DIN 1816 Round Nuts with Set-Pin Holes (Inside)
DIN 1816 round nuts with set-pin holes inside, M6×0,75 – M200×3 — the slotted-alternative bearing locknut locked by a set pin through drilled face holes, with the collected diameter/height/pin-hole ladder.
Last updated: 2026-11
Specifications
DIN 1816 is the round locknut whose locking feature is drilled face holes rather than the slots of the KM series: a cylindrical nut with a fine-pitch thread, a hardened set pin driven through holes drilled in the face (counter-bored "d4" holes in the collected ladder) rides against the bearing shoulder or shaft thread and is locked by that pin instead of a lockwasher tab. Compared with the KM/KMN locknuts in this catalog, the pin-locked face leaves the full circumference free of slot cut-outs — the nut runs truer at speed and presents no slot edges to windage or cleaning fluids, which is why the series runs to very large threads (the collected ladder tops out at M200×3, dk 270 mm). The collected table carries per thread the outside diameter dk (16 → 270 mm), the height k (5 → 20 mm), the pin-hole diameter d4 (2,5 → 10 mm) and count (4 → 8), plus the d1, t and h dimensions as lettered by the source. Read the ladder with one caution: where the source repeats a designation across two diameter variants (M24, M28) or carries one obvious mislabel (the "M20x1,5" row at dk 80), the rows are reproduced verbatim and flagged under the table — confirm the exact designation and outside diameter on the RFQ. Mounting: the nut is threaded on until it seats, then the pin is driven through the face hole into a matching dimple or slot in the shaft — the shaft or the mating lock element must provide that landing. Materials and hardness are not tabulated by the collected specification — per RFQ.
| Standard | DIN 1816 — round nuts with set-pin holes inside (pin-locked alternative to slotted KM locknuts) |
|---|---|
| Size range | M6×0,75 – M200×3, fine-pitch threads throughout; 49 rows in the collected ladder |
| Outside diameter | dk: 16 → 270 mm across the ladder |
| Height / pin holes | k: 5 → 20 mm; pin-hole diameter d4: 2,5 → 10 mm; 4 holes to M45, 6 from M45, 8 from M125 |
| Tolerance classes | dk h11, pin holes d4 H11, height k h14 (tolerance row as printed by the source) |
| Materials / hardness | Not tabulated by the collected specification — per RFQ (state shaft material and locking-pin arrangement at quotation) |
| Thread (d) | Outside Dia. (dk) | d1 | Pin Hole Dia. (d4) | Height (k) | t | h | Pin Holes | Weight kg/100 pcs (7,85 kg/dm³) |
|---|---|---|---|---|---|---|---|---|
| M6x0,75 | 16 | 12 | 2,5 | 5 | 4 | 0,5 | 4 | 0,595 |
| M8x1 | 20 | 16 | 2,5 | 5 | 4,5 | 0,5 | 4 | 0,95 |
| M10x1 | 25 | 20 | 3 | 6 | 4,5 | 0,5 | 4 | 1,81 |
| M12x1,5 | 28 | 23 | 3 | 6 | 5 | 0,5 | 4 | 2,23 |
| M14x1,5 | 30 | 25 | 4 | 7 | 5 | 0,5 | 4 | 2,88 |
| M16x1,5 | 32 | 27 | 4 | 7 | 6 | 0,5 | 4 | 3,12 |
| M18x1,5 | 34 | 28 | 4 | 8 | 6 | 0,5 | 4 | 3,92 |
| M20x1,5 | 36 | 30 | 4 | 8 | 6 | 0,5 | 4 | 4,25 |
| M22x1,5 | 40 | 34 | 4 | 9 | 6 | 0,5 | 4 | 6,05 |
| M24x1,5 | 42 | 36 | 4 | 9 | 6 | 0,5 | 4 | 6,45 |
| M24x1,5 | 45 | 38 | 5 | 10 | 6 | 0,5 | 4 | 8,1 |
| M28x1,5 | 50 | 43 | 5 | 10 | 7 | 0,5 | 4 | 10,3 |
| M28x1,5 | 50 | 43 | 5 | 10 | 7 | 0,5 | 4 | 9,55 |
| M30x1,5 | 52 | 45 | 5 | 11 | 7 | 0,5 | 4 | 11,1 |
| M32x1,5 | 55 | 48 | 5 | 11 | 7 | 0,5 | 4 | 12 |
| M35x1,5 | 58 | 50 | 5 | 11 | 8 | 0,5 | 4 | 12,7 |
| M38x1,5 | 62 | 54 | 6 | 12 | 8 | 0,5 | 4 | 16,2 |
| M40x1,5 | 62 | 54 | 6 | 12 | 8 | 0,5 | 4 | 15 |
| M42x1,5 | 68 | 60 | 6 | 12 | 8 | 0,5 | 4 | 18,5 |
| M45x1,5 | 75 | 67 | 6 | 13 | 10 | 0,5 | 6 | 25,6 |
| M48x1,5 | 75 | 67 | 6 | 13 | 10 | 0,5 | 6 | 24,1 |
| M20x1,5 | 80 | 70 | 6 | 13 | 10 | 0,5 | 6 | 28,6 |
| M52x1,5 | 80 | 70 | 6 | 13 | 10 | 0,5 | 6 | 26,1 |
| M58x1,5 | 90 | 80 | 6 | 13 | 10 | 0,5 | 6 | 37 |
| M60x1,5 | 90 | 80 | 6 | 13 | 10 | 0,5 | 6 | 35,1 |
| M62x1,5 | 95 | 85 | 8 | 14 | 12 | 0,5 | 6 | 42,3 |
| M65x1,5 | 95 | 85 | 8 | 14 | 12 | 0,5 | 6 | 39,2 |
| M68x1,5 | 100 | 90 | 8 | 14 | 12 | 0,5 | 6 | 44 |
| M70x1,5 | 100 | 90 | 8 | 14 | 12 | 0,5 | 6 | 41,5 |
| M72x1,5 | 110 | 100 | 8 | 14 | 12 | 0,5 | 6 | 57,4 |
| M75x1,5 | 110 | 100 | 8 | 14 | 12 | 0,5 | 6 | 53,6 |
| M80x2 | 115 | 105 | 8 | 16 | 12 | 1 | 6 | 57,5 |
| M85x2 | 120 | 110 | 8 | 16 | 12 | 1 | 6 | 68 |
| M90x2 | 130 | 120 | 8 | 16 | 12 | 1 | 6 | 84,3 |
