Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties
Head, body and socket dimensions for ASME B18.3 socket head cap screws across the full inch ladder from #0 to 1-1/2, with alloy-vs-stainless mechanical properties and length tolerances, transcribed row-for-row from the collected charts.
Last updated: 2026-11
Specifications
The inch socket head cap screw is the default fastener of precision assembly — jigs, dies, machine tools, enclosures — and this page carries its acceptance data across the whole ladder: twenty sizes from #0 (0.060 in body) to 1-1/2 (1.500 in body), each with body diameter, head diameter and head height max/min pairs, the hex socket nominal, key engagement and chamfer limits, read off the collected B18.3 chart. The ladder is uniform by design: head height runs half the nominal diameter (0.375 at 1/4, 0.750 at 1/2, 1.500 at 1-1/2), the socket is half the diameter again in across-flats terms (3/16 at 1/4, 3/8 at 1/2), and the wall thickness between socket and head wall shrinks to a few thousandths at the small end — which is why the chart tabulates it. Alongside the geometry sit the mechanical figures a design check needs: minimum tensile and yield per size in pounds for alloy and stainless, single-shear of the body, and the tightening-torque ladder — at 1/4-20 alloy that is 5,725 lb minimum tensile and 200 in-lb of recommended torque; at 1/2 alloy, 25,540 lb and 1,800 in-lb. Length tolerances close the page: a 1/4 screw 1 in long carries -0.03 in, the same size at 4 in -0.12 in. Reading notes carried from the source: the socket-strength pair of sub-columns prints duplicated "Min" labels (flagged on the table — read them as the wall-thickness envelope), and the stainless columns blank out above #10, because the common stainless ladder ends there — larger stainless sizes are per RFQ, not silent extrapolations. Finish, thread gaging and corrosion class are RFQ decisions.
| Standard | ASME B18.3 — socket head cap screws, inch series; 20-size ladder #0 through 1-1/2, UNC/UNF threads per size |
|---|---|
| Per-row data (in) | Body, head diameter and head height max/min; top and bottom chamfer; hex socket nominal; key engagement; wall thickness envelope — e.g. 1/4: body 0.2500/0.2435, head 0.375/0.365, socket 3/16 |
| Mechanical properties (lbs min) | Tensile, yield, single shear and tightening torque per size, alloy vs stainless — 1/4 alloy: 5,725 lb tensile, 200 in-lb torque; 1/2 alloy: 25,540 lb, 1,800 in-lb |
| Stainless coverage | Stainless strength columns run #1 through #10/1/2 in the collected charts; larger stainless sizes not tabulated — per RFQ (state size and corrosion environment) |
| Length tolerance | −0.03 in (≤1 in screws, ≤3/8 in thread length) scaling to −0.20 in (7/8–1-1/2 screws, over 6 in long); full matrix on the page |
| Finish / gaging | Not tabulated — per RFQ |
