ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm)
British Standard Pipe thread dimensions per ISO 228 (parallel BSPP/G) and ISO 7 (taper BSPT/R) — TPI, pitch, thread height and major/pitch/minor diameters in millimetres per nominal size from 1/16 to 6, transcribed row-for-row from the collected chart.
Last updated: 2026-11
Specifications
British Standard Pipe threads are the Whitworth-form family (55° flanks, rounded crests) that dominates plumbing and fluid power outside the North American NPT world — and the naming trap is the size: a "1/4 in BSP" fitting has a 13.157 mm major diameter, nothing to do with a 1/4 UNC bolt or a 1/4 NPT fitting. The collected chart prints the geometry per nominal size from 1/16 to 6: TPI (28 down to 11), pitch, thread height, and the major/pitch/minor diameters (1/4 in: 13.157 / 12.301 / 11.445 mm). One geometry serves two standards: ISO 228's parallel thread (BSPP, designated G) seals on a face or gasket at the fitting end — washer-flange fittings — while ISO 7's taper variant (BSPT, designated R) seals on the thread flanks with compound, the same sealing concept as NPT but a different flank angle and crest form, which is why BSP and NPT hardware must never be mixed even where sizes look adjacent (a 1/2 BSP at 14 TPI/55° against a 1/2 NPT at 14 TPI/60° threads up ruinously and does not seal). The source flags that the ladder has no 5/8 BSP size (footnote on the table below) and its quick-answer table is a subset of the ladder — one geometry, two sealing philosophies; pressure ratings and gasket selection are per RFQ.
| Standard | ISO 228 — parallel BSPP threads (G designation) and ISO 7 — taper BSPT threads (R designation); Whitworth form, 55° flank angle, rounded crests |
|---|---|
| Size range | Nominal sizes 1/16 – 6, 14 rows; TPI 28 down to 11; dimensions in millimetres |
| Tabulated geometry (mm) | Per row: TPI, pitch, height of thread, major/pitch/minor diameters; example 1/4: 19 TPI, 1.337 pitch, 0.856 height, 13.157 / 12.301 / 11.445 |
| Size naming | BSP designations are nominal pipe sizes — the actual major diameter differs (1/8: 9.728 mm, 1/2: 20.955 mm); never cross-match BSP to UNC or NPT by name |
| Sealing variants / ratings | Parallel (face/gasket seal) vs taper (thread+compound seal) is the BSPP/BSPT split; pressure ratings, gaskets and NPT interchange are not tabulated — per RFQ |
| Designation | TPI | Pitch (mm) | Height of Thread (mm) | Major Diameter (mm) | Pitch Diameter (mm) | Minor Diameter (mm) |
|---|---|---|---|---|---|---|
| 1/16 | 28 | 0.907 | 0.581 | 7.723 | 7.142 | 6.561 |
| 1/8 | 28 | 0.907 | 0.581 | 9.728 | 9.147 | 8.566 |
| 1/4 | 19 | 1.337 | 0.856 | 13.157 | 12.301 | 11.445 |
| 3/8 | 19 | 1.337 | 0.856 | 16.662 | 15.806 | 14.950 |
| 1/2 | 14 | 1.814 | 1.162 | 20.955 | 19.793 | 18.631 |
| 3/4 | 14 | 1.814 | 1.162 | 26.441 | 25.279 | 24.117 |
| 1 | 11 | 2.309 | 1.479 | 33.249 | 31.770 | 30.291 |
| 1 1/4 | 11 | 2.309 | 1.479 | 41.910 | 40.431 | 38.952 |
| 1 1/2 | 11 | 2.309 | 1.479 | 47.803 | 46.324 | 44.845 |
| 2 | 11 | 2.309 | 1.479 | 59.614 | 58.135 | 56.656 |
| 2 1/2 | 11 | 2.309 | 1.479 | 75.184 | 73.705 | 72.226 |
| 3 | 11 | 2.309 | 1.479 | 87.884 | 86.405 | 84.926 |
| 4 | 11 | 2.309 | 1.479 | 113.030 | 111.551 | 110.072 |
| 6 | 11 | 2.309 | 1.479 | 163.830 | 162.351 | 160.872 |
- Row 1 (1/16): The source notes 5/8 BSP is not carried in standard ISO 228 / ISO 7 tables; the ladder steps 1/2 → 3/4 with no 5/8 row. Verify the fitting standard or measure OD and TPI to identify non-standard sizes.
