DIN 937 Hex Thin Slotted Nuts (Chamfered)

Hex thin slotted nuts per DIN 937, chamfered — the low-profile counterpart to the DIN 935 castle nut, tabulated M6 through M52, for cotter-pin locking where height is limited and no crown is provided.

Last updated: 2026-11

Request a Quote

DIN 937 Hex Thin Slotted Nuts (Chamfered) in an industrial setting
Illustrative image redrawn from real DIN 937 Hex Thin Slotted Nuts (Chamfered) product references — not a photograph of stocked items.

Specifications

DIN 937 does the DIN 935 job in a thinner profile: a chamfered hex nut, roughly half the height, with the same radial slots in its top face for a cotter pin through the bolt cross-hole. Where the castle nut earns its extra height by seating a crown, the thin slotted nut wins in the many joints that cannot spend that height — linkage eyes, clevis ends, adjustment hardware — while still needing a lock that survives service without preload. The tradeoff is thread engagement: with less height, fewer threads carry the load, so DIN 937 belongs on joints sized with that in mind rather than as a drop-in replacement for a full-height nut. The collected table runs M6 to M52 with across-flats s 10–80 mm, height k max 6–27 mm, slot width n and per-size weights, all row-aligned for quoting. Assembly and locking behavior are identical to the castle nut: tighten, align slots with the bolt cross-hole, insert and bend the pin — the lock is positive and visually checkable, independent of how tight the nut ended up.

Standard DIN 937 — hex thin slotted nuts, chamfered (low-profile cotter-pin lock nut)
Size range M6 through M52 — width across flats s max (= nominal) 10–80 mm, height k max 6–27 mm
Slot geometry Slot width n tabulated min/max per size (top-face slots for the cotter pin)
Locking mechanism Positive: cotter pin through nut slot and bolt cross-hole — preload-independent and visually inspectable
Selection note Reduced height means reduced thread engagement — size the joint for it; use DIN 935 where full nut height is available
DIN 937 hex thin slotted nuts (chamfered) - per-size dimensions (M6 - M52)All dimensions in millimeters; weight per 1000 pieces. The source prints two fine-pitch series; fine-1 and fine-2 are tabulated separately here ("/" = column not tabulated for the size, "-" = not applicable).
Nominal threadPitch, coarse (mm)Pitch, fine-1 (mm)Pitch, fine-2 (mm)de max (mm)de min (mm)e min (mm)Height k max (mm)k min (mm)Slot width n min (mm)Slot width n max (mm)Width across flats s max (= nominal) (mm)s min (mm)w min (mm)w max (mm)Weight ≈ (kg / 1000 pcs)
M61--//11.0565.722.25109.783.23.52.5
(M7)1--//12.1276.6422.251110.733.743.4
M81.251-//14.3887.642.52.751312.734.24.55.4
M101.51.51.25//18.998.642.83.051716.734.7511.3
M121.751.51.251716.5720.1109.643.53.81918.675.7614.7
(M14)21.5-1918.4824.491110.573.53.82221.676.64717.9
M1621.5-2221.4826.751211.574.54.82423.676.64722.7
(M18)2.521.52524.329.561312.34.54.82726.167.64833.2
M202.521.52827.332.951312.34.54.83029.167.64841.1
(M22)2.521.53029.335.031514.35.55.832318.64949.8
M2432-343339.551514.35.55.836358.64967.8
(M27)32-383745.21716.35.55.8414010.5711103
M303.52-424150.851817.377.36464510.5711133
(M33)3.52-464555.372019.1677.36504912.5713173
M3643-504960.792019.1677.365553.812.5713215
(M39)43-5553.866.442221.1677.366058.812.5713269
M424.53-5856.872.022322.1699.366563.813.5714310
(M45)4.53-6260.876.952524.1699.367068.115.5716406
M4853-6563.882.62524.1699.367573.115.5716463
(M52)53-7068.888.252726.1699.368078.117.5718580

Materials

  • Material and strength grade specified per RFQ — the collected specification tables cover geometry and unit weights only

Ordering & documentation

Documents

Shipments of DIN 937 Hex Thin Slotted Nuts (Chamfered) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 937 Hex Thin Slotted Nuts (Chamfered) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 937 Hex Thin Slotted Nuts (Chamfered)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 937 Hex Thin Slotted Nuts (Chamfered): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 937 hex thin slotted nuts (chamfered) is 10,000 pieces (applies to the standard sizes and finishes for din 937 hex thin slotted nuts (chamfered); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 937 hex thin slotted nuts (chamfered) run 3–7 days. Quantities or variants of din 937 hex thin slotted nuts (chamfered) outside the standard range are confirmed at quotation.

Storage & shipping

DIN 937 Hex Thin Slotted Nuts (Chamfered) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 937 hex thin slotted nuts (chamfered) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

When does the thin DIN 937 make more sense than the DIN 935 castle nut?

When the joint needs the pin lock but cannot afford the crown height. Clevis and linkage ends, adjustable brackets, and hardware inside housings often have only the bare thread engagement available — a full castle nut would bottom out or leave too little thread in grip. DIN 937 gives the same positive, inspectable cotter-pin lock in roughly half the height. The cost is thread engagement, so the joint must be sized knowing fewer threads carry the load; where height is no constraint, the taller DIN 935 keeps more engagement and its crown adds pin guidance.

Does the thinner nut change how the lock is assembled?

No — the mechanism is identical. Tighten the nut, rotate it to bring a slot in line with the bolt cross-hole, run the cotter pin through and bend its legs. Both the slot and the pin are sized in the collected table per thread size, so take the pairing from the same row. Two practical notes from the low profile: there are fewer slots to align, so the final torque step should approach the hole position deliberately, and because thread engagement is shorter, verify the bolt cross-hole sits within the nut height rather than below it — a pin that misses the slot locks nothing.

What is the MOQ and lead time for this nut type?

The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Confirm the exact schedule against quantity and size mix at quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 937 Hex Thin Slotted Nuts (Chamfered) inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your DIN 937 Hex Thin Slotted Nuts (Chamfered)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.