| Size | Body Dia. (D) Max | Body Dia. (D) Min | Head Dia. (A) Max | Head Dia. (A) Min | Head Height (H) Max | Head Height (H) Min | Top Chamfer (C) Max | Top Chamfer (C) Min | Hex Socket (J) Nom | Key Engagement (T) Max | Key Engagement (T) Min | Wall Thickness (G) 1st Min* | Wall Thickness (G) 2nd Min* | Bottom Chamfer (K) Max |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 0 | 0.0600 | 0.0568 | 0.096 | 0.091 | 0.060 | 0.057 | 0.004 | 0.050 | 0.0510 | 0.0500 | 0.025 | 0.020 | 0.007 | |
| 1 | 0.0730 | 0.0695 | 0.118 | 0.112 | 0.073 | 0.070 | 0.005 | 1/16 | 0.0635 | 0.0635 | 0.031 | 0.025 | 0.007 | |
| 2 | 0.0860 | 0.0822 | 0.140 | 0.134 | 0.086 | 0.083 | 0.008 | 5/64 | 0.0791 | 0.0781 | 0.038 | 0.029 | 0.007 | |
| 3 | 0.0990 | 0.0949 | 0.161 | 0.154 | 0.099 | 0.095 | 0.008 | 5/64 | 0.0791 | 0.0781 | 0.044 | 0.034 | 0.007 | |
| 4 | 0.1120 | 0.1075 | 0.183 | 0.176 | 0.112 | 0.108 | 0.009 | 3/32 | 0.0952 | 0.0937 | 0.051 | 0.038 | 0.008 | |
| 5 | 0.1250 | 0.1202 | 0.205 | 0.198 | 0.125 | 0.121 | 0.012 | 3/32 | 0.0952 | 0.0937 | 0.057 | 0.043 | 0.008 | |
| 6 | 0.1380 | 0.1329 | 0.226 | 0.218 | 0.138 | 0.134 | 0.013 | 7/64 | 0.1111 | 0.1094 | 0.064 | 0.047 | 0.008 | |
| 8 | 0.1640 | 0.1585 | 0.270 | 0.262 | 0.164 | 0.159 | 0.014 | 9/64 | 0.1426 | 0.1406 | 0.077 | 0.056 | 0.008 | |
| 10 | 0.1900 | 0.1840 | 0.312 | 0.303 | 0.190 | 0.185 | 0.016 | 5/32 | 0.1587 | 0.1562 | 0.090 | 0.065 | 0.008 | |
| 1/4 | 0.2500 | 0.2435 | 0.375 | 0.365 | 0.250 | 0.244 | 0.025 | 3/16 | 0.1900 | 0.1875 | 0.120 | 0.095 | 0.010 | |
| 5/16 | 0.3125 | 0.3053 | 0.469 | 0.457 | 0.312 | 0.306 | 0.033 | 1/4 | 0.2530 | 0.2500 | 0.151 | 0.119 | 0.010 | |
| 3/8 | 0.3750 | 0.3678 | 0.562 | 0.550 | 0.375 | 0.368 | 0.040 | 5/16 | 0.3160 | 0.3125 | 0.182 | 0.143 | 0.010 | |
| 7/16 | 0.4375 | 0.4294 | 0.656 | 0.642 | 0.438 | 0.430 | 0.047 | 3/8 | 0.3790 | 0.3750 | 0.213 | 0.166 | 0.010 | |
| 1/2 | 0.5000 | 0.4919 | 0.750 | 0.735 | 0.500 | 0.492 | 0.055 | 3/8 | 0.3790 | 0.3750 | 0.245 | 0.190 | 0.015 | |
| 5/8 | 0.6250 | 0.6163 | 0.938 | 0.921 | 0.625 | 0.616 | 0.070 | 1/2 | 0.5050 | 0.5000 | 0.307 | 0.238 | 0.015 | |
| 3/4 | 0.7500 | 0.7406 | 1.125 | 1.107 | 0.750 | 0.740 | 0.085 | 5/8 | 0.6310 | 0.6250 | 0.370 | 0.285 | 0.015 | |
| 7/8 | 0.8750 | 0.8647 | 1.312 | 1.293 | 0.875 | 0.864 | 0.100 | 3/4 | 0.7570 | 0.7500 | 0.432 | 0.333 | 0.020 | |
| 1 | 1.0000 | 0.9886 | 1.500 | 1.479 | 1.000 | 0.988 | 0.114 | 3/4 | 0.7570 | 0.7500 | 0.495 | 0.380 | 0.020 | |
| 1 1/4 | 1.2500 | 1.2336 | 1.875 | 1.852 | 1.250 | 1.236 | 0.144 | 7/8 | 0.8850 | 0.8750 | 0.620 | 0.475 | 0.020 | |
| 1 1/2 | 1.5000 | 1.4818 | 2.250 | 2.224 | 1.500 | 1.485 | 0.176 | 1 | 1.0100 | 1.0000 | 0.745 | 0.570 | 0.020 |
- Row 1 (0): The source grid prints duplicate "Min" sub-labels over the last two wall-thickness columns (marked *); the original rowspan header most likely reads Max/Min. Values reproduced verbatim — treat the pair as the wall-thickness envelope, verify against B18.3 for critical design.
