2H14 Two Hole Truss Head Self Tapping Security Screws

Truss head two-hole self-tapping security screws, No.8 and No.10 as tabulated (4.2 and 4.8 mm nominal): head diameters 9.5 and 10.5 mm, head heights 2.2 and 2.75 mm. Marked lengths run 3/8″ to 2″ per the collected matrix; no standard material line stated on the collected page.

Last updated: 2026-11

Request a Quote

2H14 Two Hole Truss Head Self Tapping Security Screws in an industrial setting
Illustrative image redrawn from real 2H14 Two Hole Truss Head Self Tapping Security Screws product references — not a photograph of stocked items.

Specifications

The truss head is the wide-load spreader of the two-hole self-tapping line: a low-profile dome broader than a pan head at the same gauge, sitting on a large bearing circle that holds thin sheet, plastics and soft substrates without pulling through — the collected page calls it a low profile domed head, difficult to remove without the special tool. The collected tabulation covers two gauges, No.8 and No.10 (nominal 4.2 and 4.8 mm), with head diameters 9.5 and 10.5 mm and head heights 2.2 and 2.75 mm, and records the pig-nose/snake-eye alias lineage. The application framing matches the family: areas where aesthetics matter more than security — trains, public lifts — with the reusable two-way insert drive, low to medium torque and the usual cam-out and bit-wear caveats. The length matrix is marked per cell: both gauges from 3/8″ through 1 1/2″, with 2″ marked on No.10 only. Two fail-closed notes: the page states no standard material line, so material is confirmed at quotation; and the page also tabulates an imperial-thread availability table whose relationship to this self-tapping product is ambiguous in the collected source — not interpreted and not claimed here.

Designation 2H14 — truss head self-tapping security screw, two-hole drive; low-profile wide dome, thread-cutting point, two-pin insert bit
Gauge range (tabulated) No.8, No.10 (nominal 4.2 and 4.8 mm)
Head diameter dk per gauge (mm) No.8 9.5 · No.10 10.5
Head height k per gauge (mm) No.8 2.2 · No.10 2.75
Tool size (collected) No.8 · No.10 two-pin insert bits by gauge
Length availability (as marked) No.8 3/8″–1 1/2″ · No.10 3/8″–2″ (as marked in the collected matrix; pairs outside confirmed at quotation)
Security principle Reusable two-way fixing, low/medium security resistance, low to medium torque; difficult to remove without the special insert bit per the collected page
Application (source-stated) Where aesthetics are more important than security — e.g. trains, public lifts

Materials

  • Confirmed at quotation (collected page states no standard material line)

Ordering & documentation

Documents

Shipments of 2H14 Two Hole Truss Head Self Tapping Security Screws are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for 2H14 Two Hole Truss Head Self Tapping Security Screws orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (2H14 Two Hole Truss Head Self Tapping Security Screws), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for 2h14 two hole truss head self tapping security screws is 10,000 pieces (applies to the standard sizes and finishes for 2h14 two hole truss head self tapping security screws; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for 2h14 two hole truss head self tapping security screws run 3–7 days. Quantities or variants of 2h14 two hole truss head self tapping security screws outside the standard range are confirmed at quotation.

Storage & shipping

2H14 Two Hole Truss Head Self Tapping Security Screws are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store 2h14 two hole truss head self tapping security screws dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Truss head or pan head — which for thin sheet with a two-hole drive?

The truss head exists for the sheet that would pull through: its dome is broader and lower, so the clamp spreads over a wider bearing circle at 2.2 mm head height on No.8 rather than digging. The pan head 2H04 is the taller, narrower generalist for panels with more substance. Both take the same twin-hole insert drive and behave identically as reusable two-way fixings — the substrate decides.

Why does this page quote only two gauges and no material?

Because that is all the collected source tabulates and states: the dimension table covers No.8 and No.10 only, and the page carries no standard material line. Rather than borrow A2 from sibling SKUs or extend the gauge range from outside knowledge, both are treated as quotation questions — state the gauge, length and environment on the RFQ and the confirmed material and supply schedule come back with the quote.

What is the MOQ and lead time for these security screws?

Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; sizes quoted as available to order, and non-standard sizes or materials, are quoted with a confirmed schedule. Confirm the exact schedule against quantity and size mix at quotation.

What should an RFQ for these security screws state?

State the designation code (2H01 through 2H14) and head style, the drive (two-hole pig nose / snake eye — fitted with a matching two-pin insert bit), thread or tapping size and length, the hole centre distance your existing bits expect (the source notes it varies between makers), material and finish, the substrate or mating part, required certificates, and quantity per size — plus destination country.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your 2H14 Two Hole Truss Head Self Tapping Security Screws inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your 2H14 Two Hole Truss Head Self Tapping Security Screws
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.