ASME B18.2.4.6M Heavy Hex Nuts (Metric)
Metric heavy hex nuts per ASME B18.2.4.6M — dimension table M12 to M100: width across flats/corners, thickness M, bearing face diameter Dw, washer face thickness C, and bearing-surface total runout FIM, the metric counterpart of the imperial heavy hex nut.
Last updated: 2026-11
Specifications
B18.2.4.6M is the metric heavy hex nut — the mate for the B18.2.3.3M and B18.2.6M heavy hex screws and bolts — and the collected table runs an unusually deep ladder, M12 to M100, where most nut pages stop at M64. The heavy signature is in the across-flats column: as tabulated, M12: 21.00/20.16, M16: 27.00/26.16, M30: 50.00/49.00, M100: 150.00/145.00 — the same heavy wrench ladder the heavy bolts use, so one wrench set serves the joint. Thickness M max/min (12.3/11.9 at M12 up to 100.0/97.8 at M100) is the dimension that separates a heavy nut from a jam or standard-thickness nut: at roughly 1.0 x nominal diameter minus a small trim, it is the thread engagement high-preload joints are designed around. Bearing face Dw min (19.2 at M12, 137.8 at M100), washer face thickness C (0.8/0.4 rising to 1.2/0.6) and the total runout of bearing surface FIM max (0.38 at M12 to 2.62 at M100) define the seating quality — on a heavy structural joint, runout is the acceptance check that keeps the load centered on the bearing face rather than on a chamfered edge. Proof loads and property classes are not tabulated — per RFQ.
| Standard | ASME B18.2.4.6M — metric heavy hex nuts, sizes M12 - M100 (coarse thread ladder as tabulated) |
|---|---|
| Width across flats S | Heavy ladder max/min (M12: 21.00/20.16; M16: 27.00/26.16; M24: 41.00/40.00; M36: 60.00/58.80; M100: 150.00/145.00) — pairs with the B18.2.6M / B18.2.3.3M heavy bolt wrench sizes |
| Width across corners E | Max/min (M12: 24.25/22.78; M36: 69.28/66.44; M100: 173.21/165.30) |
| Thickness M | Max/min (M12: 12.3/11.9; M16: 17.1/16.4; M36: 36.6/35.0; M100: 100.0/97.8) — the heavy-nut engagement dimension |
| Bearing face | Dw min (M12: 19.2; M24: 38.0; M100: 137.8), washer face thickness C max/min (0.8/0.4 at M12 rising to 1.2/0.6 at M100), total runout of bearing surface FIM max (0.38 at M12 to 2.62 at M100) |
| Not tabulated | Proof loads, property classes (ISO 898-2 class / ASTM A194 grades), finish — per RFQ |
| Nominal Dia. | Width Across Flats, S | Width Across Flats, S | Width Across Corners, E | Width Across Corners, E | Thickness, M | Thickness, M | Bearing Face Dia., Dw | Washer Face Thickness, C | Washer Face Thickness, C | Total Runout of Bearing Surface FIM |
|---|---|---|---|---|---|---|---|---|---|---|
| Nominal Dia. | Max. | Min. | Max. | Min. | Max. | Min. | Min. | Max. | Min. | Max. |
| M12 | 21.00 | 20.16 | 24.25 | 22.78 | 12.3 | 11.9 | 19.2 | 0.8 | 0.4 | 0.38 |
| M14 | 24.00 | 23.16 | 27.71 | 26.17 | 14.3 | 13.6 | 22.0 | 0.8 | 0.4 | 0.42 |
| M16 | 27.00 | 26.16 | 31.18 | 29.56 | 17.1 | 16.4 | 24.9 | 0.8 | 0.4 | 0.47 |
| M20 | 34.00 | 33.00 | 39.26 | 37.29 | 20.7 | 19.4 | 31.4 | 0.8 | 0.4 | 0.58 |
| M22 | 36.00 | 35.00 | 41.57 | 39.55 | 23.6 | 22.3 | 33.3 | 0.8 | 0.4 | 0.63 |
| M24 | 41.00 | 40.00 | 47.34 | 45.20 | 24.2 | 22.9 | 38.0 | 0.8 | 0.4 | 0.72 |
| M27 | 46.00 | 45.00 | 53.12 | 50.85 | 27.5 | 26.3 | 42.8 | 0.8 | 0.4 | 0.80 |
| M30 | 50.00 | 49.00 | 57.74 | 55.37 | 30.7 | 29.1 | 45.6 | 0.8 | 0.4 | 0.87 |
| M36 | 60.00 | 58.80 | 69.28 | 66.44 | 36.6 | 35.0 | 55.9 | 0.8 | 0.4 | 1.05 |
| M42 | 70.00 | 67.90 | 80.83 | 77.41 | 42.0 | 40.4 | 64.5 | 1.0 | 0.5 | 1.22 |
| M48 | 80.00 | 77.60 | 92.38 | 88.46 | 48.0 | 46.4 | 73.7 | 1.0 | 0.5 | 1.40 |
| M56 | 90.00 | 87.20 | 103.92 | 99.41 | 56.0 | 54.1 | 82.8 | 1.0 | 0.5 | 1.57 |
| M64 | 100.00 | 96.80 | 115.47 | 110.35 | 64.0 | 62.1 | 92.0 | 1.0 | 0.5 | 1.75 |
| M72 | 110.00 | 106.40 | 127.02 | 121.30 | 72.0 | 70.1 | 101.1 | 1.2 | 0.6 | 1.92 |