| Thread Length Group | Up to 1 in. | Over 1 in. to 2-1/2 in. | Over 2-1/2 to 6 in. | Over 6 in. |
|---|---|---|---|---|
| 0 thru 3/8, Incl. | -0.03 | -0.04 | -0.06 | -0.12 |
| 7/16 thru 3/4, Incl. | -0.03 | -0.06 | -0.08 | -0.12 |
| 7/8 thru 1-1/2, Incl. | -0.05 | -0.10 | -0.14 | -0.20 |
| Size | Tensile UNRC Alloy (lbs min) | Tensile UNRC Stainless (lbs min) | Tensile UNRF Alloy (lbs min) | Tensile UNRF Stainless (lbs min) | Yield UNRC Alloy (lbs min) | Yield UNRC Stainless (lbs min) | Yield UNRF Alloy (lbs min) | Yield UNRF Stainless (lbs min) | Single Shear Alloy (lbs min) | Single Shear Stainless (lbs min) | Torque UNRC Alloy (in.-lbs) | Torque UNRC Stainless (in.-lbs) | Torque UNRF Alloy (in.-lbs) | Torque UNRF Stainless (in.-lbs) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 0 | - | - | 320 | 145 | - | - | 290 | 72 | 305 | 130 | - | - | 2.6 | 1.4 |
| 1 | 475 | - | 500 | 220 | 425 | - | 450 | 111 | 450 | 190 | 4.5 | - | 4.8 | 2.3 |
| 2 | 665 | 295 | 710 | - | 600 | 185 | 635 | - | 625 | 260 | 7.5 | 3.8 | 8.0 | - |
| 3 | 875 | - | 940 | - | 790 | - | 845 | - | 830 | - | 11.0 | - | 12.0 | - |
| 4 | 1,090 | 480 | 1,190 | - | 975 | 240 | 1,070 | - | 1,060 | 350 | 16.0 | 6.0 | 18.0 | - |
| 5 | 1,430 | - | 1,490 | - | 1,290 | - | 1,345 | - | 1,325 | - | 24.0 | - | 24.0 | - |
| 6 | 1,640 | 725 | 1,825 | - | 1,470 | 363 | 1,645 | - | 1,615 | 375 | 30.0 | 15.0 | 34.0 | - |
| 8 | 2,520 | 1,120 | 2,650 | - | 2,270 | 560 | 2,385 | - | 2,280 | 670 | 55.0 | 28.0 | 58.0 | - |
| 10 | 3,150 | 1,400 | 3,600 | 1,600 | 2,835 | 701 | 3,240 | 800 | 3,060 | 950 | 79.0 | 40.0 | 90.0 | 46.0 |
| 1/4 | 5,725 | 2,550 | 6,550 | 2,910 | 5,150 | 1,273 | 5,900 | 1,455 | 5,295 | 2,200 | 200.0 | 95.0 | 230.0 | 109.0 |
| 5/16 | 9,430 | 4,200 | 10,440 | 4,645 | 8,490 | 2,100 | 9,395 | 2,230 | 8,285 | 3,450 | 415.0 | 170.0 | 460.0 | 188.0 |
| 3/8 | 13,950 | 6,100 | 15,805 | 7,025 | 12,555 | 3,100 | 14,225 | 3,510 | 11,910 | 4,970 | 740.0 | 301.0 | 845.0 | 341.0 |
| 7/16 | 19,135 | - | 21,365 | - | 17,220 | - | 19,230 | - | 16,200 | - | 1,190.0 | - | 1,305.0 | - |
| 1/2 | 25,540 | 11,350 | 28,780 | - | 22,990 | 5,675 | 25,905 | - | 21,175 | 8,840 | 1,800.0 | 750.0 | 2,065.0 | - |
| 5/8 | 38,400 | - | 43,500 | - | 34,550 | - | 39,150 | - | 31,300 | - | 3,400.0 | - | 3,800.0 | - |
| 3/4 | 56,750 | - | 63,400 | - | 51,100 | - | 57,050 | - | 45,050 | - | 6,000.0 | - | 6,750.0 | - |
| 7/8 | 78,500 | - | 86,500 | - | 70,700 | - | 77,850 | - | 61,350 | - | 8,250.0 | - | 9,200.0 | - |
| 1 | 103,000 | - | 112,700 | - | 92,700 | - | 101,450 | - | 80,100 | - | 12,500.0 | - | 13,000.0 | - |
| 1-1/4 | 164,700 | - | 182,400 | - | 148,250 | - | 164,150 | - | 125,100 | - | 25,000.0 | - | 27,750.0 | - |
| 1-1/2 | 238,800 | - | 268,800 | - | 215,950 | - | 241,900 | - | 180,200 | - | 43,500.0 | - | 49,000.0 | - |
- Row 1 (0): Size 0 prints "-" across both tensile UNRC pairs and both torque UNRC pairs — the source chart does not tabulate those figures for size 0; no value is inferred.
Materials
