DIN 915 Socket Set Screws (Full Dog Point)

Hexagon socket set screws with full dog point per DIN 915 — current norm DIN EN ISO 4028 — M3 to M12 in the collected table, 45H steel or A2/A4 stainless, thread 6g. The pilot-engaging grub screw that locates in a hole instead of biting a surface.

Last updated: 2026-11

Request a Quote

DIN 915 Socket Set Screws (Full Dog Point) in an industrial setting
Illustrative image redrawn from real DIN 915 Socket Set Screws (Full Dog Point) product references — not a photograph of stocked items.

Specifications

The full dog point set screw does not mark its mating part — it enters it: a cylindrical pilot on the tip rides in a matching hole or groove, so the screw locks a hub, collar or gear against rotation while the pilot takes the locating duty. The collected standard table covers M3 through M12, with the dog point diameter (dp) stepping 1.75 / 2.25 / 3.2 / 3.7 / 5.2 / 6.64 / 8.14 mm across those sizes and the pilot length (z) stepping 1.5 to 6 mm; length availability runs l 3–60. Makings are 45H steel or A2/A4 stainless, thread tolerance 6g; at M6 the socket takes a 3 mm hex key with 2 mm minimum engagement (t min/max 2/3.5). DIN 915's current norm is DIN EN ISO 4028. The design intent is opposite to the cone and cup points: the dog point needs a prepared hole to seat in, and in exchange it leaves the shaft surface untouched and holds position without digging deeper over time.

Standard DIN 915 — hexagon socket set screw with full dog point; current norm DIN EN ISO 4028
Collected size range M3 – M12 (length availability l 3 – 60 in the collected table)
Dog point by size (dp / z) M3 1.75 / 1.5; M4 2.25 / 2; M5 3.2 / 2.5; M6 3.7 / 3; M8 5.2 / 4; M10 6.64 / 5; M12 8.14 / 6 mm
Dimensions at M6 dp max 3.7 mm; z 3 mm; s (hex socket) nominal 3 mm; t min/max 2 / 3.5 mm
Strength classes Steel 45H; stainless A2, A4
Thread 6g
Hex socket set screws with dog point, metric - body diameter, point length and point diameter (M3 - M24)All dimensions in millimeters. Labels follow the source grid header chain: D max = body/shank diameter; H nom short / H nom long = dog point length in the two printed tiers (short dog point, long dog point); L preferred min = preferred minimum dog-point length; V max = dog point diameter. The V column follows the ISO 7435 dog-point diameter series and is deliberately different from the ISO 4028 z pilot-diameter ladder carried on this page from a separate collected source; both series are shown as printed by their sources, without reconciliation. The grid starts at M3 — smaller metric sizes are not printed by this source. Values carried verbatim. The D max column prints 4.25 for M6 on this grid where the same guide’s cup-point grid (p.46) prints 4.35 — each grid is carried verbatim as printed.
Nominal sizeThread pitch (mm)D max — body dia (mm)H nom — short dog point length (mm)H nom — long dog point length (mm)L preferred min — dog point (mm)V max — dog point dia (mm)
M30.52.100.751.55.02.00
M40.72.751.002.05.02.50
M50.83.701.252.56.03.50
M61.004.251.503.06.04.00
M81.256.002.004.08.05.50
M101.507.402.505.08.07.00
M121.758.603.006.012.08.50
M162.0012.354.008.016.012.00
M202.5016.005.0010.020.015.00
M243.0018.956.0012.022.018.00

Materials

  • Steel
  • Stainless steel

Ordering & documentation

Documents

Shipments of DIN 915 Socket Set Screws (Full Dog Point) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 915 Socket Set Screws (Full Dog Point) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 915 Socket Set Screws (Full Dog Point)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for din 915 socket set screws (full dog point) is 10,000 pieces (applies to the standard sizes and finishes for din 915 socket set screws (full dog point); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 915 socket set screws (full dog point) run 3–7 days. Quantities or variants of din 915 socket set screws (full dog point) outside the standard range are confirmed at quotation.

Storage & shipping

DIN 915 Socket Set Screws (Full Dog Point) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 915 socket set screws (full dog point) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Does a dog-point set screw need a special hole in the shaft?

Yes — that is the point of the design. The cylindrical pilot (dp by z in the collected table) is meant to ride in a matching drilled hole or a groove in the shaft, which is what lets it locate a hub or collar without cutting into the surface the way cup or cone points do. The hole diameter should match the pilot, and the pilot length sets how deep it engages. If your assembly has no prepared hole, a cup point (DIN 916) that bites its own seat is the lower-preparation alternative — the trade-off is a permanent surface mark.

What is the MOQ and lead time for these screws?

Minimum order quantity is 10,000 pieces per item. Stocked sizes ship in 3–7 days; non-stock diameters, lengths or finishes are quoted with a confirmed schedule. Common sizes in this designation are widely stocked — confirm the exact schedule against quantity and size mix at quotation.

What should an RFQ for these screws state?

State the standard designation (for example DIN 914, DIN 915, DIN 7981/7982/7983 — or the ISO designation your drawing prints), thread or tapping size, length or head dimension, strength class or material (such as 45H, 4.8, A2-70, A4-80 or brass), finish (black oxide, zinc plated, or plain), required certificates such as a mill test report per EN 10204 3.1, and quantity per size — plus destination country.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 915 Socket Set Screws (Full Dog Point) inquiry

  • ✓ Identify the screw type and standard, including head style and drive recess.
  • ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
  • ✓ State the material/property class, substrate material and thickness, and required coating or finish.
  • ✓ Describe installation, locking or removal requirements, quantity and destination.
  • ✓ Factory-direct pricing for your DIN 915 Socket Set Screws (Full Dog Point)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.