ASME B18.2.2 Square Nuts (Inch Series)
ASME B18.2.2 square nuts, inch series 1/4 – 1 1/2 in — the four-flat pattern paired with carriage bolts and square-head hardware, with the collected per-size table: width across flats and corners at basic/min/max and thickness at basic/min/max.
Last updated: 2026-11
Specifications
The square nut is the inch system's legacy pattern, and it survives because of what the four flats do that six cannot: a square nut resists turning to a flat in a square hole or chisel-cut slot, and it pairs with square-head bolts and carriage bolts where a wrench turns only to the next 90° face. The collected table runs 1/4 through 1 1/2 in and carries per size: width across flats F (basic/min/max), width across corners G (min/max) and thickness H (basic/min/max). The proportions differ from the hex pattern in ways that matter when substituting: across corners, a square nut reaches further (G = F × √2; the 1/2 in nut spans 0.788–0.812 across flats but 1.052–1.149 across corners, versus 0.840–0.866 corners for a 1/2 in hex nut), so on a tight corner-to-corner clearance the square pattern can foul where a hex fits. Thickness runs close to the hex nut's (1/2 in: 0.418–0.458 vs 0.427–0.448 hex). The F basic column reads as simple fractions — 7/16, 9/16, 5/8 — which is why square nuts still get cut into legacy wood and cast-iron work with period hardware. Property classes and finishes are not tabulated by the collected specification — per RFQ.
| Standard | ASME B18.2.2-2010 — square and hex nuts, inch series (square nut: four-flat pattern for square-head and carriage-bolt assemblies) |
|---|---|
| Size range | Nominal 1/4 – 1 1/2 in, thirteen sizes (1/4, 5/16, 3/8 … 1 1/2); one geometry row per size; no machine screw sizes below 1/4 in the collected table |
| Tabulated geometry | Per size: basic major dia. of thread, width across flats F (basic/min/max), width across corners G (min/max), thickness H (basic/min/max) — e.g. 1/2 in: F 13/16 basic (0.788–0.812), G 1.052–1.149, H 7/16 basic (0.418–0.458) |
| Proportions | Across corners G extends to F × √2 — further than a hex nut at the same thread; thickness H tracks the hex nut within a few thousandths across the ladder |
| Property classes / finishes | Not tabulated by the collected specification — per RFQ (state grade and finish at quotation) |
| Nominal Size | Basic Major Dia. of Thread | F — Across Flats (basic) | F (min) | F (max) | G — Across Corners (min) | G (max) | H — Thickness (basic) | H (min) | H (max) |
|---|---|---|---|---|---|---|---|---|---|
| 1/4 | 0.2500 | 7/16 | 0.425 | 0.438 | 0.554 | 0.619 | 7/32 | 0.203 | 0.235 |
| 5/16 | 0.3125 | 9/16 | 0.547 | 0.562 | 0.721 | 0.795 | 17/64 | 0.249 | 0.283 |
| 3/8 | 0.3750 | 5/8 | 0.606 | 0.625 | 0.802 | 0.884 | 21/64 | 0.310 | 0.346 |
| 7/16 | 0.4375 | 3/4 | 0.728 | 0.750 | 0.970 | 1.061 | 3/8 | 0.356 | 0.394 |
| 1/2 | 0.5000 | 13/16 | 0.788 | 0.812 | 1.052 | 1.149 | 7/16 | 0.418 | 0.458 |
| 5/8 | 0.6250 | 1 | 0.969 | 1.000 | 1.300 | 1.414 | 35/64 | 0.525 | 0.569 |
| 3/4 | 0.7500 | 1 1/8 | 1.088 | 1.125 | 1.464 | 1.591 | 21/32 | 0.632 | 0.680 |
| 7/8 | 0.8750 | 1 5/16 | 1.269 | 1.312 | 1.712 | 1.856 | 49/64 | 0.740 | 0.792 |
| 1 | 1.0000 | 1 1/2 | 1.450 | 1.500 | 1.961 | 2.121 | 7/8 | 0.847 | 0.903 |
| 1 1/8 | 1.1250 | 1 11/16 | 1.631 | 1.688 | 2.209 | 2.386 | 1 | 0.970 | 1.030 |
| 1 1/4 | 1.2500 | 1 7/8 | 1.812 | 1.875 | 2.458 | 2.652 | 1 3/32 | 1.062 | 1.126 |
| 1 3/8 | 1.3750 | 2 1/16 | 1.994 | 2.062 | 2.708 | 2.917 | 1 13/64 | 1.169 | 1.237 |
| 1 1/2 | 1.5000 | 2 1/4 | 2.175 | 2.250 | 2.956 | 3.182 | 1 5/16 | 1.276 | 1.348 |
Materials
- Material, property class and finish specified per RFQ — state the mating bolt (square head or carriage bolt) with the order so the wrenching and bearing pattern matches
Ordering & documentation
Documents
Shipments of ASME B18.2.2 Square Nuts (Inch Series) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ASME B18.2.2 Square Nuts (Inch Series) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ASME B18.2.2 Square Nuts (Inch Series)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for ASME B18.2.2 Square Nuts (Inch Series): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for asme b18.2.2 square nuts (inch series) is 10,000 pieces (applies to the standard sizes and finishes for asme b18.2.2 square nuts (inch series); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for asme b18.2.2 square nuts (inch series) run 3–7 days. Quantities or variants of asme b18.2.2 square nuts (inch series) outside the standard range are confirmed at quotation.
Storage & shipping
ASME B18.2.2 Square Nuts (Inch Series) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store asme b18.2.2 square nuts (inch series) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Can I swap a hex nut for a square nut at the same thread size?
The thread will mate, but two dimensions decide whether the swap works, and both are on the collected tables. Across corners is the first check: the square nut's corners reach F × √2 — the 1/2 in square nut spans 1.052–1.149 in corner to corner while the 1/2 in hex nut reaches only 0.840–0.866 in — so in a recess or against adjacent hardware the square pattern can foul where the hex fit. Across flats is the second: the wrench sizes differ (1/2 in square: 13/16 basic; 1/2 in hex: 3/4 basic), and a square nut cannot be turned past 90° per wrench reposition, which matters in tight access — the hex pattern offers six positions, the square four. Where the square nut is genuinely the right answer it wins for positive reasons: it cannot rotate in a square hole or chisel slot, it is the period-correct partner for square-head machine bolts, and its simple fractional F basics (7/16, 9/16, 5/8 …) make it the pattern legacy drawings specify. Beyond geometry, do not carry an assumption across the swap: the hex nut page's proof-load grades are not tabulated for the square pattern by the collected specification, so state the required grade explicitly at quotation.
What is the MOQ and lead time for this nut type?
The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Common sizes in this nut type are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
What is the MOQ and lead time for ASME B18.2.2 Square Nuts (Inch Series)?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for ASME B18.2.2 Square Nuts (Inch Series) state?
State the full designation (ASME B18.2.2), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ASME B18.2.2 Square Nuts (Inch Series) inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your ASME B18.2.2 Square Nuts (Inch Series)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support