- Alloy steel (quenched and tempered, ~180,000 psi tensile class through 1/2 in) and austenitic stainless (80,000 psi class) — the charts are geometry data and are material-independent; state alloy and finish at RFQ
Ordering & documentation
Documents
Shipments of Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for socket head cap screw dimensions — asme b18.3 inch ladder (#0 to 1-1/2) with mechanical properties is 10,000 pieces (applies to the standard sizes and finishes for socket head cap screw dimensions — asme b18.3 inch ladder (#0 to 1-1/2) with mechanical properties; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for socket head cap screw dimensions — asme b18.3 inch ladder (#0 to 1-1/2) with mechanical properties run 3–7 days. Quantities or variants of socket head cap screw dimensions — asme b18.3 inch ladder (#0 to 1-1/2) with mechanical properties outside the standard range are confirmed at quotation.
Storage & shipping
Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store socket head cap screw dimensions — asme b18.3 inch ladder (#0 to 1-1/2) with mechanical properties dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Why does the alloy column matter so much more than the stainless one on a socket screw chart, and when is the stainless figure the one to design with?
The two materials answer different failure questions. Alloy socket screws are through-hardened to roughly 180,000 psi minimum tensile, so their column (5,725 lb at 1/4, 25,540 lb at 1/2, 238,800 lb at 1-1/2) is the one that sizes a structural or clamping joint — the screw thread, not the head, is the limit, and the tightening-torque ladder is derived from it. Stainless columns run at roughly half those figures (2,550 lb at 1/4) because austenitic stainless cannot be through-hardened by heat treatment — and the printed values blank out entirely above the small-to-mid sizes in the collected charts, because that is where the common product line ends, not because the material stops existing. Design with the stainless figure when the joint sees moisture, washdown, chemicals or elevated temperature where retaining properties matters more than peak strength, and upsize the screw to recover the load — or move to an alloy screw with a coating. What the chart cannot decide: the corrosion class (304 vs 316 vs A286), the finish, or whether a joint actually needs the alloy preload — those are application calls, so state the environment and load at RFQ.
What is the MOQ and lead time for socket screws referenced by these charts?
The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Confirm the exact schedule against quantity, size mix and finish at quotation.
What is the MOQ and lead time for Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties state?
State the full designation (ASME B18.3), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your Socket Head Cap Screw Dimensions — ASME B18.3 Inch Ladder (#0 to 1-1/2) with Mechanical Properties
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support