ISO 299 Nuts for T-Slots
ISO 299 T-slot nuts M4 to M48 — the tongue-and-key machine-table nut that slides into the T-slot and clamps workholding down, with the collected a/e/f/h/k/d/F geometry ladder and per-1000 weight.
Last updated: 2026-11
Specifications
The T-slot nut is the workholding keystone of every machine table: a threaded block with a tongue (width a) that slides into the table's T-slot and a key cut (offset f, depth d) that stops it from turning when the stud is tightened. ISO 299 is the ISO designation for that nut; this catalog already carries the DIN 508 identity (the DIN counterpart), and this page is the ISO designation with its own collected column set — the source tabulates the slot-fit envelope here (F min. = the minimum T-slot width the nut fits, e = nut height) that the DIN page's capture carries as DIN 650 slot numbers instead. The collected ladder runs M4 to M48 with tongue width a in nominal/max./min. (5 mm nominal at M4 up to 54 at M48), nut height e nominal/min. (9/8,5 up to 85/84), key offset f (1 → 6), total height h (6,5 → 70), key height k nominal/min. (3/2,7 → 34/33), tongue depth d (5 → 54), slot width F min. (7 → 653 with a flagged plateau at the large end) and weight per 1000 pcs (2,5 kg → 2300 kg). Two verbatim print defects are flagged and not normalized: the M36 row prints e min. 54 against the ladder's max-minus-≈1 progression, and F min. repeats 653 unchanged across M36/M42/M48. Fit discipline: tongue width a must slide but not rock in the slot — the nominal/max./min. triple is the clearance envelope. Material and hardness (these nuts see stud torque and hammering) are not tabulated — per RFQ; case-hardened is the trade default, confirm at quotation.
| Standard | ISO 299 — nuts for T-slots (ISO designation; DIN 508 is the DIN counterpart identity) |
|---|---|
| Size range | M4 – M48, thirteen sizes in the collected ladder |
| Tongue | a: 5 → 54 mm (nominal/max./min. triple); offset f: 1 → 6; depth d: 5 → 54 |
| Nut height | e nominal 9 → 85 (min. 8,5 → 84; M36 min. cell flagged verbatim); total h: 6,5 → 70 |
| Key | k nominal 3 → 34 (min. 2,7 → 33) |
| Slot fit | F min. (minimum T-slot width): 7 → 653 — plateau 653 at M36/M42/M48 flagged verbatim |
| Weight | kg/1000 pcs: 2,5 (M4) → 2300 (M48) |
| Material / hardness | Not tabulated by the collected specification — per RFQ |
| Thread d | a nominal size | a max. | a min. | e nominal size max. | e min. | f | h | k nominal size max. | k min. | Weight kg/1000pcs | d | F min. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M4 | 5 | 4,7 | 4,5 | 9 | 8,5 | 1 | 6,5 | 3 | 2,7 | 2,5 | 5 | 7 |
| M5 | 6 | 5,7 | 5,5 | 10 | 9,5 | 1,6 | 8 | 4 | 3,5 | 4 | 6 | 11,4 |
| M6 | 8 | 7,7 | 7,5 | 13 | 12,5 | 1,6 | 10 | 6 | 5,5 | 10 | 8 | 16 |
| M8 | 10 | 9,7 | 9,5 | 15 | 14,5 | 1,6 | 12 | 6 | 5,5 | 18 | 10 | 29 |
| M10 | 12 | 11,7 | 11,4 | 18 | 17,5 | 2,5 | 14 | 7 | 6,5 | 24 | 12 | 46 |
| M12 | 14 | 13,7 | 13,4 | 22 | 21,5 | 2,5 | 16 | 8 | 7,5 | 35 | 14 | 67 |
| M16 | 18 | 17,7 | 17,4 | 28 | 27,5 | 2,5 | 20 | 10 | 9,5 | 75 | 18 | 128 |
| M20 | 22 | 21,7 | 21,4 | 35 | 34,5 | 2,5 | 28 | 14 | 13,5 | 165 | 22 | 196 |
| M24 | 28 | 27,7 | 27,4 | 44 | 43 | 4 | 36 | 18 | 17 | 345 | 28 | 282 |
| M30 | 36 | 35,6 | 35,3 | 54 | 53 | 6 | 44 | 22 | 21 | 770 | 36 | 448 |
| M36 | 42 | 41,6 | 41,3 | 65 | 54 | 6 | 52 | 26 | 25 | 1030 | 42 | 653 |
| M42 | 48 | 47,6 | 47,3 | 75 | 74 | 6 | 60 | 30 | 29 | 1550 | 48 | 653 |
| M48 | 54 | 53,6 | 53,2 | 85 | 84 | 6 | 70 | 34 | 33 | 2300 | 54 | 653 |
- Row 11 (M36): M36: e min. prints 54 against the ladder's max.-minus-1 progression (e nominal 65 → siblings print min. within ~1 of nominal, M30 65/53→M42 75/74); and F min. 653 at M36 repeats unchanged through M42 and M48. Carried verbatim, not normalized.
Materials
- Material and hardness specified per RFQ — T-slot nuts take stud torque and hammer seating, so the trade default is case-hardened or heat-treated steel; confirm hardness, finish and any stainless need at quotation, and state the table slot standard (the DIN 650-class widths) with the order
Ordering & documentation
Documents
Shipments of ISO 299 Nuts for T-Slots are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 299 Nuts for T-Slots orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ISO 299 Nuts for T-Slots), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for ISO 299 Nuts for T-Slots: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for iso 299 nuts for t-slots is 10,000 pieces (applies to the standard sizes and finishes for iso 299 nuts for t-slots; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 299 nuts for t-slots run 3–7 days. Quantities or variants of iso 299 nuts for t-slots outside the standard range are confirmed at quotation.
Storage & shipping
ISO 299 Nuts for T-Slots are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 299 nuts for t-slots dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
This page and the DIN 508 T-slot nut page in this catalog — which one do I order from?
Order by the designation your table and drawing call out — the fit dimensions govern, and the two captures tabulate different things. The DIN 508 page (x47 capture) carries the DIN column set: width across flats s, tongue offset f, height h, key k, and the "for T-slots according to DIN 650" slot mapping. This ISO 299 capture carries the ISO column set: the slot-fit envelope as F min. (minimum T-slot width), tongue width a in a nominal/max./min. triple, tongue depth d, and weight. Physically both are tongue-and-key threaded blocks over the same M4–M48 span, and where the columns overlap (f, h, k) the ladders sit within the same envelope — but this batch does not claim token identity between the two designations, and the ISO capture's large-end rows carry flagged print defects (e min. at M36, the 653 F plateau at M36–M48) you should confirm per RFQ if you are ordering the large sizes. Practical rule: a drawing marked DIN 508 → the DIN page; marked ISO 299, or ordered against a machine builder's slot-width spec → this page. Material and hardness stay per RFQ on both.
What is the MOQ and lead time for ISO 299 Nuts for T-Slots?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for ISO 299 Nuts for T-Slots state?
State the full designation (ISO 299), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ISO 299 Nuts for T-Slots inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your ISO 299 Nuts for T-Slots
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support