Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230)
VDI 2230 part 1 friction ranges for bolted joints: μG (thread) and μK (bearing) bands from 0.04 to ≥0.30 mapped to surface material/coating families and lubrication states — the assembly-torque basis table.
Last updated: 2026-11
Specifications
Every torque-controlled assembly is a friction guess until this table is consulted. The VDI 2230 part 1 ranges collected here map the realistic μG/μK windows to what is actually on the parts: bright/black-oxide/phosphate/electroplated surfaces with solid-film lubricants run 0.04-0.10; the same surfaces dry or in delivery state sit at 0.08-0.16 and climb to 0.14-0.24 without lubricant; hot-dip galvanizing with MoS2 or wax runs mid-band; austenitic stainless spans wide depending on lubrication and galling tendency; and unlubricated plated or stainless pairs can exceed 0.30. The practical use is preload arithmetic: a torque calculated at μ = 0.12 applied to a dry stainless pair at 0.25 delivers roughly half the intended clamp — this table is where that error gets caught before the joint, not after.
| Source / scope | VDI 2230 part 1 (Systematic calculation of high duty bolted joints) friction ranges for μG (thread) and μK (bearing) — carried verbatim including the source's own closing note |
|---|---|
| 0.04-0.10 | Bright/black oxide/phosphate/electroplated (Zn, Zn/Fe, Zn/Ni), zinc-laminate surfaces; solid lubricants (MoS2, graphite, PTFE, PA, PE, PI) in varnishes, pastes, wax dispersions |
| 0.08-0.16 | Same surfaces + Al/Mg alloys; solid lubricants, greases, oils, delivery state; hot-dip galvanized with MoS2/graphite/wax; organic coatings with integrated solid lubricant |
| 0.14-0.24 | Austenitic steel (waxes/pastes); bright/phosphate delivery state (lightly oiled); electroplated with no lubricant |
| 0.20-0.35 and ≥0.30 | Austenitic with oil; plated/hot-dip without lubricant; ≥0.30 for Zn/Fe, Zn/Ni plated, austenitic, Al/Mg dry — the unlubricated top of the scale |
| Not tabulated | Per-finish K factors (separate registered page), temperature effects, repeated-assembly degradation — per RFQ / joint testing |
| Coefficient of Friction Table for Screw Bolt Friction | ||
|---|---|---|
| Range for μ G and μ K | Typical Examples | |
| Material - Surfaces | Lubricants | |
| 0.04 to 0.10 | Metallically bright Black oxide coating Phosphate conversion coating Electroplated coatings such as Zn, Zn/Fe, Zn/Ni Zinc laminated coatings | Solid lubricants, such as MoS 2 , graphite, PTFE, PA, PE, PI in lubricating varnishes, as top coats or in pastes; liquefied wax; wax dispersions |
| 0.08 to 0.16 | Metallically bright Black oxide coating Phosphate conversion coating Electroplated coatings such as Zn, Zn/Fe, Zn/Ni Zinc laminated coatings Al and Mg alloys | Solid lubricants, such as MoS 2 , graphite, PTFE, PA, PE, PI in lubricating varnishes, as top coats or in pastes; liquefied wax ; wax dispersions, greases; oils; delivery state |
| Hot-dip Galvanized | MoS 2 ; graphite; wax dispersions | |
| Organic coatings | With integrated solid lubricant or wax dispersion | |
| Austenitic steel | Solid lubricants or waxes; pastes | |
| 0.14 to 0.24 | Austenitic steel | Wax dispersions, pastes |
| Metallically bright Phosphate conversion coating | Delivery state (lightly oiled) | |
| Electroplated coatings such as Zn, Zn/Fe, Zn/Ni Zinc laminated coatings | None | |
| 0.20 to 0.35 | Austenitic steel | Oil |
| Electroplated coatings such as Zn, Zn/Fe; Hot-dip galvanized | None | |
| ≥ 0.30 | Electroplated coatings such as Zn/Fe, Zn/Ni Austenitic steel Al, Mg alloys | None |
| Source : From VDI 2230 Part-1 : Systematic calculation of high duty bolted joints - Joints with one cylindrical bolt. |
- The 0.08-0.16 and 0.14-0.24 ranges each span multiple material/lubricant sub-rows (rowspan-expanded): the range value prints once per group as collected and repeats down the expanded grid.
Materials
- Friction is a system property of the pair as installed: surface family from this table, lubrication state from the assembly instruction, and scatter of ±20% or more inside any band. Specify both on torque-critical work — "phosphate, oiled, μ target 0.12" is a specification; "tighten to 200 N·m" alone is not. Stainless and hot-dip galvanized are the two families that punish missing lubrication the hardest (galling and high μ respectively), and both are the cheapest to fix with a specified thread lubricant at assembly
Ordering & documentation
Documents
Shipments of Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for thread and bearing friction coefficient ranges by surface and lubricant (vdi 2230) is 10,000 pieces (applies to the standard sizes and finishes for thread and bearing friction coefficient ranges by surface and lubricant (vdi 2230); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for thread and bearing friction coefficient ranges by surface and lubricant (vdi 2230) run 3–7 days. Quantities or variants of thread and bearing friction coefficient ranges by surface and lubricant (vdi 2230) outside the standard range are confirmed at quotation.
Storage & shipping
Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store thread and bearing friction coefficient ranges by surface and lubricant (vdi 2230) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
How do I use these ranges to sanity-check a torque specification?
Take the target preload from the joint design, pick the μ band matching the actual surface and lubrication from this table, and check the spread: the torque needed at the top of the band versus the bottom tells you the preload scatter you are accepting. If T = F·(0.16P + 0.58·d2·μG + Dk/2·μK) at μ 0.08 gives your 200 N·m wrench setting, the same joint at 0.16 needs nearly double the torque for the same preload — so a specification that ignores the band is delivering whatever the friction feels like that day. Tight bands (solid-film lubricants, controlled coatings) are how critical joints get predictable; the table shows exactly which surface/lubricant combinations buy that predictability.
Why is stainless steel its own row family in the table?
Austenitic stainless threads behave differently from carbon steel: higher adhesion tendency (galling), friction that rises sharply when unlubricated, and wide scatter depending on surface finish and speed. The table gives austenitic steel its own rows in every band for that reason — lubricated with pastes or waxes it sits low-mid; dry it climbs to the top of the scale. Assembly practice follows: specify an anti-galling lubricant on stainless fasteners, control the tightening speed, and expect the first tightening of a fresh nut to run higher friction than subsequent ones. The rows are the standard's acknowledgement that "stainless" is not one friction condition.
What is the MOQ and lead time for Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230)?
Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.
What should an RFQ for Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230) state?
State the full designation (Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230)), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230) inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your Thread and Bearing Friction Coefficient Ranges by Surface and Lubricant (VDI 2230)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support