ISO 2982 Rolling Bearing Lock Nuts

ISO 2982 part 2 rolling bearing lock nuts, 4-slot and 8-slot series: metric M10–M200 and Tr 210–Tr 1000 threads with pitch, d2/d3 diameters, height h, slot b and t.

Last updated: 2026-11

Request a Quote

ISO 2982 Rolling Bearing Lock Nuts in an industrial setting
Illustrative image redrawn from real ISO 2982 Rolling Bearing Lock Nuts product references — not a photograph of stocked items.

Specifications

ISO 2982 part 2 is the locknut that clamps bearings, sleeves and gear faces onto threaded shafts — the collected 04/2013-edition tables carry both series the standard defines: the 4-slot locknut from M10 through M200 (plus the transition into the Tr metric trapezoidal thread series) and the 8-slot locknut running Tr 220 up to Tr 1120 for the largest shafts. Per size the tables give pitch (1 at M10 to 4 at M200-class, 7 across the large Tr sizes), the precision diameters d2 and d3 (350/320.0 at Tr 280) — d3 being the runout-critical face-bearing diameter that decides the locknut's seating quality — height h (38 at Tr 280, up to 125 on the larger 8-slot sizes), slot width b and slot depth t. The 8-slot series exists for the locking pin loads of big bearings: eight slots give a finer angular indexing of the tightening position, which at these thread pitches is the difference between correct and excessive clamping.

Standard / scope ISO 2982 part 2 locknuts — 4-slot series M10–M200 + Tr transition (edition 04/2013, supersedes ISO 2982:1995-08); 8-slot series Tr 220–Tr 1120 (2013)
Threads / pitch Metric M10 (P 1) to M200 (P 4); Tr trapezoidal Tr 210–Tr 1120 (P 4 to 7) — pitch column printed per size
Precision diameters d2 and d3 per size (Tr 280: 350 / 320.0) — d3 is the seating-face diameter, the runout-critical dimension
Height / slots h per size (38 at Tr 280, 125 on the larger 8-slot sizes); slot width b (24 at Tr 280) and depth t (12)
Not tabulated Tolerance class, face runout values, locking element (lockwasher MB / clip), material — per RFQ
ISO 2982 part 2 locknuts with 4 slots — 04/2013 edition, geometry by thread d1 (metric and Tr series as printed)Dimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
d1 thread sizePitchd2d3hbt
M 100.751813.5432
M 1212217.0432
M 1512521.0542
M 1712824.0542
M 2013226.0642
M 251.53832.0752
M 301.54538.0752
M 351.55244.0852
M 401.55850.0962.5
M 451.56556.01062.5
M 501.57061.01162.5
M 5527567.01173
M 6028073.01173
M 6528579.01273
M 7029285.01283.5
M 7529890.01383.5
M 80210595.01583.5
M 852110102.01683.5
M 902120108.016104
M 952125113.017104
M 1002130120.018104
M 1052140126.018125
M 1102145133.019125
M 1152150137.019125
M 1202145135.020125
M 1202155138.020125
M 1252160148.021125
M 1302155145.021125
M 1302165149.021125
M 1352175160.022146
M 1402165155.022145
M 1402180160.022146
M 1452190171.024146
M 1502180170.024145
M 1502195171.024146
M 1553200182.025167
M 1603190180.025165
M 1603210182.025167
M 1653210193.026167
M 1703200190.026165
M 1703220190.326167
M 1803210200.027185
M 1803230203.027188
M 1903220210.028185
M 1903240214.028188
M 2003240220.029188
M 2003250226.029188
Tr2104270238.0302010
Tr2204280250.0322010
Tr2304290260.0342010
Tr2404300270.0342010
Tr2504320290.0362010
Tr2604330300.0362412
Tr2804350320.0382412
  • Source spanning title row carried verbatim: "Dimensions in mm - source ISO 2982 part 2 Locknut with 4 slots".
  • Edition row carried from the source grid: "Publication date: 04/2013SupersedesISO 2982:1995-08".
  • Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (8/7) — grid padded empty; per-row pre-pad widths: 8,8,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7.
ISO 2982 part 2 locknuts with 8 slots — 2013 edition, geometry by thread d1Dimensions in mm unless stated; cell values, symbols and decimal marks exactly as printed on the source page. Column 1 is the row label.
d1 thread sizePitchd2d3hbt
Tr220426024230209
Tr2404290270342010
Tr2604310290342010
Tr2804330310382410
Tr3004360336422412
Tr3004380340402412
Tr3205380356422412
Tr3205400360422412
Tr3405400376452412
Tr3405440400552815
Tr3605420394452813
Tr3605460420582815
Tr3805450422482814
Tr3805490440603218
Tr4005470442522814
Tr4005520460623218
Tr4205490462523214
Tr4205540490703218
Tr4405520490603215
Tr4405560510703620
Tr4605540510603215
Tr4605580540753620
Tr4805560530603615
Tr4805620560753620
Tr5005630580804015
Tr5005580550683623
Tr5306630590684020
Tr5306670610804023
Tr5606650610754020
Tr5606710650854525
Tr6006700660754020
Tr6006750690854525
Tr6306730690754520
Tr63068000730955028
Tr67067800740804520
Tr670685007751065028
Tr71078300780905025
Tr710790008251065530
Tr75078700820905525
Tr750795008751126034
Tr80079200870905525
Tr8007100009251126034
Tr85079800925906025
Tr8507106009751187038
Tr9007103009751006025
Tr9007112010301257038
Tr9507108010251006025
Tr9507117010801257038
Tr10007114010851006028
Tr10007124011401257038
Tr10607120011451006025
Tr10607130012101257038
Tr11207126012051006025
  • Source spanning title row carried verbatim: "Dimensions in mm - source ISO 2982 Part 2 Locknut with 8 slots".
  • Edition row carried from the source grid: "Publication date: 2013".
  • Row-width mismatch in the source grid: source rows carry differing non-empty cell counts (8/7) — grid padded empty; per-row pre-pad widths: 8,8,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7.

