 | 3.65 | ||||||||
| 25 | 4.11 | 5.85 | |||||||
| 28 | 4.57 | 6.52 | |||||||
| 30 | 4.88 | 6.96 | 13.1 | ||||||
| 35 | 5.65 | 8.07 | 15.1 | 24.2 | |||||
| 40 | 6.42 | 9.18 | 17 | 27.2 | 41 | ||||
| 45 | 7.19 | 10.2 | 19 | 30.3 | 45.4 | ||||
| 50 | 7.96 | 11.4 | 21 | 33.3 | 49.9 | 94.9 | |||
| 55 | 12.5 | 22.9 | 36.4 | 54.3 | 103 | ||||
| 60 | 13.6 | 24.9 | 39.5 | 58.8 | 111 | 180 | |||
| 65 | 26.9 | 42.6 | 63.2 | 119 | 192 | ||||
| 70 | 28.9 | 45.7 | 67.6 | 126 | 205 | 305 | |||
| 75 | 30.8 | 48.8 | 72.1 | 134 | 217 | 323 | 430 | ||
| 80 | 32.8 | 51.8 | 76.5 | 142 | 229 | 341 | 452 | ||
| 85 | 54.9 | 81 | 150 | 241 | 358 | 475 | |||
| 90 | 58 | 85.4 | 158 | 254 | 376 | 497 | |||
| 95 | 61.1 | 89.8 | 166 | 266 | 394 | 520 | |||
| 100 | 64.2 | 94.3 | 174 | 279 | 412 | 542 | |||
| 110 | 103 | 190 | 303 | 447 | 587 | ||||
| 120 | 112 | 205 | 328 | 483 | 632 | ||||
| 130 | 221 | 353 | 518 | 677 | |||||
| 140 | 237 | 377 | 554 | 722 | |||||
| 150 | 253 | 402 | 589 | 767 | |||||
| 160 | 269 | 427 | 625 | 812 | |||||
| 170 | 451 | 660 | 857 | ||||||
| 180 | 476 | 696 | 902 | ||||||
| 190 | 501 | 731 | 947 | ||||||
| 200 | 525 | 767 | 992 | ||||||
| 220 | 1082 | ||||||||
| 240 | 1172 |
- Row 1 (22): Column alignment note (batch-level, anchored here): the 9 weight columns align one-to-one to the source header sizes (M5, M6, M8, M10, M12, M16, M20, M24, M27); verified against the rendered grid (rowspan/colspan expanded) and the monotone per-size weight progressions, not inferred from the flattened markup alone. The first grid row is a lone "Length" section label, carried as the first-column semantics.
Materials
- Material and property class specified per RFQ — state the class and coating (carbon steel class, A2/A4 stainless, galvanized) at quotation
Ordering & documentation
Documents
Shipments of DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 939 double-end studs (screwed-in end ≈ 1.25 d) is 1,000–10,000 pieces depending on size (applies to the standard sizes and finishes for din 939 double-end studs (screwed-in end ≈ 1.25 d); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 939 double-end studs (screwed-in end ≈ 1.25 d) run 3–7 days. High-strength and custom parts for din 939 double-end studs (screwed-in end ≈ 1.25 d) run 15–25 days. Quantities or variants of din 939 double-end studs (screwed-in end ≈ 1.25 d) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 939 double-end studs (screwed-in end ≈ 1.25 d) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Why does the DIN 939 ladder use "/" where DIN 938 uses "-"?
Different presentation of the same absence: both marks are the source's way of printing "no tabulated value for this size/row" — the fine and very fine pitch rows and the long-grip (L>200) nut-end engagement on the small sizes. The figures are not missing from supply; they are simply not tabulated by the collected specification for those sizes, so quote the exact size-and-pitch callout on the RFQ and the engagement is confirmed per drawing rather than read across from a neighbouring size.
What is the MOQ and lead time for DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d)?
Orders under this designation have a minimum order quantity of 1,000–10,000 pieces depending on size. Stock items ship in 3–7 days; high-strength and custom parts in 15–25 days. Final commercial terms are confirmed per quotation.
What should an RFQ for DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d) state?
State the full designation (DIN 939), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Related knowledge
- What Bolt Property Classes 8.8, 10.9 and 12.9 Encode — and When High Strength Stops Being the Right Choice
- Bolt Grade Selection: ISO 898-1 8.8/10.9/12.9 vs ASTM A307 and A325
- 8.8 vs 10.9 vs 12.9 Bolts: Strength, Hardness and Cost — What the Evidence Settles
- Calculating Bolt Preload and Clamp Force: Torque, Friction and Tightening Method
- How to Determine Tightening Torque and Choose a Tightening Method for a Bolted Joint
- Fastener Failure Modes: Which Fatigue, Creep and SCC Controls the Evidence Supports
- Hydrogen Embrittlement in High-Strength Bolts: Which Grades Need Controls, Which Coatings and Baking Schedules Are Acceptable, and What to Require Before the RFQ
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d) inquiry
- ✓ Name the bolt standard and product form, then give nominal diameter, pitch, length and threaded length.
- ✓ State the applicable property class or material grade, head style, and coating or finish.
- ✓ Identify the mating nut/washer and the joint duty; include any specified preload, tightening method or friction condition.
- ✓ Give quantity per size, destination and required material or inspection certificates.
- ✓ Factory-direct pricing for your DIN 939 Double-End Studs (Screwed-In End ≈ 1.25 d)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support