DIN 28129 Clamp Nuts for Covers (M12 – M30)

DIN 28129 clamp nuts for covers — flange-form clamp nuts seating on inspection and manhole cover flanges of vessels and containers, tabulated d1/d2/d3/h/m over M12 to M30 (d2 12-20, flange d3 30-50, height h 45-58, m 22-35).

Last updated: 2026-11

Request a Quote

DIN 28129 Clamp Nuts for Covers (M12 – M30) in an industrial setting
Illustrative image redrawn from real DIN 28129 Clamp Nuts for Covers (M12 – M30) product references — not a photograph of stocked items.

Specifications

DIN 28129 is a vessel-specific clamp nut: the retaining nut that clamps bolted-down inspection covers, manhole lids and handhole covers on pressure vessels and process containers, sized to the cover-bolt ladder (M12 to M30) rather than to a general hex-nut series. The part is taller than a standard hex nut (h 45 to 58 across the ladder, versus roughly 0.8-1×d for a plain nut) because it must clamp the cover plate plus gasket stack and still carry full thread engagement on the stud — and the print shows the flange doing the seating work: d3 (30 to 50) bears on the cover or the clamp lug while d2 (12 to 20) is the washer-face/clearance diameter. This designation lives almost exclusively in vessel and equipment engineering (the DIN 28xxx series is the vessel-apparatus norm family), so the practical buyer is a vessel manufacturer, a retrofit shop replacing corroded clamp hardware, or a maintenance buyer matching an existing cover by thread and seat diameter. Reading notes before engineering use: the grid prints identical d2/d3/h/m values for M24, M27 and M30 as captured — one shared body size across the three largest threads, as the source prints it; and the source prints no material or finish line, so coating state (these are commonly galvanized for outdoor vessel duty) is a quotation confirmation, not a page claim. Match by thread AND seat: the stud thread alone does not fix the part — d3 must fit the cover's clamping bore or the nut bridges it unevenly.

Standard / scope DIN 28129 clamp nuts for covers (inspection/manhole cover clamp nuts on vessels and containers)
Threads tabulated (d1) M12, M16, M20, M24, M27, M30 — six printed rows
d2 (washer face / clearance) 12 / 14 / 16 / 20 / 20 / 20 — identical 20 across the M24-M30 rows as printed
d3 (seat / bearing diameter) 30 / 35 / 40 / 50 / 50 / 50 (M12 → M30)
h (height) / m (width) h: 45 / 48 / 50 / 58 / 58 / 58; m: 22 / 25 / 28 / 35 / 35 / 35 — duplicate values across M24-M30 as printed
Not tabulated No material, finish, or equivalents line printed on the source page — coating state and material are quotation confirmations
Clamp nuts for covers to DIN 28129dimensions in mm; attribute legend per the source columns: d1 - thread, d2 - washer face / clearance diameter, d3 - seat / bearing diameter, h - height, m - width
d1d2d3hm
M1212304522
M1614354825
M2016405028
M2420505835
M2720505835
M3020505835
  • the M24, M27 and M30 rows print identical d2/d3/h/m values (20 / 50 / 58 / 35) — one shared body print across the three largest threads, as captured.
  • the source prints no tolerance bands, material or finish lines — the grid is the page's only dimension authority.

Materials

  • The source page prints no makings line — no steel grade, no galvanizing or stainless print — so this page makes no material claim beyond the geometry grid. In trade practice vessel clamp hardware is most commonly supplied in steel with galvanized coating for outdoor/ambient duty, with stainless quoted for corrosive or food-grade plants, but both are quotation confirmations here. State the thread (M12-M30 from the ladder), the seat check (d3 against your cover's clamping bore), material and coating explicitly, any certificate requirement, and quantity per size — retrofit buyers should measure the failed part's d3 before ordering by thread alone.

Ordering & documentation

Documents

Shipments of DIN 28129 Clamp Nuts for Covers (M12 – M30) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 28129 Clamp Nuts for Covers (M12 – M30) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 28129 Clamp Nuts for Covers (M12 – M30)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 28129 Clamp Nuts for Covers (M12 – M30): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 28129 clamp nuts for covers (m12 – m30) is 10,000 pieces (applies to the standard sizes and finishes for din 28129 clamp nuts for covers (m12 – m30); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 28129 clamp nuts for covers (m12 – m30) run 3–7 days. Quantities or variants of din 28129 clamp nuts for covers (m12 – m30) outside the standard range are confirmed at quotation.

Storage & shipping

DIN 28129 Clamp Nuts for Covers (M12 – M30) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 28129 clamp nuts for covers (m12 – m30) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why not just use a standard hex nut on a cover stud?

Because the cover stack needs the seat, not just the thread. A standard hex nut clamps on its washer face at roughly the thread diameter, which digs into plastic cover plates, bridged gaskets or worn clamp lugs; DIN 28129 carries a defined seat diameter d3 (30-50) and extra height h (45-58) so the clamping load spreads over the intended bearing ring and the stud keeps full engagement through cover + gasket thickness. On a vessel cover the hardware also tends to be standardized as a set — stud, clamp nut, and cover bore all sized from the same DIN 28xxx ladder — so mixing a general-purpose nut in breaks the seat match even when the thread fits.

M24, M27 and M30 print the same body dimensions — is one part interchangeable across all three threads?

The grid prints identical d2/d3/h/m (20 / 50 / 58 / 35) for the three largest threads as captured — the body geometry is shared, but the threads are not: M24, M27 and M30 have different pitches and stud fits, so the nuts are distinct parts that happen to share a body print. For a retrofit buyer that is useful: the seat and clearances match across the three sizes, so checking d3 once covers the family — but you still order by exact thread. If your cover was built to a different seat diameter than the print, measure before ordering; the source grid is the only dimension authority this page carries.

What should an RFQ for DIN 28129 clamp nuts state?

Thread size (M12-M30 from the ladder), the seat check as a stated dimension (d3 against the cover's clamping bore — especially on retrofits where the original hardware may not match the current print), material and coating (the source prints none — galvanized/stainless is a quotation confirmation), any certificate requirement for the pressure-equipment file, and quantity per size. Nuts for cover hardware on coded vessels usually need documentation to match — state it up front rather than at delivery.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 28129 Clamp Nuts for Covers (M12 – M30) inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your DIN 28129 Clamp Nuts for Covers (M12 – M30)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.