DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d)

DIN 6330 hexagon clamping nuts, M6 to M48 — the tall 1.5 × d hex nut with machined bearing surfaces for jig, fixture and clamping assemblies, with the collected per-size table: d1 (h14), da, e, m, r, s with h13/h14 limit deviations and reference mass per 1000 units.

Last updated: 2026-11

Request a Quote

DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d) in an industrial setting
Illustrative image redrawn from real DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d) product references — not a photograph of stocked items.

Specifications

DIN 6330 is the tall hex nut of the clamping world: at one and a half times the thread diameter in height — nearly double a standard hex nut — it gives a wrench or tommy bar more engaged thread and more bearing face on jig plates, clamping fixtures and workholding sets, which is why it shares its drawings with fit bolts and clamp studs rather than with ordinary structural bolting. The collected table runs M6 through M48 and carries the machined-nut signatures: a turned d1 boss dimensioned with an h14 shaft tolerance, the s width across flats with actual limit deviations (h13 through M20, h14 from M24) instead of the free-run tolerance an ordinary hot-stamped nut gets, and a height column m that lands on exactly 1.5 × d in every size — the arithmetic you can use to sanity-check any supplier's sheet. Note the companion numbers so the right nut arrives: DIN 6331 is this nut's collared sister — the same 1.5 × d clamping nut with a raised locating boss for counterbored pockets (it has its own page in this catalog) — and the thin-height counterpart of this nut lives in the jam-nut pages of this catalog. Property classes, materials and finishes are not tabulated by the collected reference — state the duty (jig, fixture, press tool) and the mating stud at quotation.

Standard / scope DIN 6330 hexagon clamping nuts, height 1.5 × d, M6 to M48 (also referenced as PN 61272 by the collected source's cross-reference panel)
Height m = 1.5 × d across the whole ladder (9 at M6 up to 72 at M48) — the table lands on the ratio exactly in all eleven sizes
Width across flats s 10 → 75 with printed limit deviations h13 (M6–M20) and h14 (M24–M48) — machined-nut tolerances, not free-run
d1 / da d1 (h14) 7 → 52; da max 7 → 50 — turned boss dimensions for fixture assembly
Across corners e 11,05 → 83,91 (decimal commas as printed by the source)
Reference mass Approx. 5 → 1800 kg per 1000 units at 7,85 kg/dm3 (source basis note)
Materials / property classes Not tabulated by the collected reference — per RFQ (tenant supply range: steel, stainless steel; grade and finish confirmed at quotation)
DIN 6330 hexagon clamping nuts, height 1.5 × d (M6 – M48) — collected dimensionsAll dimensions in millimetres; mass is the source's approximate figure per 1000 units at 7,85 kg/dm3. The s limit-deviation column is transcribed verbatim from the source's data cells (h13 / h14). Property classes, materials and finishes are not tabulated — per RFQ.
dd1 (h14)da (max.)emrss limit deviationApprox. mass per 1000 units (7,85 kg/dm3), kg
M67711,059910h135
M89914,38121113h139,6
M1011,51117,77151516h1321
M12141320,03181718h1331,5
M16181726,75242224h1361
M20222133,53302730h13120
M24262539,98363236h14206
M30323151,28454146h14419
M36383761,31545055h14715
M42444372,61635865h141170
M48525083,91726775h141800
  • Header rowspan mismatch in the source grid: row 1 prints 8 cells, row 2 prints 7, data rows print 9. The sub-header js15 sits over the e position and "Limit deviatios" [sic, source typo] over the r/s region; tolerance attribution is kept as printed here and not adjudicated.
  • The r column (9 at M6 up to 67 at M48) matches neither a fillet radius nor a simple fraction of s; the values are transcribed as printed under the source's own header letter, flagged for quoting engineers.
  • s carries shaft-grade limit deviations (h13 for M6–M20, h14 for M24–M48), unusual for a nut and consistent with a machined clamping nut; the deviation was printed inside the s header region, not per row — lifted verbatim into its own column without interpretation.
  • Height consistency check passed: the m column equals 1.5 × d exactly in all eleven rows, matching the source page subtitle "height 1.5 xD".

Materials

  • Steel, stainless steel — grade, property class and finish confirmed at quotation (tenant supply range); the collected dimension reference tabulates no material or class rows

Ordering & documentation

Documents

Shipments of DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 6330 hexagon clamping nuts (height 1.5 × d) is 10,000 pieces (applies to the standard sizes and finishes for din 6330 hexagon clamping nuts (height 1.5 × d); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 6330 hexagon clamping nuts (height 1.5 × d) run 3–7 days. Quantities or variants of din 6330 hexagon clamping nuts (height 1.5 × d) outside the standard range are confirmed at quotation.

Storage & shipping

DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 6330 hexagon clamping nuts (height 1.5 × d) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

How is a DIN 6330 clamping nut different from a standard hex nut like DIN 934 / ISO 4032?

Height and machining. A standard hex nut runs about 0.8 × d tall; DIN 6330 is 1.5 × d — at M12 that is 18 mm of height against roughly 10 — so more threads carry the clamp and the wrench has room to work in a fixture stack. The collected table also shows the machining: s carries real limit deviations (h13/h14), and d1 is dimensioned with an h14 shaft tolerance — tolerances an ordinary stamped nut never claims. That is why clamp nuts seat square on jig plates and resist the brinelling a rough nut face would leave. The trade is cost and lead time: machined nuts in small volumes price well above commodity hex nuts, so they belong where the clamp repeats — fixtures and workholding — not across a structure.

What does an RFQ for DIN 6330 nuts need to state?

Thread size and the DIN 6330 number as the drawing prints it, plus the mating stud (fit bolt, clamp stud or threaded mandrel) and its standard, so the thread fit is checked on both parts. Add material and finish for the environment, quantity, and any certificate requirement such as a mill test report per EN 10204 3.1. If the fixture drawing dimensions the nut pocket, send the pocket dimension too — the turned d1 boss and the toleranced s width are what the pocket sees, and the table on this page gives both per size. Sizes or heights outside the standard table (for example long-jam variants) are quoted to drawing.

DIN 6330 or DIN 6331 — which number is which nut?

Both numbers are nuts, and both are the tall 1.5 × d clamping type. DIN 6330 is the plain clamping nut tabulated on this page; DIN 6331 is its collared variant — the same nut with a raised locating boss (boss diameter d1, boss height a) that seats in a counterbored fixture pocket and keeps the nut from spinning or wandering under the wrench. The pair is easy to transpose because quotes and drawings often list them together, so state the variant — plain or collared — alongside the DIN number on the RFQ; the tables differ (DIN 6331 carries the boss dimensions a and d1 that DIN 6330 does not) and a transposed number ships a nut that will not seat in the pocket.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d) inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your DIN 6330 Hexagon Clamping Nuts (Height 1.5 × d)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.