DIN 479 Square Head Bolts with Short Dog Point

DIN 479 square head bolts with short dog point, M5 to M24 — the square head with a pilot dog point that locates the bolt in a reamed or drilled hole — with the full collected 10-size table: dog point d p and projection z, head geometry k/k 1, across flats and corners and the angle a.

Last updated: 2026-11

Request a Quote

DIN 479 Square Head Bolts with Short Dog Point in an industrial setting
Illustrative image redrawn from real DIN 479 Square Head Bolts with Short Dog Point product references — not a photograph of stocked items.

Specifications

DIN 479 pairs the square head with a short dog point: a reduced-diameter cylindrical pilot (d p) projecting a short length (z) beyond the shank. The dog drops into a corresponding hole or slot, so the bolt locates before the nut takes up — the clamp cannot walk, and the bolt cannot spin while the nut is run, which is the whole point on through-bolted joints where the shank is not threaded into the part. Between the dog and the head the source tabulates the chamfer/angle a, head height k with its k 1 under-head reference, across flats s and corners e, and the radius r. The collected table covers M5 to M24 — 10 printed columns, with across-flats variants labelled by the source as "M16 SW16", "M20 SW21" and "M20 SW22" (reproduced verbatim). Materials, property classes and finishes are not printed by the collected specification and stay per RFQ.

Standard DIN 479 — square head bolts with short dog point (pilot-located through bolts)
Series M5 – M24 (10 tabulated columns; across-flats variants printed "SW16"/"SW21"/"SW22" by the source)
Tabulated geometry Per size: pitch P, angle/chamfer a (max), dog point d p (max/min) and projection z (min/max), across corners e (max/min), head height k (nominal/max/min), k 1 (min), radius r (min), across flats s (max/min)
Function Dog point engages the clearance hole or slot so the bolt locates and holds while the nut is torqued
Materials / strength Not tabulated by the collected specification — per RFQ (property class per clamping load)
DIN 479 square head bolts with short dog point - per-size dimensions (M5 - M24, three source column groups)All dimensions in millimeters. Attribute labels follow the source: P = thread pitch; a = angle/chamfer (max); d p = dog point diameter; e = width across corners; k = head height (nominal / max / min); k 1 = head-related reference height (min); r = radius (min); s = width across flats; z = dog point projection (min=nominal size / max). SW labels on the size column (SW16, SW21, SW22) are the source's across-flats variant markers, reproduced verbatim. Rows keep the source's min/max order per attribute. Lengths, materials, property classes and finishes are not tabulated by the collected specification.
SizePa — maxd p — max=nominal sized p — mine — max=nominal sizee — mink — Nominal Sizek — maxk — mink 1 — minr — mins — max=nominal sizes — minz — min=nominal sizez — max
M50.82.43.53.326.55.9255.154.853.40.254.821.251.5
M61343.8287.4266.155.854.10.2565.821.51.75
M81.2545.55.32109.4288.187.825.50.487.7822.25
M101.54.576.781312.31010.189.826.90.4109.782.52.75
M121.755.38.58.281716.31212.2111.798.30.61312.7333.25
M16 SW16261211.732120.161616.2115.7911.10.61615.7344.3
M16 (s 17)261211.732221.161616.2115.7911.10.61716.7344.3
M20 SW212.57.51514.732726.162020.2619.7413.80.82120.6755.3
M20 SW222.57.51514.732827.162020.2619.7413.80.82221.6755.3
M24391817.7332312222.2621.7415.20.82423.6766.3

Materials

  • Material and property class specified per RFQ — confirm against clamping load at quotation

Ordering & documentation

Documents

Shipments of DIN 479 Square Head Bolts with Short Dog Point are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 479 Square Head Bolts with Short Dog Point orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 479 Square Head Bolts with Short Dog Point), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 479 Square Head Bolts with Short Dog Point: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 479 square head bolts with short dog point is 1,000–10,000 pieces depending on size (applies to the standard sizes and finishes for din 479 square head bolts with short dog point; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 479 square head bolts with short dog point run 3–7 days. High-strength and custom parts for din 479 square head bolts with short dog point run 15–25 days. Quantities or variants of din 479 square head bolts with short dog point outside the standard range are confirmed at quotation.

Storage & shipping

DIN 479 Square Head Bolts with Short Dog Point are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 479 square head bolts with short dog point dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why specify a dog point on a through bolt?

Because a plain shank through-bolt has to be held against rotation while the nut is torqued, usually with a second spanner on the square head in cramped space. The dog point removes that step: it seats in the hole (or a drilled recess) so the bolt cannot turn, and it centers the joint before clamping so parts do not shift as the nut loads. It also keeps the threads fully in the nut side — the reduced point cannot cut or jam at the hole mouth. Size the dog from the table: d p must be a running fit in your hole, and the projection z must be shorter than the second member is thick, or the dog bottoms before the head seats. Where the joint additionally needs a machined bearing face under the head, that is the DIN 480 form below; DIN 479 itself carries the standard forged square head.

What is the MOQ and lead time for this bolt type?

The minimum order quantity for DIN 479 Square Head Bolts with Short Dog Point is 1,000–10,000 pieces depending on size. Stock items of DIN 479 Square Head Bolts with Short Dog Point ship in 3–7 days; high-strength and custom parts in 15–25 days. Common diameters of DIN 479 Square Head Bolts with Short Dog Point are widely stocked; confirm the exact schedule against quantity and size mix at quotation.

What is the MOQ and lead time for DIN 479 Square Head Bolts with Short Dog Point?

Orders under this designation have a minimum order quantity of 1,000–10,000 pieces depending on size. Stock items ship in 3–7 days; high-strength and custom parts in 15–25 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN 479 Square Head Bolts with Short Dog Point state?

State the full designation (DIN 479), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 479 Square Head Bolts with Short Dog Point inquiry

  • ✓ Name the bolt standard and product form, then give nominal diameter, pitch, length and threaded length.
  • ✓ State the applicable property class or material grade, head style, and coating or finish.
  • ✓ Identify the mating nut/washer and the joint duty; include any specified preload, tightening method or friction condition.
  • ✓ Give quantity per size, destination and required material or inspection certificates.
  • ✓ Factory-direct pricing for your DIN 479 Square Head Bolts with Short Dog Point
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.