ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws

Square recessed flat countersunk head machine screws per ASME B18.6.3, #4 through 5/16 basic diameter in steel or stainless steel. The flush inch-series head with a cam-out-proof square drive — the countersunk screw for powered assembly.

Last updated: 2026-11

Request a Quote

ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws in an industrial setting
Illustrative image redrawn from real ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws product references — not a photograph of stocked items.

Specifications

This is the flush head of the square recess line: a flat countersunk head that seats into a countersunk hole leaving the recess at or just below the surface, driven by a square bit that stays engaged through full torque. The collected ASME B18.6.3 cut sheet covers #4 (0.1120 in basic diameter) through 5/16 with maximum and minimum head diameters, reference head height and full recess gaging columns. At #10 the head seats at 0.362 in maximum diameter with a 0.116 in reference head height, a 0.111 in square recess and a penetration gaging depth of 0.075/0.060 in; driver sizes run 0 through 4 across the range, stepping 2 at #8 and #10. Against the cross recessed flat countersunk head, the square recess holds the bit under side load in deep or awkward countersinks where a Phillips driver tends to slip; against the slotted countersunk head it survives powered drivers without blade walk-out. Because the recess sits below the surrounding surface once seated, penetration gaging depth — not visible head height — is the dimension that decides whether the drive still works after plating.

Standard ASME B18.6.3 — square recessed flat countersunk head machine screws (flush-seating countersunk head, square recess drive)
Size range #4 (0.1120 in) – 5/16 (0.3125 in) basic screw diameter
Dimensions at #4 A (head diameter) max 0.212 in / min 0.191 in; H (head height) ref 0.067 in; M (recess square) ref 0.0696 in; T (recess depth) ref 0.066 in; penetration gaging depth max 0.038 / min 0.028; driver size 0
Dimensions at #10 A max 0.362 in / min 0.333 in; H ref 0.116 in; M ref 0.111 in; T ref 0.127 in; penetration gaging depth max 0.075 / min 0.060; driver size 2
Dimensions at 1/4 A max 0.477 in / min 0.442 in; H ref 0.153 in; M ref 0.1315 in; T ref 0.158 in; penetration gaging depth max 0.095 / min 0.080; driver size 3
Driver sizes 0 (#4), 1 (#6), 2 (#8, #10), 3 (#12, 1/4), 4 (5/16)
Materials Steel, stainless steel — grade and finish confirmed at quotation (tenant supply range)

Materials

  • Steel
  • Stainless steel

Ordering & documentation

Documents

Shipments of ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for asme b18.6.3 square recessed flat countersunk head machine screws is 10,000 pieces (applies to the standard sizes and finishes for asme b18.6.3 square recessed flat countersunk head machine screws; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for asme b18.6.3 square recessed flat countersunk head machine screws run 3–7 days. Quantities or variants of asme b18.6.3 square recessed flat countersunk head machine screws outside the standard range are confirmed at quotation.

Storage & shipping

ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store asme b18.6.3 square recessed flat countersunk head machine screws dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

What countersink angle does this head need?

The collected table carries the head diameter, height and recess gaging columns but does not print the countersink angle, so this page does not state a figure — confirm the countersink drawing at quotation and match the angle of the mating countersink you already cut. The practical rule that does carry over from the collected data: the head is sized by its maximum diameter (0.362 in at #10, for example) and the flushness by the reference head height, so the countersink must leave the full recess depth visible to the driver.

Square recessed or cross recessed countersunk — which for my assembly?

The head forms are equivalent flush countersunk geometries with different drives. The square recess keeps the bit engaged under side load and in deep countersinks where a Phillips driver tends to slip out before full torque; the Phillips is the choice where generic cross-recess tooling must drive every fastener on the line. If drawings mix both, keep the drive called out per drawing — the recesses are not interchangeable and filling a square recess with a Phillips bit rounds both.

What is the MOQ and lead time for these square recess machine screws?

Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; non-stock sizes, lengths or finishes are quoted with a confirmed schedule. Common sizes in this designation are widely stocked — confirm the exact schedule against quantity and size mix at quotation.

What should an RFQ for these square recess machine screws state?

State the standard designation (ASME B18.6.3 — often still called ANSI B18.6.3) and drive type (square recessed; combination slotted + square recessed where both drives are wanted), nominal screw size and thread series with threads per inch, length and head style, material and grade (steel or stainless; state the stainless grade such as 18-8/A2 or 316/A4 if specified), finish (plain, zinc plated, or other), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your ASME B18.6.3 Square Recessed Flat Countersunk Head Machine Screws
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.