| Designation | TPI (n) | Pitch P (mm) | Major Dia. D (mm) | Pitch Dia. D2 (mm) | Minor Dia. D1 (mm) |
|---|---|---|---|---|---|
| 1/16 | 28 | 0.907 | 7.723 | 7.142 | 6.561 |
| 1/8 | 28 | 0.907 | 9.728 | 9.147 | 8.566 |
| 1/4 | 19 | 1.337 | 13.157 | 12.301 | 11.445 |
| 3/8 | 19 | 1.337 | 16.662 | 15.806 | 14.95 |
| 1/2 | 14 | 1.814 | 20.955 | 19.793 | 18.631 |
| 5/8 | 14 | 1.814 | 22.911 | 21.749 | 20.587 |
| 3/4 | 14 | 1.814 | 26.441 | 25.279 | 24.117 |
| 7/8 | 14 | 1.814 | 30.201 | 29.039 | 27.877 |
| 1 | 11 | 2.309 | 33.249 | 31.77 | 30.291 |
| 1 1/8 | 11 | 2.309 | 37.897 | 36.418 | 34.939 |
| 1 1/4 | 11 | 2.309 | 41.91 | 40.431 | 38.952 |
| 1 1/2 | 11 | 2.309 | 47.803 | 46.324 | 44.845 |
| 1 3/4 | 11 | 2.309 | 53.746 | 52.267 | 50.788 |
| 2 | 11 | 2.309 | 59.614 | 58.135 | 56.656 |
| 2 1/4 | 11 | 2.309 | 65.71 | 64.231 | 62.752 |
| 2 1/2 | 11 | 2.309 | 75.184 | 73.705 | 72.226 |
| 2 3/4 | 11 | 2.309 | 81.534 | 80.055 | 78.576 |
| 3 | 11 | 2.309 | 87.884 | 86.405 | 84.926 |
| 3 1/2 | 11 | 2.309 | 100.33 | 98.851 | 97.372 |
| 4 | 11 | 2.309 | 113.03 | 111.551 | 110.072 |
| 4 1/2 | 11 | 2.309 | 125.73 | 124.251 | 122.772 |
| 5 | 11 | 2.309 | 138.43 | 136.951 | 135.472 |
| 5 1/2 | 11 | 2.309 | 151.13 | 149.651 | 148.172 |
| 6 | 11 | 2.309 | 163.83 | 162.351 | 160.872 |
- Row 5 (1/2): 5/8 row present in this fuller ISO 228-1 ladder (major 22.911 mm) — supersedes the earlier table's note that the ladder steps 1/2 → 3/4 with no 5/8 row. The 5/8 size exists in ISO 228-1 but is rarely stocked.
Materials
- Fitting material, gasket/O-ring selection and sealant specified per RFQ — BSPP seals at the face, BSPT on the flanks; state which when quoting
Ordering & documentation
Documents
Shipments of ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for iso 228 / iso 7 british standard pipe threads — bspp (g) / bspt (r) dimensions 1/16 – 6 (mm) is 10,000 pieces (applies to the standard sizes and finishes for iso 228 / iso 7 british standard pipe threads — bspp (g) / bspt (r) dimensions 1/16 – 6 (mm); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for iso 228 / iso 7 british standard pipe threads — bspp (g) / bspt (r) dimensions 1/16 – 6 (mm) run 3–7 days. Quantities or variants of iso 228 / iso 7 british standard pipe threads — bspp (g) / bspt (r) dimensions 1/16 – 6 (mm) outside the standard range are confirmed at quotation.
Storage & shipping
ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store iso 228 / iso 7 british standard pipe threads — bspp (g) / bspt (r) dimensions 1/16 – 6 (mm) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
BSPP and BSPT share the same thread geometry — so what differs, and why can't BSP fittings mate with NPT?
The geometry is shared — the collected chart's one set of diameters serves both — and the difference is the sealing philosophy. BSPP (ISO 228, G) is cut parallel: the thread provides mechanical clamping only, and sealing happens at the fitting's face against a bonded washer, O-ring or metal gasket — which makes BSPP joints repeatable and reusable, the reason hydraulics and instrumentation prefer it. BSPT (ISO 7, R) is cut on the same 1-in-16-type taper concept as NPT: flank interference plus sealant makes the joint, so it suits welded-adjacent plumbing and less-frequently-disturbed runs. Neither parallelism nor taper is an option to choose by feel — the mating port decides. Against NPT the incompatibility is hard geometric: BSP runs the 55° Whitworth form with rounded crests at 14 or 11 TPI on its sizes; NPT runs 60° sharp-ish forms at its own TPI ladder. A 1/2 BSP against a 1/2 NPT starts together (both 14 TPI), binds after a turn or two, wrecks both threads and never seals — the most common fitting-counter error where the two worlds meet. The practical discipline: identify fittings by measuring OD and TPI against the chart (the size names lie — "1/4 BSP" is 13.157 mm major), and never adapt BSP to NPT with sealant and force.
What is the MOQ and lead time for threaded parts on this standard?
The minimum order quantity is 10,000 pieces. Stock items ship in 3–7 days; non-stock items are confirmed at quotation. Common thread sizes on this standard are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
What is the MOQ and lead time for ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm)?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm) state?
State the full designation (ISO 228), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm) inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your ISO 228 / ISO 7 British Standard Pipe Threads — BSPP (G) / BSPT (R) Dimensions 1/16 – 6 (mm)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support