| M80 | 120.00 | 116.00 | 138.56 | 132.24 | 80.0 | 78.1 | 110.2 | 1.2 | 0.6 | 2.09 |
| M90 | 135.00 | 130.50 | 155.88 | 148.77 | 90.0 | 87.8 | 124.0 | 1.2 | 0.6 | 2.36 |
| M100 | 150.00 | 145.00 | 173.21 | 165.30 | 100.0 | 97.8 | 137.8 | 1.2 | 0.6 | 2.62 |
Materials
- Metric heavy hex nuts ship in carbon steel by property class (class 10 and 12 for the metric line; ASTM A194 2H/2HM where the imperial piping world calls the metric size) and stainless A2/A4. Nut class must be paired to the bolt class on the RFQ — a heavy nut is geometry, not strength, and the collected table carries geometry only
Ordering & documentation
Documents
Shipments of ASME B18.2.4.6M Heavy Hex Nuts (Metric) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ASME B18.2.4.6M Heavy Hex Nuts (Metric) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ASME B18.2.4.6M Heavy Hex Nuts (Metric)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for ASME B18.2.4.6M Heavy Hex Nuts (Metric): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for asme b18.2.4.6m heavy hex nuts (metric) is 10,000 pieces (applies to the standard sizes and finishes for asme b18.2.4.6m heavy hex nuts (metric); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for asme b18.2.4.6m heavy hex nuts (metric) run 3–7 days. Quantities or variants of asme b18.2.4.6m heavy hex nuts (metric) outside the standard range are confirmed at quotation.
Storage & shipping
ASME B18.2.4.6M Heavy Hex Nuts (Metric) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store asme b18.2.4.6m heavy hex nuts (metric) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Which nut goes on a B18.2.6M heavy hex bolt — and can a standard hex nut be substituted?
The heavy nut, B18.2.4.6M, and the substitution is a real derating. The collected table shows what the heavy nut provides: thickness M at roughly the full nominal diameter (12.3 mm at M12, 100 at M100) against visibly less on a standard-thickness nut, and the same across-flats ladder as the heavy bolt head (21 mm at M12), so the assembly turns with one wrench. A standard hex nut threads on and can clamp, but its shorter engagement reduces the shear area carrying the load — the margin high-preload joints size for — and its lighter across-flats means the wrench that tightened the bolt cannot turn the nut without slipping. Match the designations: B18.2.6M or B18.2.3.3M bolt with B18.2.4.6M nut, class paired to class, both named on the RFQ.
Why does the table run to M100 — and what does FIM mean at that size?
Because heavy metric nuts live in industries that build big: heavy equipment, structural towers, large flange systems — where M64 to M100 fasteners are ordered, not improvised. At those sizes the collected table's runout column becomes the quality gate worth asking about: total runout of bearing surface FIM max rises from 0.38 mm at M12 to 2.62 mm at M100, the permitted tilt of the washer face relative to the thread axis. On an M100 nut that face is nearly 150 mm across (Dw min 137.8), so a runout at the limit seats the nut like a slightly wedged washer — the clamp load concentrates on one arc of the face instead of the full annulus. For critical joints, ask for the actual runout on the certificate alongside proof-load test evidence; the geometry table gets you the right part, the certificate gets you the right part verified. Both property class and proof load stay per RFQ — the collected page does not tabulate them.
What is the MOQ and lead time for ASME B18.2.4.6M Heavy Hex Nuts (Metric)?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for ASME B18.2.4.6M Heavy Hex Nuts (Metric) state?
State the full designation (ASME B18.2.4.6M), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ASME B18.2.4.6M Heavy Hex Nuts (Metric) inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your ASME B18.2.4.6M Heavy Hex Nuts (Metric)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support