Hex Thick Nuts (Inch Series)

Hex thick nuts, inch series 1/4 – 1 1/2 nominal — the taller hex pattern between the standard hex nut and the heavy hex nut, with the collected per-size table: width across flats and corners and thickness at basic/max/min.

Last updated: 2026-11

Request a Quote

Hex Thick Nuts (Inch Series) in an industrial setting
Illustrative image redrawn from real Hex Thick Nuts (Inch Series) product references — not a photograph of stocked items.

Specifications

The hex thick nut occupies the gap the inch hex system leaves between its two common patterns: same width across flats as the standard hex nut, but a thickness closer to (and above) the standard's — the tabulated data shows 9/16 basic thickness at 1/2 nominal, against 7/16 for a standard hex nut, on the same 3/4 flats. More thread engagement in the same wrench size is the whole point: where a joint needs extra length of thread in the nut — thin-walled tapped holes, studs that cannot be lengthened, threaded rod terminations — the thick nut buys engagement without changing the wrench or the envelope across the flats. The tabulated ladder runs 1/4 through 1 1/2 nominal and carries per size: width across flats F (fractional basic with max/min decimals — 3/4 basic, 0.750–0.736 at 1/2), across corners G (max/min) and thickness H (fractional basic with max/min — 9/16 basic, 0.573–0.552 at 1/2; 1 1/2 basic, 1.526–1.474 at 1 1/2). Two cautions from the tabulated data itself: 5/8 and 1.0 nominal are absent, so those sizes are not established (see the table footnote), and no governing standard is named for the pattern — quote the size and thread and the standard will be confirmed at RFQ. Threads, property classes and finishes are not tabulated — per RFQ.

Pattern Hex thick nut, inch series — standard-hex width across flats with elevated thickness for extra thread engagement; governing standard not named in the tabulated data
Size range Nominal 1/4 – 1 1/2 in, ten distinct sizes in the tabulated ladder; 5/8 and 1.0 absent (not established in the tabulated data)
Tabulated geometry Per size: width across flats F (basic/max/min), across corners G (max/min), thickness H (basic/max/min) — e.g. 1/2: F 3/4 basic (0.750–0.736), G 0.866–0.840, H 9/16 basic (0.573–0.552)
Thickness position H basic sits between standard and heavy hex: 9/16 at 1/2 nominal (vs 7/16 standard, 9/16+ heavy envelope), rising to 1 1/2 at 1 1/2 nominal
Threads / classes / finishes Not tabulated by the collected specification — per RFQ (state thread series, grade and finish at quotation)
Hex thick nuts — wrenching and thickness, 1/4–1 1/2 nominal (inch)All dimensions in inches. The ladder is transposed from per-size listings, duplicate selections reproduced verbatim (see anomaly note). F and H print a fractional basic with max/min decimals; G prints max/min. Threads, property classes and finishes are not tabulated — per RFQ.
ProductNominal Dia. (d)Width Across Flats (F) BasicF MaxF MinWidth Across Corners (G) MaxG MinThickness (H) BasicH MaxH Min
Hex Thick Nut0.25007/160.4380.4280.5050.4889/320.2880.274
Hex Thick Nut0.31251/20.5000.4890.5770.55721/640.3360.320
Hex Thick Nut0.37509/160.5620.5510.6500.62813/320.4150.398
Hex Thick Nut0.437511/160.6880.6750.7940.76829/640.4630.444
Hex Thick Nut0.50003/40.7500.7360.8660.8409/160.5730.552
Hex Thick Nut0.50003/40.7500.7360.8660.8409/160.5730.552
Hex Thick Nut0.50003/40.7500.7360.8660.8409/160.5730.552
Hex Thick Nut0.75001 1/81.1251.0881.2991.24013/160.8270.798
Hex Thick Nut0.75001 1/81.1251.0881.2991.24013/160.8270.798
Hex Thick Nut0.87501 5/161.3121.2691.5161.44729/320.9220.890
Hex Thick Nut1.12501 11/161.6881.6311.9491.8591 5/321.1761.136
Hex Thick Nut1.12501 11/161.6881.6311.9491.8591 5/321.1761.136
Hex Thick Nut1.37502 1/162.0621.9942.3822.2731 3/81.3991.351
Hex Thick Nut1.50002 1/42.2502.1752.5982.4801 1/21.5261.474
  • Row 6 (Hex Thick Nut): The 0.5000 row appears three times, 0.7500 and 1.1250 twice each — all reproduced verbatim.
  • Row 8 (Hex Thick Nut): Sizes 5/8 and 1.0 are absent from the published ladder. Verify against the governing standard before quoting those sizes.

Materials

  • Material, property class and finish specified per RFQ — thick nuts are commonly quoted for stud terminations; state the stud material and thread engagement requirement with the order

Ordering & documentation

Documents

Shipments of Hex Thick Nuts (Inch Series) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Hex Thick Nuts (Inch Series) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (Hex Thick Nuts (Inch Series)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for Hex Thick Nuts (Inch Series): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for hex thick nuts (inch series) is 10,000 pieces (applies to the standard sizes and finishes for hex thick nuts (inch series); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for hex thick nuts (inch series) run 3–7 days. Quantities or variants of hex thick nuts (inch series) outside the standard range are confirmed at quotation.

Storage & shipping

Hex Thick Nuts (Inch Series) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store hex thick nuts (inch series) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

When do I specify a thick nut instead of a standard or heavy hex nut?

Decide on thread engagement first, wrench envelope second. The tabulated data shows the pattern's identity: at 1/2 nominal the thick nut keeps the standard hex nut's 3/4 basic flats (0.750–0.736) but carries 9/16 basic thickness (0.573–0.552) — about 29% more thread engagement than the standard's 7/16, in a nut your existing 3/4 wrench still fits. That is the case to specify one: a stud or threaded-rod termination where the nut must develop strength from engagement rather than from a longer stud, a tapped hole in thin material where every thread counts, or a re-assembly where the nut alone was the wearing part. It is not a heavy hex nut substitute: the heavy pattern grows the flats themselves (a 1/2 heavy hex nut takes a 7/8 wrench) for a larger bearing face, while the thick nut keeps the 3/4 face — so under a high-tension bolt where bearing stress on the joint face is the concern, the heavy pattern is the honest answer, and where engagement is the concern, the thick nut wins on envelope. One data caveat before quoting: 5/8 and 1.0 nominal are absent from the tabulated data, so those two sizes are not established — state them at RFQ and they will be confirmed against the governing standard rather than assumed from the table.

What is the MOQ and lead time for this nut type?

The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Common sizes in this nut type are widely stocked; confirm the exact schedule against quantity and size mix at quotation.

What is the MOQ and lead time for Hex Thick Nuts (Inch Series)?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for Hex Thick Nuts (Inch Series) state?

State the full designation (Hex Thick Nuts (Inch Series)), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Hex Thick Nuts (Inch Series) inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your Hex Thick Nuts (Inch Series)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.