DIN 439 Thin Hex Jam Nuts

Thin hexagonal jam nuts per DIN 439 — about half the thickness of a standard hex nut (0.5 × diameter), in unchamfered Type A and chamfered Type B, right- and left-hand thread, M2 to M60 in steel, brass and stainless A2/A4. The lock nut you jam against a full nut, and the low-profile answer where a standard nut is too thick.

Last updated: 2026-11

Request a Quote

DIN 439 Thin Hex Jam Nuts in an industrial setting
Illustrative image redrawn from real DIN 439 Thin Hex Jam Nuts product references — not a photograph of stocked items.

Specifications

A jam nut is a hex nut cut down to roughly half height — the collected DIN 439 spec puts it at 0.5 × diameter — and its two jobs both follow from that. Job one is locking: run the thin nut up against a standard nut and jam the pair against each other, and the assembly resists back-off without a nylon insert or deformed threads, which is why jam nuts appear on adjustment threads and turned linkages where the lock must survive re-tuning. Job two is clearance: where a full-height hex nut simply will not fit — shallow threads on a shaft end, a thin flange, a compact housing — the jam nut takes the thread with enough engagement for the application at half the stack height. DIN 439 covers both finishes, unchamfered Type A and chamfered Type B, in right- and left-hand thread, from M2 to M60 in steel, brass and stainless A2/A4. Torque the pair properly — hold the jam nut back while the full nut torques against it — or the "lock" is just two loose nuts.

Standard DIN 439 — thin hexagonal jam nut, thickness 0.5 × diameter
Forms Type A unchamfered / Type B chamfered; right-hand and left-hand thread
Locking use Threaded up against a standard nut, locking it in place
Clearance use Low-profile alternative where a standard nut is too thick for the application
Size range Stock M2 – M60; dimensions tabulated M2 – M48
Dimensions at M10 Width across flats s = 17 mm; thickness m = 5 mm
Series highlights (s × m, mm) M6 10 × 3.2 · M8 13 × 4 · M12 19 × 6 · M16 24 × 8 · M20 30 × 10 · M24 36 × 12
Materials Steel, brass, stainless steel A2 and A4
Typical applications Lock-nut pairs on adjustment and linkage threads; low-clearance fastening on shaft ends and thin flanges

Materials

  • Steel
  • Brass
  • Stainless steel A2
  • Stainless steel A4

DIN 439 is the thin jam nut: same thread size and pitch as the standard hex nut at a low profile, used as a secondary nut locking against a primary nut or where clearance is tighter than a full-height nut allows.

The dimension data makes the profile consequence concrete: at 1/4 in size the jam nut runs 5/32 basic thickness (0.163 max) against the full hex nut's 7/32 (0.226 max) on the same 3/4 in width across flats — about two-thirds the height. Material pairs like the parent hex nut: steel for strength, brass where conductivity or appearance leads, stainless A2 for normal atmosphere and A4 for chloride service — and stainless pairs need anti-seize because stainless-on-stainless threads gall.

Ordering & documentation

Documents

Shipments of DIN 439 Thin Hex Jam Nuts are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 439 Thin Hex Jam Nuts orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 439 Thin Hex Jam Nuts), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 439 Thin Hex Jam Nuts: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 439 thin hex jam nuts is 10,000 pieces (applies to the standard sizes and finishes for din 439 thin hex jam nuts; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 439 thin hex jam nuts run 3–7 days. Quantities or variants of din 439 thin hex jam nuts outside the standard range are confirmed at quotation.

Storage & shipping

DIN 439 Thin Hex Jam Nuts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 439 thin hex jam nuts dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

How do I install a jam nut so it actually locks?

Order matters. Thread the jam nut on first, bottom it lightly, then run the full nut on top and torque the full nut against it while holding the jam nut back with a thin wrench — the two nuts load against each other and that axial preload is the lock. Tightening the pair "as one" leaves both loose and locks nothing. Because the thin nut carries the backlash, some practice puts the jam nut on the bottom so the full nut takes the wrench torque; either way, the lock comes from the counter-tension between the two, not from thread deformation. For re-tuned adjustment points, check the pair after each re-setting — a jam-nut lock is a service habit, not a one-time fit.

What is the MOQ and lead time for this nut type?

The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Common diameters in this nut type are widely stocked; confirm the exact schedule against quantity and size mix at quotation.

What should an RFQ for this nut type state?

State the standard designation (for example DIN 985 or DIN 6923), nominal thread size and pitch (metric coarse unless fine pitch is required), material and strength pairing with the mating bolt, finish (plain, zinc, or hot-dip galvanized where compatible), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 439 Thin Hex Jam Nuts inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your DIN 439 Thin Hex Jam Nuts
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.