| M95x2 | 135 | 120 | 8 | 16 | 12 | 1 | 6 | 87,5 |
| M100x2 | 145 | 130 | 8 | 16 | 12 | 1 | 6 | 106 |
| M105x2 | 155 | 140 | 8 | 16 | 12 | 1 | 6 | 125 |
| M110x2 | 155 | 140 | 8 | 16 | 12 | 1 | 6 | 114 |
| M115x2 | 165 | 150 | 10 | 18 | 15 | 1 | 6 | 149 |
| M120x2 | 165 | 150 | 10 | 18 | 15 | 1 | 6 | 136 |
| M125x2 | 180 | 165 | 10 | 18 | 15 | 1 | 8 | 178 |
| M130x3 | 180 | 165 | 10 | 18 | 15 | 1 | 8 | 167 |
| M140x3 | 195 | 180 | 10 | 18 | 15 | 1 | 8 | 200 |
| M150x3 | 205 | 190 | 10 | 18 | 15 | 1 | 8 | 212 |
| M160x3 | 220 | 205 | 10 | 20 | 15 | 1 | 8 | 277 |
| M170x3 | 230 | 210 | 10 | 20 | 15 | 1 | 8 | 291 |
| M180x3 | 245 | 225 | 10 | 20 | 15 | 1 | 8 | 336 |
| M190x3 | 260 | 240 | 10 | 20 | 18 | 1 | 8 | 381 |
| M200x3 | 270 | 250 | 10 | 20 | 18 | 1 | 8 | 442 |
- Row 11 (M24x1,5): The thread designation M24x1,5 appears on two consecutive rows (dk 42 / dk 45): the source serves the two diameter variants without labelling them. Reproduced verbatim; state the required outside diameter on the RFQ.
- Row 13 (M28x1,5): M28x1,5 appears twice with identical geometry but different weights (10,3 / 9,55 kg) — a source quirk reproduced verbatim. Verify before quoting.
- Row 22 (M20x1,5): The designation "M20x1,5" at dk 80 sits in the M50–M56 range of the ladder and is almost certainly a mislabelled thread designation in the source; the row is reproduced verbatim — verify the designation against DIN 1816 before ordering this size.
Materials
- Material specified per RFQ — bearing locknuts see the shaft environment; state the operating speed, temperature and whether the pin landing is a dimple or a keyway with the order
Ordering & documentation
Documents
Shipments of DIN 1816 Round Nuts with Set-Pin Holes (Inside) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 1816 Round Nuts with Set-Pin Holes (Inside) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 1816 Round Nuts with Set-Pin Holes (Inside)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 1816 Round Nuts with Set-Pin Holes (Inside): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 1816 round nuts with set-pin holes (inside) is 10,000 pieces (applies to the standard sizes and finishes for din 1816 round nuts with set-pin holes (inside); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 1816 round nuts with set-pin holes (inside) run 3–7 days. Quantities or variants of din 1816 round nuts with set-pin holes (inside) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 1816 Round Nuts with Set-Pin Holes (Inside) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 1816 round nuts with set-pin holes (inside) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
DIN 1816 or DIN 981 (KM) — how do I choose the locknut, and what does the pin need?
Both lock a bearing positioning nut against rotation; the locking interface differs. The KM/DIN 981 series in this catalog locks through an outer tab washer, with slots cut into the nut circumference; DIN 1816 locks through a set pin driven into face holes, so the circumference stays continuous. That continuity is the selection argument: at higher speeds, in washdown or grit-laden environments, or where the nut runs close to a seal, the slot-free face runs cleaner and truer. What the pin needs from the rest of the assembly is the landing: a dimple, flat or keyway in the shaft aligned with one of the face holes when the nut is at final torque — plan that feature into the shaft drawing, because the collected table fixes the pin geometry (d4 2,5 → 10 mm, four to eight holes by size) but not the landing. Read the collected ladder at the duplicate designations with care: M24 and M28 each appear on two diameter variants and one row is an obvious designation mislabel (flagged under the table) — quote thread and outside diameter together on the RFQ. Material, hardness and matching pins are not tabulated by the collected specification — RFQ lines.
What is the MOQ and lead time for DIN 1816 Round Nuts with Set-Pin Holes (Inside)?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for DIN 1816 Round Nuts with Set-Pin Holes (Inside) state?
State the full designation (DIN 1816), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 1816 Round Nuts with Set-Pin Holes (Inside) inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your DIN 1816 Round Nuts with Set-Pin Holes (Inside)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support