SAE J429 Grade 8 Bolts

SAE J429 Grade 8 — the high-strength inch-series alloy grade: 150 ksi minimum tensile, 130 ksi yield and 120 ksi proof load across the full 1/4″ through 1-1/2″ range at C33–C39, with no diameter drop. Six radial head lines.

Last updated: 2026-11

Request a Quote

SAE J429 Grade 8 Bolts in an industrial setting
Illustrative image redrawn from real SAE J429 Grade 8 Bolts product references — not a photograph of stocked items.

Specifications

Grade 8 is the top of the SAE system: a quenched-and-tempered medium-carbon alloy steel marked with six radial lines, held at 150 ksi minimum tensile across the entire 1/4″–1-1/2″ range — the collected specification is explicit that there is no diameter step, unlike Grades 2 and 5, because the alloy content (Cr, Ni, Mo or V) and the hardenability it buys keep the through-section property where a plain carbon grade loses it. The trade-offs are real and the specification states them: the higher hardness that carries 150 ksi also makes the bolt more notch-sensitive, and under cyclic or impact loading a Grade 5 bolt at the same installed tension can be the more fatigue-tolerant choice. Grade 8 costs roughly 25–40% more than Grade 5; for static high-load joints that buys more margin per bolt, and for cyclic ones it deserves a second look before it is specified. The ASTM counterpart is A354 Grade BD; the matched nut is J995 Grade 8 or A563 DH with F436 hardened washers.

Standard SAE J429 Grade 8 — mechanical and material requirements for externally threaded inch-series fasteners
Head marking 6 radial lines, plus the manufacturer symbol
Material Medium-carbon alloy steel (alloying from Cr, Ni, Mo or V), quenched and tempered to higher hardness than Grade 5
Min. tensile 150 ksi across the full range — 1/4″ through 1-1/2″, no diameter drop
Min. yield 130 ksi across the full range
Min. proof load 120 ksi across the full range
Hardness Rockwell C33–C39 (HRC)
Size range 1/4″ through 1-1/2″ — no mechanical step anywhere in the range
Typical pairing SAE J995 Grade 8 or ASTM A563 Grade DH nut; F436 hardened washer
ASTM counterpart Functionally equivalent to ASTM A354 Grade BD (high-strength alloy Q&T at 150 ksi)

Materials

  • Medium-carbon alloy steel (Cr/Ni/Mo/V alloying), quenched and tempered

Ordering & documentation

Documents

Shipments of SAE J429 Grade 8 Bolts are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for SAE J429 Grade 8 Bolts orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (SAE J429 Grade 8 Bolts), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for SAE J429 Grade 8 Bolts: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for sae j429 grade 8 bolts is 1,000–10,000 pieces depending on size (applies to the standard sizes and finishes for sae j429 grade 8 bolts; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for sae j429 grade 8 bolts run 3–7 days. High-strength and custom parts for sae j429 grade 8 bolts run 15–25 days. Quantities or variants of sae j429 grade 8 bolts outside the standard range are confirmed at quotation.

Storage & shipping

SAE J429 Grade 8 Bolts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store sae j429 grade 8 bolts dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Is Grade 8 always the upgrade from Grade 5?

For static loading, yes in margin: 150 ksi vs 120 ksi tensile means more clamping force or less weight for the same load, at roughly 25–40% higher cost. The collected comparison is explicit about the exception: under cyclic or impact loading the higher hardness makes Grade 8 more notch-sensitive, and it can be less fatigue-tolerant than a Grade 5 bolt at the same installed tension — the table lists "cyclic or impact loading; marginal lubrication" under when NOT to upgrade. Decide by load character, not by strength table alone, and keep the substitution decision with the drawing's engineer rather than upgrading at the counter.

What makes Grade 8 hold 150 ksi at 1-1/2″ when other grades step down?

Alloy content and quench-and-temper. Grade 2 loses strength above 3/4″ and Grade 5 above 1″ because thick plain-carbon sections do not through-harden; Grade 8's alloying (chromium, nickel, molybdenum or vanadium per the collected chemistry note) gives the hardenability to hit C33–C39 and 150 ksi tensile through the full 1/4″–1-1/2″ range. That is also why the matched hardware is non-negotiable: A563 Grade DH nuts and F436 hardened washers are what keep the joint failing in the bolt, not in a softer nut or a washer that dishes under preload.

What is the MOQ and lead time for this bolt grade?

The minimum order quantity for SAE J429 Grade 8 Bolts is 1,000–10,000 pieces depending on size. Stock items of SAE J429 Grade 8 Bolts ship in 3–7 days; high-strength and custom parts in 15–25 days. Common diameters of SAE J429 Grade 8 Bolts are widely stocked; confirm the exact schedule against quantity and size mix at quotation.

What should an RFQ for this bolt grade state?

For SAE J429 Grade 8 Bolts, state the standard and grade (for example ISO 4017 Class 8.8 or ASTM F3125 Grade A325 Type 1), diameter and length, thread type (metric coarse or UNC/UNF), finish (plain, zinc, or hot-dip galvanized where the grade permits), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your SAE J429 Grade 8 Bolts inquiry

  • ✓ Name the bolt standard and product form, then give nominal diameter, pitch, length and threaded length.
  • ✓ State the applicable property class or material grade, head style, and coating or finish.
  • ✓ Identify the mating nut/washer and the joint duty; include any specified preload, tightening method or friction condition.
  • ✓ Give quantity per size, destination and required material or inspection certificates.
  • ✓ Factory-direct pricing for your SAE J429 Grade 8 Bolts
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.