DIN 977 Hexagon Weld Nuts with Flange
DIN 977 hexagon weld nuts with flange, M5–M16 — the flanged hex nut resistance-welded onto sheet or bracket faces, with the collected flange/weld-face geometry ladder.
Last updated: 2026-11
Specifications
A DIN 977 weld nut puts a reusable machine thread onto a sheet-metal face where a tapped hole would be too thin to hold: the flange ring under the hex is the weld face, and resistance (projection) welding collapses it into the sheet in a fraction of a second, leaving a flush, permanent nut the paint line can run over. The collected ladder runs M5 to M16 and carries per size the flange diameter dc (15,5 → 36,5 mm), the nut height h (1,7 → 4 mm — these nuts sit low because the sheet, not the nut body, carries the joint), the weld-projection n (4 → 8), the hex width k across flats in its max./min. pair (5/4,7 at M5 up to 19,5/18,66 at M16), and the pitch columns — the source serves a small/large pitch pair, with the coarse series alone below M12. S and N are printed letter-only by the source; reproduce them with care (see the table note). Welding side matters: the flange goes against the electrode side with the projection ring set to collapse first, and the sheet must be bare at the weld spot — paint, scale and galvanising are removed or pierced before the weld. Where the joint is a stud-side rather than a nut-side thread, the weld stud pages in bolts are the counterpart; where the sheet is too thin for projection welding, a rivet nut (this catalog's rivets family) sets mechanically instead. Materials and plating are not tabulated by the collected specification — per RFQ.
| Standard | DIN 977 — hexagon weld nuts with flange (projection-weld flange ring under the hex) |
|---|---|
| Size range | M5 – M16, seven sizes in the collected ladder |
| Flange | dc: 15,5 → 36,5 mm across the ladder |
| Height / projection | h: 1,7 → 4 mm; weld-projection n: 4 → 8 |
| Hex width (k, max./min.) | 5 / 4,7 (M5) → 19,5 / 18,66 (M16) |
| Pitch | Coarse series only below M12 ("-" in the small-pitch column); from M12 the source lists small (1,5) and large (1,75 → 2) pitches |
| Materials / finishes | Not tabulated by the collected specification — per RFQ (state sheet thickness, material and weld schedule at quotation) |
| Thread (d) | P (small) | P (large) | Flange Dia. (dc) | h | n | k (max.) | k (min.) | S | N |
|---|---|---|---|---|---|---|---|---|---|
| M5 | - | 0,8 | 15,5 | 1,7 | 4 | 5 | 4,7 | 8 | 2,9 |
| M6 | - | 1 | 18,5 | 2 | 5 | 7 | 6,64 | 10 | 5,7 |
| M8 | - | 1,25 | 22,5 | 2,5 | 6 | 10 | 9,64 | 13 | 12,2 |
| M10 | - | 1,5 | 26,5 | 3 | 7 | 13 | 12,57 | 16 | 21,8 |
| M12 | 1,5 | 1,75 | 30,5 | 3 | 8 | 15 | 14,57 | 18 | 29,4 |
| M14 | 1,5 | 2 | 33,5 | 4 | 8 | 17 | 16,16 | 21 | 45,8 |
| M16 | 1,5 | 2 | 36,5 | 4 | 8 | 19,5 | 18,66 | 24 | 63,1 |
- Row 1 (M5): The S and N columns carry no legend in the collected capture (letter-only headers over a two-row flattened header); all figures are reproduced as printed. Verify against DIN 977 before quoting S/N-dependent process data (weld tip sizing).
Materials
- Material specified per RFQ — weldability drives the choice (low-carbon steel welds clean; check the weld schedule for coated or higher-alloy bodies); state the host sheet and electrode access with the order
Ordering & documentation
Documents
Shipments of DIN 977 Hexagon Weld Nuts with Flange are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 977 Hexagon Weld Nuts with Flange orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 977 Hexagon Weld Nuts with Flange), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 977 Hexagon Weld Nuts with Flange: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 977 hexagon weld nuts with flange is 10,000 pieces (applies to the standard sizes and finishes for din 977 hexagon weld nuts with flange; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 977 hexagon weld nuts with flange run 3–7 days. Quantities or variants of din 977 hexagon weld nuts with flange outside the standard range are confirmed at quotation.
Storage & shipping
DIN 977 Hexagon Weld Nuts with Flange are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 977 hexagon weld nuts with flange dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
DIN 977 or DIN 929 — which weld nut does my sheet want?
Both are projection weld nuts; they differ in what sits against the sheet. DIN 929 (covered in this catalog) is the hex with weld projections on the nut face and no flange — it sits proud and takes up less boss space. DIN 977 adds the flange ring under the hex: a larger, more forgiving weld face (dc 15,5 → 36,5 mm across M5–M16 in the collected table) that spreads the weld current and gives the painted assembly a broader bearing surface, at the cost of a bigger flat spot on the sheet. Practical read from the collected ladder: use the flanged DIN 977 when the sheet is thin enough that a six-projection hex face over-concentrates heat, or when the finished face wants the load spread; use DIN 929 on thicker sheet where the smaller print is an advantage. One caution from the capture: the source prints the S and N columns with letter-only headers — verify those figures against DIN 977 before they drive weld-tip sizing. Sheet thickness range, electrode schedule and plating are RFQ lines.
What is the MOQ and lead time for DIN 977 Hexagon Weld Nuts with Flange?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for DIN 977 Hexagon Weld Nuts with Flange state?
State the full designation (DIN 977), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 977 Hexagon Weld Nuts with Flange inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your DIN 977 Hexagon Weld Nuts with Flange
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support