ASTM A194 Grade 2HM Heavy Hex Nuts
ASTM A194 Grade 2HM heavy hex nuts — quenched and tempered carbon steel sharing the Grade 2/2H chemistry row (C 0.40% min, Mn 1.00% max), the hardness-controlled 2H variant used in sour-service (NACE) stud-bolt assemblies with A193 B7M studs. Mechanical rows are not tabulated in the collected sources and are not asserted.
Last updated: 2026-11
Specifications
Grade 2HM is the hardness-controlled member of the Grade 2 family: the same carbon-steel chemistry row the specification prints for 2 and 2H (carbon 0.40% minimum, manganese 1.00% maximum), quenched and tempered — the collected grade table titles it "Quenched & tempered carbon steel hvy hex nut" — with the service role set by its hardness control rather than a higher strength number. In stud-bolt practice it is the nut side of sour-service (NACE) assemblies: the collected pairing table puts A193 B7M studs with 2HM nuts where controlled hardness limits the risk of sulfide stress cracking. The collected sources for this batch tabulate chemistry for the 2/2H/2HM row but no hardness or proof-load rows specific to 2HM — those figures stay fail-closed here rather than being carried over from 2H, because 2HM's controlled-hardness condition is not the same condition as 2H. Request the mill certificate against the size and condition of record at quotation.
| Standard | ASTM A194 — Grade 2HM (heavy hex pattern) |
|---|---|
| Material | Carbon steel, quenched and tempered — hardness-controlled variant of the Grade 2 family |
| Chemistry (2 / 2H / 2HM row) | C 0.40% min, Mn 1.00% max, P 0.04% max, S 0.05% max, Si 0.40% max |
| Service pairing | A193 B7M studs + A194 2HM nuts — sour (NACE) service, controlled hardness |
| Hardness / proof load | Not tabulated in the collected sources for 2HM — the 2H rows do not carry over; confirm per mill certificate against the size and condition of record |
Materials
- Carbon steel (quenched and tempered, hardness-controlled)
2HM shares the 2H material family — quenched-and-tempered carbon steel with the same 0.40% minimum carbon row — but it is the controlled-hardness variant the pairing charts put with A193 B7M studs, charted for sour service (NACE) discipline.
State 2HM on the order rather than calling it a 2H equivalent: the two are not interchangeable in service, and the certificate you check against should show the controlled-hardness acceptance and lot-level test scope that the M suffix discipline implies.
Ordering & documentation
Documents
Shipments of ASTM A194 Grade 2HM Heavy Hex Nuts are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ASTM A194 Grade 2HM Heavy Hex Nuts orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ASTM A194 Grade 2HM Heavy Hex Nuts), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for ASTM A194 Grade 2HM Heavy Hex Nuts: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for astm a194 grade 2hm heavy hex nuts is 10,000 pieces (applies to the standard sizes and finishes for astm a194 grade 2hm heavy hex nuts; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for astm a194 grade 2hm heavy hex nuts run 3–7 days. Quantities or variants of astm a194 grade 2hm heavy hex nuts outside the standard range are confirmed at quotation.
Storage & shipping
ASTM A194 Grade 2HM Heavy Hex Nuts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store astm a194 grade 2hm heavy hex nuts dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Can I substitute a Grade 2H nut where the drawing calls 2HM?
Not on your own authority. 2HM carries the same base chemistry as 2H but is specified in a hardness-controlled condition for sour-service (NACE) assemblies — the control exists to limit sulfide stress cracking, and 2H's full-strength hardness band can sit above the ceiling the service allows. Where the specification of record says 2HM, order 2HM with a mill certificate showing the hardness result; substitution is the engineer's call, not the supplier's.
Why does this page not list hardness or proof-load numbers like the 2H page?
Because the collected sources for this batch print chemistry for the 2/2H/2HM row but no hardness or proof-load table rows specific to 2HM — its controlled-hardness condition is a different metallurgical condition from 2H, so the 2H figures are not transferable. Rather than borrow numbers across grades, this page states the gap: confirm hardness and proof load per the mill certificate and the specification of record at quotation.
What is the MOQ and lead time for this nut type?
The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Common diameters in this nut type are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
What should an RFQ for this nut type state?
State the standard designation (for example DIN 985 or DIN 6923), nominal thread size and pitch (metric coarse unless fine pitch is required), material and strength pairing with the mating bolt, finish (plain, zinc, or hot-dip galvanized where compatible), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ASTM A194 Grade 2HM Heavy Hex Nuts inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your ASTM A194 Grade 2HM Heavy Hex Nuts
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support