Materials

  • Bearing locknuts order in hardened and tempered steel with the d3 face ground — the face is the bearing surface and its flatness, not the thread, is what the grade sells; stainless and coated variants for corrosive plants. Order the locknut with its locking element (DIN 5406 MB lockwasher — registered here — or locking clip) and state the shaft thread designation including pitch, because the Tr series shares nominal sizes across pitches

Ordering & documentation

Documents

Shipments of ISO 2982 Rolling Bearing Lock Nuts are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 2982 Rolling Bearing Lock Nuts orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ISO 2982 Rolling Bearing Lock Nuts), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for ISO 2982 Rolling Bearing Lock Nuts: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for iso 2982 rolling bearing lock nuts is 10,000 pieces (applies to the standard sizes and finishes for iso 2982 rolling bearing lock nuts; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 2982 rolling bearing lock nuts run 3–7 days. Quantities or variants of iso 2982 rolling bearing lock nuts outside the standard range are confirmed at quotation.

Storage & shipping

ISO 2982 Rolling Bearing Lock Nuts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 2982 rolling bearing lock nuts dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why does the range switch from metric M threads to Tr trapezoidal threads?

Load per turn. Below M200-class the locknut tightens with a hook spanner and the metric thread carries the clamp; on large shafts the tightening torque becomes enormous, and the Tr trapezoidal thread — deeper, stronger flanks, coarser pitch — survives the wrench work and the service re-tightening without deforming. That is why the collected tables split at the M200/Tr boundary: the 4-slot series is spanner territory, the 8-slot series enters the world where tightening is a two-person, torque-monitored job. When ordering, quote the full shaft thread including pitch ("Tr 280 × 4") — several Tr nominal diameters exist in two pitches and the d2/d3 geometry follows the pitch, not just the size.

4 slots or 8 slots — and what does slot count actually buy me?

Angular indexing. The lockwasher tongue or locking clip engages a slot, so the nut can only lock at positions where a slot aligns — more slots mean finer steps between lockable positions. On a fine-pitch small nut the 4-slot steps are already tight enough to reach correct clamp; on a Tr 280 × 4 one slot-step rotates the face several hundredths of a millimetre axially, which is real bearing clearance, so the 8-slot series halves the step. The practical rule the two tables encode: follow the bearing/sleeve manufacturer's series call-out (they sized the shaft end for it), and when designing new, count the clamp resolution you need against the pitch — the h and t columns here give the geometry both series share.

What is the MOQ and lead time for ISO 2982 Rolling Bearing Lock Nuts?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for ISO 2982 Rolling Bearing Lock Nuts state?

State the full designation (ISO 2982 Rolling Bearing Lock Nuts), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ISO 2982 Rolling Bearing Lock Nuts inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your ISO 2982 Rolling Bearing Lock Nuts
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.